P0301 on a 2017 Ford Escape
Cylinder 1 Misfire
P0301 on a 2017 Ford Escape indicates cylinder 1 misfire. Stop driving and diagnose it before continuing — it can signal an unsafe condition. The most common cause is failed ignition coil on cylinder 1 (typically $80–$450). Confirm the root cause before replacing parts.
What does P0301 mean on a 2017 Ford Escape?
P0301 is set when the engine control module's misfire monitor detects that combustion is failing specifically in cylinder 1. The ECM identifies the affected cylinder by correlating crankshaft deceleration with camshaft position. The fact that only cylinder 1 is misfiring narrows the cause to parts that are specific to that cylinder — its plug, coil, injector, compression, or in some cases its harness wiring.
This guide covers P0301 across the 2015-2019 Ford Escape generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Ford Escape with P0301?
No. P0301 is a high-severity code on the 2017 Ford Escape — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.
What are the symptoms of P0301 on a 2017 Ford Escape?
- Check Engine Light steady or flashing depending on misfire severity
- Distinct rough idle that smooths out at higher RPM
- Stumble or hesitation under acceleration
- Reduced engine power
- Smell of unburned fuel from the exhaust
- Faint exhaust pop or backfire on overrun in severe cases
What causes P0301 on a 2017 Ford Escape?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed ignition coil on cylinder 1 On coil-on-plug engines this is the single most likely cause. | Most common | $80–$450 |
| Worn, fouled, or wrong-gap spark plug in cylinder 1 | Most common | $15–$80 |
| Clogged, leaking, or electrically failed injector on cylinder 1 | Common | $150–$800 |
| Burnt exhaust valve or low compression on cylinder 1 | Occasional | $800–$3,500 |
| Damaged or chafed wiring to the cylinder 1 coil or injector | Occasional | $80–$300 |
| Cracked cylinder 1 intake runner or local vacuum leak | Rare | $100–$600 |
How to diagnose this on a 2017 Ford Escape
-
Confirm cylinder 1 location on this engine
Cylinder 1 numbering differs by manufacturer. On most inline engines cylinder 1 is at the front. On most transverse V6s cylinder 1 is on the bank closer to the firewall. Consult the service manual before pulling parts.
Tools: Vehicle-specific service information
-
Swap the cylinder 1 ignition coil with a known-good cylinder
Move the cylinder 1 coil to cylinder 2 (or any non-misfiring cylinder), and move that coil to cylinder 1. Clear codes and drive. If the misfire follows the coil to its new cylinder, replace the coil. If the misfire stays in cylinder 1, the coil is fine.
Tools: Socket set
-
Swap the cylinder 1 spark plug
Use the same swap method with the spark plug. Inspect the removed plug first — a wet, fuel-soaked plug means no spark or no compression; a black sooty plug means a rich condition; a cracked ceramic means replace immediately.
Tools: Spark plug socket, Extension and ratchet
-
Test the cylinder 1 injector electrically and acoustically
Listen to the injector with a stethoscope at idle — it should click rhythmically. A "noid light" or scan tool fuel-injector test confirms that the ECM is firing the injector. If it pulses but the cylinder still misfires, the injector may be clogged or leaking.
Tools: Mechanic's stethoscope, Noid light kit or scan tool injector test
-
Perform a wet/dry compression test on cylinder 1
Measure compression on cylinder 1 cold and warm. If significantly lower than the other cylinders, add a teaspoon of oil through the plug hole and retest. Pressure that rises with oil points to worn rings; pressure that stays low points to valves or the head gasket.
Tools: Compression tester, Engine oil
Known Technical Service Bulletins for the 2015-2019 Ford Escape
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Ford Escape.
- UNKNOWN OR OTHER Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - STRUCTURE Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - ELECTRICAL SYSTEM Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - ELECTRICAL SYSTEM Nov 26, 2025
This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.
NHTSA #11025837 - POWER TRAIN Nov 11, 2025
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
NHTSA #11025611 - ELECTRICAL SYSTEM Nov 11, 2025
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
NHTSA #11025611
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
NHTSA complaints & recalls for the 2017 Ford Escape
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Ford Escape. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ford Escape diagnostics.
- ENGINE 1476
- ENGINE AND ENGINE COOLING 498
- POWER TRAIN 374
- ELECTRICAL SYSTEM 149
- UNKNOWN OR OTHER 146
3 active recalls
- VISIBILITY:POWER WINDOW DEVICES AND CONTROLS Aug 2016
Ford Motor Company (Ford) is recalling certain model year 2017 Ford Escape Titanium and SE vehicles manufactured October 5, 2015, to May 12, 2016. The settings for the closing-force of the power-operated windows may allow the windows to close on an object such as a body part and…
NHTSA campaign 16V617000 - POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL) Jun 2022
Ford Motor Company (Ford) is recalling certain 2013-2019 Escape, 2013-2018 C-Max, 2013-2016 Fusion, 2013-2021 Transit Connect, and 2015-2018 Edge vehicles. The bushing that attaches the shifter cable to the transmission may degrade or detach.…
NHTSA campaign 22V413000 - EQUIPMENT:ELECTRICAL:ENGINE BLOCK HEATER Jan 2026
Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.…
NHTSA campaign 26V011000
How do I fix P0301 on a 2017 Ford Escape?
- Replace the cylinder 1 ignition coil
- Replace all spark plugs (always replace as a complete set)
- Replace, clean, or service the cylinder 1 fuel injector
- Repair damaged harness wiring to cylinder 1
- Head work or engine rebuild for compression-related root causes
About the 2015-2019 Ford Escape
The 2015-2019 Ford Escape was commonly sold with the following powertrains: 1.5L EcoBoost I3, 2.0L EcoBoost I4, 2.5L Hybrid I4. Common trims include S, SE, SEL, Titanium.
Why isolated-cylinder misfires are easier than P0300 alone
When the ECM can attribute the misfire to one specific cylinder, the diagnostic path is short: there are only a handful of parts unique to that cylinder. The swap test (move the coil to a different cylinder, see if the misfire follows) typically resolves a P0301 within 15 minutes of hands-on work.
When P0301 follows a coil but the coil tests good
Aftermarket coils — especially the discount bulk packs sold online — can test fine on the bench but fail under cylinder-pressure load. If a brand-new coil sets P0301 within days, replace it with an OEM or premium-aftermarket part. This is especially common on Ford modular engines and GM L83/L86 truck V8s.
P0301 on a direct-injection engine
On direct-injection engines (most modern Hondas, Mazdas, Hyundais, and many Fords from 2012 onward), carbon buildup on intake valves can cause single-cylinder misfires that ignition and fuel work will not fix. A borescope inspection through the intake port reveals the carbon. Walnut-shell blasting restores normal operation.
P0301 on a 2017 Ford Escape: frequently asked questions
What does diagnostic trouble code P0301 mean on a 2017 Ford Escape?
P0301 is set when the engine control module's misfire monitor detects that combustion is failing specifically in cylinder 1. The ECM identifies the affected cylinder by correlating crankshaft deceleration with camshaft position. The fact that only cylinder 1 is misfiring narrows the cause to parts that are specific to that cylinder — its plug, coil, injector, compression, or in some cases its harness wiring.
What are the symptoms of P0301 on a 2017 Ford Escape?
Check Engine Light steady or flashing depending on misfire severity. Distinct rough idle that smooths out at higher RPM. Stumble or hesitation under acceleration. Reduced engine power. Smell of unburned fuel from the exhaust. Faint exhaust pop or backfire on overrun in severe cases
What causes P0301 on a 2017 Ford Escape?
Failed ignition coil on cylinder 1 (most-common). Worn, fouled, or wrong-gap spark plug in cylinder 1 (most-common). Clogged, leaking, or electrically failed injector on cylinder 1 (common). Burnt exhaust valve or low compression on cylinder 1 (occasional). Damaged or chafed wiring to the cylinder 1 coil or injector (occasional). Cracked cylinder 1 intake runner or local vacuum leak (rare)
Is it safe to drive a 2017 Ford Escape with P0301?
No. P0301 is a high-severity code on the 2017 Ford Escape — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.