P0741 on a 2022 Toyota Camry
Torque Converter Clutch Stuck Off
What does P0741 mean on a 2022 Toyota Camry?
P0741 is set when the ECM (or TCM) commands the torque converter clutch (TCC) to lock up under cruise conditions and does not see the expected drop in engine RPM relative to vehicle speed. Effectively, the lockup clutch is being commanded but not engaging — or it engages and immediately slips. Either way the converter is running in fluid-coupling mode at highway speed when it should be mechanically locked.
Symptoms on a 2022 Toyota Camry
- Check Engine Light is illuminated
- Engine RPM at highway cruise is 200–400 RPM higher than normal
- Noticeable fuel economy drop on the highway
- Possible transmission fluid overheating warning on towing
- Shudder or vibration at light-throttle cruise (slipping TCC)
- Often paired with P0700 from the TCM
Likely causes on a 2022 Toyota Camry
- Worn or burned torque converter clutch friction material Most commonEstimated repair: $1,800– $4,500
Requires torque converter replacement — major job.
- Failed TCC solenoid in the valve body CommonEstimated repair: $300– $900
- Stuck TCC control valve in the valve body CommonEstimated repair: $400– $1,500
- Low transmission fluid level or contaminated fluid CommonEstimated repair: $100– $400
- Wiring fault to the TCC solenoid OccasionalEstimated repair: $80– $350
- Failed TCM driver for the TCC solenoid RareEstimated repair: $500– $1,500
- Internal transmission damage allowing fluid bypass OccasionalEstimated repair: $2,500– $6,500
How to diagnose this on a 2022 Toyota Camry
-
Check transmission fluid level and condition
Transmission service procedures vary widely — some vehicles require a special procedure to check fluid level at operating temperature with the engine running. Follow the vehicle's specific procedure. Fluid that smells burnt or shows clutch material indicates internal damage; no point chasing the solenoid until the fluid is right.
Tools: Vehicle-specific service procedure, Replacement fluid (if needed)
-
Verify TCC command vs. actual lockup with a scan tool
During highway cruise, watch the TCC duty cycle or commanded state, alongside engine RPM and vehicle speed. The TCC should command on around 45–55 mph and engine RPM should drop 100–300 RPM at the moment of lockup. No RPM drop confirms the TCC is not engaging mechanically.
Tools: Scan tool with TCC and live RPM PIDs
-
Test the TCC solenoid electrically
Locate the TCC solenoid in the wiring diagram (most are accessible through the transmission's external connector). Measure resistance — typical 10–30 Ω depending on the transmission. Confirm continuity and that the TCM commands voltage to the solenoid during the lockup attempt.
Tools: Multimeter, Wiring diagram
-
Inspect transmission external connector for fluid
Disconnect the external transmission connector. Fluid wicking up into the wiring harness from a failed case seal will contaminate the TCM-side connector and cause electrical faults that mimic a solenoid failure. The repair is the seal and often the harness; the solenoid itself may be fine.
Tools: Connector unlock tool, Flashlight
-
Drop the pan and inspect the magnet
A pan magnet covered in fine clutch material — especially brown or black gritty paste — indicates the torque converter clutch has been slipping and shedding material. At that point the converter must be replaced; cleaning is not a fix.
Tools: Drain pan, Socket set, New filter and gasket
Known Technical Service Bulletins for the 2020-2024 Toyota Camry
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Toyota Camry.
- ENGINE Feb 26, 2026
OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.
NHTSA #11029896 - ELECTRICAL SYSTEM Jan 29, 2026
OBSOLETE NOTICE January 30, 2026: This bulletin is now obsolete. Please see T-SB-0001-26.
NHTSA #11028726 - ELECTRICAL SYSTEM Jan 27, 2026
Some 2018 – 2024 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.
NHTSA #11028722 - UNKNOWN OR OTHER Jan 6, 2026
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA #11028712 - ENGINE Aug 6, 2025
The specific condition covered by this program is for a small engine coolant leak that can occur from the flow shut-off valve that can allow coolant to drip on other parts of the vehicle. This can cause "Engine Maintenance Required" to be displayed on the instrument cluster or cause the A/C not to function normally. Although the flow shut-off valve is covered by Toyota’s New Vehicle Limited Warranty for 36 months or 36,000 miles (whichever comes first), we at Toyota care about the customers’ ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.
NHTSA #11022949 - ELECTRICAL SYSTEM Jun 24, 2025
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
NHTSA #11020670
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
Common fixes
- Service transmission fluid and filter to the correct specification
- Replace the TCC solenoid (often part of a solenoid pack)
- Repair external transmission wiring or connector
- Replace the torque converter (and usually rebuild the transmission)
- Rebuild or replace the transmission for severe internal damage
About the 2020-2024 Toyota Camry
The 2020-2024 Toyota Camry was commonly sold with the following powertrains: 2.5L I4, 3.5L V6, 2.5L Hybrid I4. Common trims include LE, SE, XLE, XSE.
How to tell solenoid failure from converter failure
Both produce P0741, but the symptoms differ slightly:
- Solenoid failure — RPM at cruise is exactly normal-plus-converter-slip (around 200–300 RPM high). The transmission shifts cleanly otherwise. No shudder.
- Converter slipping — RPM at cruise is variable and rises under load. Light-throttle cruise produces a shudder you can feel through the seat and the steering wheel — described by owners as “feels like driving over rumble strips.”
The shudder pattern is diagnostic: solenoid issues don’t shudder; worn TCC friction material shudders during partial lockup.
P0741 with shudder is a transmission job
Once the TCC friction lining is worn to the point of slipping under light load, the converter shedding material accelerates downstream wear in the transmission itself. Driving a P0741 with shudder for months can convert a $1,800 torque-converter-only repair into a $5,000+ rebuild. Treat shuddering P0741 as urgent.
Trans fluid changes after P0741 — proceed with caution
For decades the rule was “if the transmission is starting to fail, do NOT change the fluid — the new clean fluid washes out gunked clutch material and the transmission fails immediately.” Modern fluid technology has changed that advice. A drain-and-fill (not a flush) with the correct OEM fluid is now generally safe and sometimes resolves P0741 if the fluid was degraded. A full machine-flush on a transmission with TCC slip is still risky.