P0442 on a 2022 Toyota Camry
EVAP Small Leak Detected
What does P0442 mean on a 2022 Toyota Camry?
P0442 is set when the EVAP system's small-leak monitor detects an opening approximately 0.040 inches (1.0 mm) or larger. This is the equivalent of the gas cap being left slightly loose or a small crack in a vent hose. The vehicle remains fully drivable and consumes no extra fuel, but the EVAP system can no longer hold the sealed vacuum required for compliance.
Symptoms on a 2022 Toyota Camry
- Check Engine Light is illuminated
- Faint fuel smell, especially after refueling on a hot day
- No noticeable change in drivability or fuel economy
- Vehicle will fail emissions / smog testing
Likely causes on a 2022 Toyota Camry
- Loose, worn, or cross-threaded fuel cap Most commonEstimated repair: $15– $60
- Aged or split EVAP hose CommonEstimated repair: $30– $200
- Failing purge or vent valve seal CommonEstimated repair: $80– $350
- Cracked EVAP charcoal canister OccasionalEstimated repair: $200– $600
- Damaged O-rings at hose-to-canister or hose-to-solenoid connections OccasionalEstimated repair: $20– $120
- Pinhole or seam leak in the fuel filler neck OccasionalEstimated repair: $150– $600
- Failed fuel tank vent at the tank top (less accessible to inspect) RareEstimated repair: $300– $900
How to diagnose this on a 2022 Toyota Camry
-
Tighten or replace the fuel cap
Remove and reinstall the fuel cap to at least three clicks. Inspect the rubber gasket for cracks, debris, or compression set. Replace with an OEM-spec cap if the gasket is damaged or the cap is more than 8 years old.
Tools: None
-
Smoke-test the EVAP system
A 0.040-inch leak is too small to find by ear and almost always too small to see visually without smoke. Pressurize the EVAP system with smoke at the service port and trace the smoke trail to its source. Common leak points: behind the rear bumper near the canister, the hose between purge valve and intake, and the top of the fuel tank.
Tools: EVAP smoke machine, UV dye (optional), Inspection mirror and flashlight
-
Inspect the EVAP service port itself
The green EVAP service port cap is a frequent leak point because its O-ring hardens and fails after years of heat cycles. With smoke already in the system, watch the service port specifically.
Tools: Inspection mirror
-
Visually inspect the charcoal canister
Many trucks and SUVs mount the canister behind the rear axle where it is exposed to road debris and salt spray. Cracks in the plastic housing are common on aging vehicles. Replace the canister if cracked or saturated.
Tools: Floor jack and stands, Trim panel tools
-
Verify monitor completion before re-testing
After repair, drive 2–4 cold-start drive cycles with the tank between 25 % and 75 % full. Use a scan tool to confirm the EVAP readiness flag turns "ready." Clearing the code prematurely will set the light again as soon as the monitor runs.
Tools: Scan tool with readiness monitor display
Known Technical Service Bulletins for the 2020-2024 Toyota Camry
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Toyota Camry.
- ENGINE Feb 26, 2026
OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.
NHTSA #11029896 - ELECTRICAL SYSTEM Jan 29, 2026
OBSOLETE NOTICE January 30, 2026: This bulletin is now obsolete. Please see T-SB-0001-26.
NHTSA #11028726 - ELECTRICAL SYSTEM Jan 27, 2026
Some 2018 – 2024 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.
NHTSA #11028722 - UNKNOWN OR OTHER Jan 6, 2026
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA #11028712 - ENGINE Aug 6, 2025
The specific condition covered by this program is for a small engine coolant leak that can occur from the flow shut-off valve that can allow coolant to drip on other parts of the vehicle. This can cause "Engine Maintenance Required" to be displayed on the instrument cluster or cause the A/C not to function normally. Although the flow shut-off valve is covered by Toyota’s New Vehicle Limited Warranty for 36 months or 36,000 miles (whichever comes first), we at Toyota care about the customers’ ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.
NHTSA #11022949 - ELECTRICAL SYSTEM Jun 24, 2025
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
NHTSA #11020670
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
Common fixes
- Replace the fuel cap
- Replace cracked EVAP hoses and aged O-rings
- Replace the EVAP purge valve or vent valve
- Replace the charcoal canister assembly
- Replace the fuel filler neck (rust or pinhole)
About the 2020-2024 Toyota Camry
The 2020-2024 Toyota Camry was commonly sold with the following powertrains: 2.5L I4, 3.5L V6, 2.5L Hybrid I4. Common trims include LE, SE, XLE, XSE.
P0442 vs P0455 vs P0456
The three EVAP leak codes describe the same kind of fault at different leak sizes:
| Code | Leak size threshold | Typical real-world cause |
|---|---|---|
| P0456 | ~0.020” (very small) | Cap O-ring, fresh hose pinhole |
| P0442 | ~0.040” (small) | Loose cap, aging hose, cracked vent valve seal |
| P0455 | ~0.090”+ (large or no seal) | Missing cap, disconnected hose, large canister crack |
A vehicle that sets P0456 today often sets P0442 in a few months as the same crack grows.
Why smoke testing is non-negotiable
EVAP leaks are usually too small to find any other way. A bare-eye inspection of every hose and joint will miss most P0442 causes. The smoke machine is a one-time tool purchase (or one-time shop diagnostic fee) that pays for itself on the first EVAP repair.
What “0.040 inch leak” actually means
OBD-II EVAP monitors do not measure the leak directly. They apply a calibrated vacuum or pressure to the sealed system and time how quickly it bleeds off. The leak-equivalent diameter is calculated from that decay rate. A real-world 0.040” hole and a 0.030” hole with a smaller restriction upstream can produce the same monitor result.