P0720 on a 2022 Toyota Camry
Transmission Output Speed Sensor Malfunction
What does P0720 mean on a 2022 Toyota Camry?
P0720 is set when the transmission control module does not receive a valid signal from the output shaft speed sensor. The TCM uses this signal to compare actual transmission output to expected output for the selected gear and engine RPM — if the signal is missing or implausible, gear ratio calculations fail and the TCM cannot shift correctly. The vehicle typically drops into limp mode (stuck in a default gear, often 3rd or 4th) until the signal is restored.
Symptoms on a 2022 Toyota Camry
- Check Engine Light is illuminated
- Speedometer reads zero or fluctuates erratically
- Transmission locked into a single gear (limp mode)
- Hard, harsh, or no shifts
- Cruise control inoperative
- Vehicle may shudder or hesitate at the moment of shift
- Often paired with P0700 (transmission control malfunction)
Likely causes on a 2022 Toyota Camry
- Failed output shaft speed sensor element Most commonEstimated repair: $150– $500
- Damaged sensor connector or harness CommonEstimated repair: $80– $350
- Metal debris on the sensor tip (from internal transmission wear) CommonEstimated repair: $100– $400
Cleaning the sensor face is a free first attempt.
- Damaged tone ring or reluctor wheel inside the transmission OccasionalEstimated repair: $1,500– $4,500
- Transmission fluid contamination preventing the sensor from reading OccasionalEstimated repair: $200– $700
- Wiring fault between the sensor and the TCM OccasionalEstimated repair: $100– $500
- Failed TCM signal input (rare) RareEstimated repair: $500– $1,500
How to diagnose this on a 2022 Toyota Camry
-
Locate the output speed sensor on this transmission
The output shaft speed sensor is typically a two-wire sensor threaded into the rear of the transmission case (RWD vehicles) or the side of the transaxle (FWD vehicles). Some vehicles have it on the transfer case for 4WD. Confirm location in the service manual.
Tools: Vehicle-specific service information
-
Check connector and visible wiring
Sensor connectors near the transmission case are exposed to heat, road debris, and sometimes fluid leaks. Unplug and inspect for corrosion, transmission fluid migration up the harness, or visible damage. Clean and re-seat.
Tools: Connector unlock tool, Electrical contact cleaner
-
Measure sensor resistance
Most output speed sensors are magnetic or Hall-effect with a typical resistance of 200–1500 Ω. Compare to the service manual. Infinite resistance means an open sensor; near zero means shorted. Either way, replace.
Tools: Multimeter, Service spec sheet
-
Verify signal output during rotation
On a lift with the rear wheels free to rotate, spin a rear wheel slowly by hand while watching the output speed PID. The reading should change in proportion to wheel rotation. No response confirms a dead sensor or damaged tone ring.
Tools: Vehicle lift, Scan tool with output speed PID
-
Inspect sensor tip for debris
Remove the sensor and look at the magnetic tip. Steel slivers stuck to the magnet are normal — large chunks or clutch material is a warning sign that the transmission is shedding material. Clean the tip and reinstall as a first attempt; consider transmission fluid analysis if heavy debris was present.
Tools: Socket, Magnet pick or wire brush
Known Technical Service Bulletins for the 2020-2024 Toyota Camry
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Toyota Camry.
- ENGINE Feb 26, 2026
OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.
NHTSA #11029896 - ELECTRICAL SYSTEM Jan 29, 2026
OBSOLETE NOTICE January 30, 2026: This bulletin is now obsolete. Please see T-SB-0001-26.
NHTSA #11028726 - ELECTRICAL SYSTEM Jan 27, 2026
Some 2018 – 2024 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.
NHTSA #11028722 - UNKNOWN OR OTHER Jan 6, 2026
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA #11028712 - ENGINE Aug 6, 2025
The specific condition covered by this program is for a small engine coolant leak that can occur from the flow shut-off valve that can allow coolant to drip on other parts of the vehicle. This can cause "Engine Maintenance Required" to be displayed on the instrument cluster or cause the A/C not to function normally. Although the flow shut-off valve is covered by Toyota’s New Vehicle Limited Warranty for 36 months or 36,000 miles (whichever comes first), we at Toyota care about the customers’ ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.
NHTSA #11022949 - ELECTRICAL SYSTEM Jun 24, 2025
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
NHTSA #11020670
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
Common fixes
- Clean debris off the output speed sensor tip
- Replace the output shaft speed sensor with an OEM part
- Repair sensor connector or harness damage
- Service transmission fluid (drop pan, replace filter and gasket)
- Internal transmission repair if tone ring or shaft damage is confirmed
About the 2020-2024 Toyota Camry
The 2020-2024 Toyota Camry was commonly sold with the following powertrains: 2.5L I4, 3.5L V6, 2.5L Hybrid I4. Common trims include LE, SE, XLE, XSE.
Why P0720 puts the transmission into limp mode
The TCM continuously compares output shaft speed to engine RPM and selected gear to verify it is actually getting the gear ratio it commanded. Without a valid output speed signal:
- Ratio verification fails (sets P0731-P0734 in some cases)
- Shift point timing breaks (cannot tell vehicle speed for upshifts)
- Torque converter lockup logic fails (depends on accurate speed)
Limp mode is a protection — the TCM picks a safe default gear and holds it until the signal returns. Drive a short distance to a shop; do not attempt long trips in limp mode.
P0720 with metal on the sensor tip
A small amount of metallic dust on the magnetic sensor tip is normal — it’s the natural wear of bearings and gears over the life of the transmission. Large flakes or clutch material is not normal and indicates internal damage that will eventually cause shifting problems beyond the sensor. If you find heavy debris, do a fluid service and inspect the pan magnet too — together they tell the story of what’s happening inside.
P0720 vs P0500 (Vehicle Speed Sensor)
These can look similar but come from different sources:
- P0500 — vehicle speed signal missing (often the ABS wheel speed sensor on modern vehicles)
- P0720 — transmission output shaft speed signal missing specifically from the transmission’s own sensor
On vehicles where the TCM derives “vehicle speed” from the output shaft sensor, both codes can set together from a single sensor failure.