P0700 on a 2022 Toyota Camry
Transmission Control System Malfunction
What does P0700 mean on a 2022 Toyota Camry?
P0700 is an "informational" code set by the engine control module when the transmission control module (TCM) reports any fault. P0700 itself does not identify a specific transmission problem — it is a flag that tells you to scan the TCM for the underlying code or codes. The actual fault could be anything from a shift solenoid failure to a slipping clutch pack to a low-fluid condition.
Symptoms on a 2022 Toyota Camry
- Check Engine Light is illuminated
- Transmission stuck in a single gear (often 3rd or 4th — "limp mode")
- Hard, delayed, or erratic shifts
- Torque converter clutch not locking up on the highway
- Higher than normal RPM at cruise
- Reduced fuel economy
- Possible transmission slipping under load
Likely causes on a 2022 Toyota Camry
- Low or burnt transmission fluid Most commonEstimated repair: $100– $350
Always check fluid level and condition first; many P0700s clear with a fluid and filter service.
- Failed shift solenoid (one or more) CommonEstimated repair: $250– $900
- Failed transmission speed sensor (input or output) CommonEstimated repair: $150– $500
- Worn or stuck valve body OccasionalEstimated repair: $600– $2,000
- Internal mechanical wear — slipping clutch packs or bands OccasionalEstimated repair: $2,500– $6,000
- Failed transmission control module (TCM) itself RareEstimated repair: $500– $1,500
- Wiring harness damage to TCM or solenoid pack OccasionalEstimated repair: $200– $700
How to diagnose this on a 2022 Toyota Camry
-
Scan the TCM for the specific transmission code
P0700 alone is not actionable. Use a scan tool capable of reading transmission codes (not just engine codes) to retrieve the actual P07XX, P08XX, or P09XX code that triggered the P0700. That code is what to act on.
Tools: Scan tool with TCM access
-
Check fluid level, color, and smell
Most modern transmissions require checking fluid at operating temperature with the engine running and the selector in park or neutral, on a level surface. Dark, brown, or burnt-smelling fluid indicates clutch material in the fluid — fix the root cause; do not just refill.
Tools: Lift or jack and stands (sealed-for-life units), Vehicle-specific fluid spec
-
Inspect the wiring at the transmission case
The external transmission harness is exposed to heat, oil, and road debris. Disconnect, inspect, and reconnect every external connector. A connector full of transmission fluid points to a leaking case seal that has wicked fluid up the harness — replace the seal and sometimes the harness.
Tools: Connector unlock tool, Electrical cleaner
-
Pan-drop and inspect the filter and magnet
Drop the pan and inspect the filter, gasket sealing surface, and the magnet on the bottom of the pan. A magnet covered in fine metallic paste is normal. Large chunks of metal or clutch material indicate internal failure — at that point a teardown or replacement is required.
Tools: Drain pan, Socket set, New filter and gasket
-
Verify TCM and ECM are talking on the CAN bus
Use the scan tool to read live data from both modules simultaneously. If the ECM sees a vehicle speed that disagrees with the TCM, suspect a speed sensor or harness fault. If the TCM is non-responsive, check power, ground, and CAN bus continuity to the module.
Tools: Scan tool with bi-module live data, Multimeter
Known Technical Service Bulletins for the 2020-2024 Toyota Camry
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Toyota Camry.
- ENGINE Feb 26, 2026
OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.
NHTSA #11029896 - ELECTRICAL SYSTEM Jan 29, 2026
OBSOLETE NOTICE January 30, 2026: This bulletin is now obsolete. Please see T-SB-0001-26.
NHTSA #11028726 - ELECTRICAL SYSTEM Jan 27, 2026
Some 2018 – 2024 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.
NHTSA #11028722 - UNKNOWN OR OTHER Jan 6, 2026
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA #11028712 - ENGINE Aug 6, 2025
The specific condition covered by this program is for a small engine coolant leak that can occur from the flow shut-off valve that can allow coolant to drip on other parts of the vehicle. This can cause "Engine Maintenance Required" to be displayed on the instrument cluster or cause the A/C not to function normally. Although the flow shut-off valve is covered by Toyota’s New Vehicle Limited Warranty for 36 months or 36,000 miles (whichever comes first), we at Toyota care about the customers’ ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.
NHTSA #11022949 - ELECTRICAL SYSTEM Jun 24, 2025
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
NHTSA #11020670
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
Common fixes
- Service the transmission fluid and filter to OEM specification
- Replace failed shift solenoid(s)
- Replace failed input or output speed sensor
- Replace or rebuild the valve body
- Replace the TCM
- Major rebuild or replacement of the transmission for internal failures
About the 2020-2024 Toyota Camry
The 2020-2024 Toyota Camry was commonly sold with the following powertrains: 2.5L I4, 3.5L V6, 2.5L Hybrid I4. Common trims include LE, SE, XLE, XSE.
Why P0700 by itself is not a diagnosis
P0700 is set in the ECM because the TCM reported a problem. The TCM stored the actual code. Many cheap OBD-II scanners only read engine codes — they will show P0700 with no further detail, leading to wasted parts swaps. A scan tool that can read transmission codes is essential for diagnosing P0700 efficiently.
P0700 with limp mode (stuck in one gear)
When the TCM detects a fault that could damage the transmission, it commands a default gear (often 3rd or 4th) and disables all shifting. This is “limp mode.” It is meant to let you drive a short distance to a shop, not for daily driving. Continuing to drive in limp mode for weeks can damage internal components even though the limp logic exists to prevent damage.
When to fluid-service vs rebuild
If the underlying transmission code is for a solenoid, sensor, or wiring issue and the fluid is clean, a fluid and filter service plus the failed electrical part is the right repair. If the underlying code is for ratio incorrect (P0731–P0734), torque converter clutch (P0741), or excessive clutch slip, the transmission has mechanical wear and a full rebuild or replacement is more cost-effective than chasing individual parts.