P0440 on a 2017 Ford Escape
EVAP System Malfunction (Generic)
P0440 on a 2017 Ford Escape indicates evap system malfunction (generic). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is loose, worn, or wrong-spec fuel cap (typically $15–$60). Confirm the root cause before replacing parts.
What does P0440 mean on a 2017 Ford Escape?
P0440 is a generic evaporative emission (EVAP) system fault. The EVAP system captures fuel vapors from the tank and routes them through the charcoal canister to be burned by the engine instead of vented into the atmosphere. P0440 is set when the ECM detects that this sealed system has lost its ability to hold pressure or vacuum during a leak test. It is almost always the first sign of a small leak somewhere between the fuel tank and the engine intake.
This guide covers P0440 across the 2015-2019 Ford Escape generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Ford Escape with P0440?
In most cases a 2017 Ford Escape stays drivable for short trips with P0440 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0440 on a 2017 Ford Escape?
- Check Engine Light is illuminated
- Faint fuel smell when filling the tank or shortly after
- No drivability problem in most cases
- Fuel-cap warning light on some vehicles
- Vehicle will fail emissions / smog testing
What causes P0440 on a 2017 Ford Escape?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Loose, worn, or wrong-spec fuel cap Always the first thing to check — costs nothing to tighten or replace. | Most common | $15–$60 |
| Cracked, kinked, or disconnected EVAP hose | Common | $30–$200 |
| Failed EVAP purge valve (purge solenoid) stuck open or closed | Common | $80–$300 |
| Failed EVAP canister vent valve / vent solenoid | Common | $80–$350 |
| Cracked or damaged EVAP charcoal canister | Occasional | $200–$600 |
| Pinhole leak in fuel filler neck or tank seam | Occasional | $150–$800 |
| Failed fuel tank pressure sensor | Occasional | $100–$350 |
How to diagnose this on a 2017 Ford Escape
-
Inspect and re-seat the fuel cap
Remove the fuel cap and check the rubber gasket for damage, debris, or twisting. Reinstall hand-tight until the cap clicks. Many vehicles require 3+ click stops. Clear the code and drive several drive cycles to allow the EVAP monitor to retest.
Tools: None
-
Read mode 6 / EVAP monitor data
Pull mode 6 test results for the EVAP system. Look at the small-leak, large-leak, and purge flow test IDs. The specific test that failed narrows the diagnosis from "EVAP system" to which subsystem within it.
Tools: Scan tool with mode 6 support
-
Smoke-test the EVAP system
Introduce low-pressure smoke (typically 0.5 psi) into the EVAP service port. Inspect every hose joint, the charcoal canister, the purge and vent solenoids, the filler neck, and the tank top. Smoke escaping anywhere is the leak — repair it and retest.
Tools: EVAP smoke machine, UV dye and light (optional), Inspection mirror
-
Bench-test the purge valve and vent valve
Remove the purge valve and apply 12 V across its terminals. It should click and open. With no voltage, it should hold vacuum. The vent valve operates in reverse — normally open, closes when energized. Either valve stuck the wrong way will set P0440.
Tools: 12 V test source, Hand vacuum pump
-
Check the fuel tank pressure sensor reading
Compare the live tank pressure PID to a known-good vehicle. A reading that does not change when the cap is removed or when the purge valve is commanded indicates either a failed sensor or a blocked hose to it.
Tools: Scan tool
Known Technical Service Bulletins for the 2015-2019 Ford Escape
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Ford Escape.
- UNKNOWN OR OTHER Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - STRUCTURE Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - ELECTRICAL SYSTEM Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - ELECTRICAL SYSTEM Nov 26, 2025
This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.
NHTSA #11025837 - POWER TRAIN Nov 11, 2025
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
NHTSA #11025611 - ELECTRICAL SYSTEM Nov 11, 2025
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
NHTSA #11025611
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
NHTSA complaints & recalls for the 2017 Ford Escape
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Ford Escape. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ford Escape diagnostics.
- ENGINE 1476
- ENGINE AND ENGINE COOLING 498
- POWER TRAIN 374
- ELECTRICAL SYSTEM 149
- UNKNOWN OR OTHER 146
3 active recalls
- VISIBILITY:POWER WINDOW DEVICES AND CONTROLS Aug 2016
Ford Motor Company (Ford) is recalling certain model year 2017 Ford Escape Titanium and SE vehicles manufactured October 5, 2015, to May 12, 2016. The settings for the closing-force of the power-operated windows may allow the windows to close on an object such as a body part and…
NHTSA campaign 16V617000 - POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL) Jun 2022
Ford Motor Company (Ford) is recalling certain 2013-2019 Escape, 2013-2018 C-Max, 2013-2016 Fusion, 2013-2021 Transit Connect, and 2015-2018 Edge vehicles. The bushing that attaches the shifter cable to the transmission may degrade or detach.…
NHTSA campaign 22V413000 - EQUIPMENT:ELECTRICAL:ENGINE BLOCK HEATER Jan 2026
Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.…
NHTSA campaign 26V011000
How do I fix P0440 on a 2017 Ford Escape?
- Replace the fuel cap with an OEM spec part
- Replace cracked or aged EVAP hoses
- Replace the EVAP purge valve
- Replace the EVAP vent valve / vent solenoid
- Replace the EVAP charcoal canister
About the 2015-2019 Ford Escape
The 2015-2019 Ford Escape was commonly sold with the following powertrains: 1.5L EcoBoost I3, 2.0L EcoBoost I4, 2.5L Hybrid I4. Common trims include S, SE, SEL, Titanium.
P0440 vs the more specific EVAP codes
P0440 is the catch-all. If the ECM can identify the type of failure more specifically, it will set a narrower code: P0442 (small leak), P0455 (large leak), P0446 (vent control), and so on. Older vehicles often set P0440 when newer vehicles would set one of the more specific codes for the same underlying condition.
Why the gas cap is always step one
A loose or damaged gas cap accounts for roughly one-third of all P0440 set events. The cap is the cheapest part to replace and the most common point of failure. Always tighten until you hear 3+ clicks, and replace any cap whose gasket shows cracks or hardening.
How long after a repair until the code clears
The EVAP leak test only runs under specific conditions: cold soak (engine off for several hours), partial fuel tank (typically 25–75 % full), and a specific outside temperature range. After a repair, expect 2–4 drive cycles before the monitor completes and the readiness flag turns “ready.” Clearing the code with a scan tool removes the light immediately, but the monitor must complete naturally before emissions testing will pass.
P0440 on a 2017 Ford Escape: frequently asked questions
What does diagnostic trouble code P0440 mean on a 2017 Ford Escape?
P0440 is a generic evaporative emission (EVAP) system fault. The EVAP system captures fuel vapors from the tank and routes them through the charcoal canister to be burned by the engine instead of vented into the atmosphere. P0440 is set when the ECM detects that this sealed system has lost its ability to hold pressure or vacuum during a leak test. It is almost always the first sign of a small leak somewhere between the fuel tank and the engine intake.
What are the symptoms of P0440 on a 2017 Ford Escape?
Check Engine Light is illuminated. Faint fuel smell when filling the tank or shortly after. No drivability problem in most cases. Fuel-cap warning light on some vehicles. Vehicle will fail emissions / smog testing
What causes P0440 on a 2017 Ford Escape?
Loose, worn, or wrong-spec fuel cap (most-common). Cracked, kinked, or disconnected EVAP hose (common). Failed EVAP purge valve (purge solenoid) stuck open or closed (common). Failed EVAP canister vent valve / vent solenoid (common). Cracked or damaged EVAP charcoal canister (occasional). Pinhole leak in fuel filler neck or tank seam (occasional). Failed fuel tank pressure sensor (occasional)
Is it safe to drive a 2017 Ford Escape with P0440?
In most cases a 2017 Ford Escape stays drivable for short trips with P0440 active, but it should be diagnosed and repaired promptly — this is a low-severity code. Ignoring it can lead to further damage or a failed emissions test.