P0442 on a 2017 Toyota Camry
EVAP Small Leak Detected
What does P0442 mean on a 2017 Toyota Camry?
P0442 is set when the EVAP system's small-leak monitor detects an opening approximately 0.040 inches (1.0 mm) or larger. This is the equivalent of the gas cap being left slightly loose or a small crack in a vent hose. The vehicle remains fully drivable and consumes no extra fuel, but the EVAP system can no longer hold the sealed vacuum required for compliance.
Symptoms on a 2017 Toyota Camry
- Check Engine Light is illuminated
- Faint fuel smell, especially after refueling on a hot day
- No noticeable change in drivability or fuel economy
- Vehicle will fail emissions / smog testing
Likely causes on a 2017 Toyota Camry
- Loose, worn, or cross-threaded fuel cap Most commonEstimated repair: $15– $60
- Aged or split EVAP hose CommonEstimated repair: $30– $200
- Failing purge or vent valve seal CommonEstimated repair: $80– $350
- Cracked EVAP charcoal canister OccasionalEstimated repair: $200– $600
- Damaged O-rings at hose-to-canister or hose-to-solenoid connections OccasionalEstimated repair: $20– $120
- Pinhole or seam leak in the fuel filler neck OccasionalEstimated repair: $150– $600
- Failed fuel tank vent at the tank top (less accessible to inspect) RareEstimated repair: $300– $900
How to diagnose this on a 2017 Toyota Camry
-
Tighten or replace the fuel cap
Remove and reinstall the fuel cap to at least three clicks. Inspect the rubber gasket for cracks, debris, or compression set. Replace with an OEM-spec cap if the gasket is damaged or the cap is more than 8 years old.
Tools: None
-
Smoke-test the EVAP system
A 0.040-inch leak is too small to find by ear and almost always too small to see visually without smoke. Pressurize the EVAP system with smoke at the service port and trace the smoke trail to its source. Common leak points: behind the rear bumper near the canister, the hose between purge valve and intake, and the top of the fuel tank.
Tools: EVAP smoke machine, UV dye (optional), Inspection mirror and flashlight
-
Inspect the EVAP service port itself
The green EVAP service port cap is a frequent leak point because its O-ring hardens and fails after years of heat cycles. With smoke already in the system, watch the service port specifically.
Tools: Inspection mirror
-
Visually inspect the charcoal canister
Many trucks and SUVs mount the canister behind the rear axle where it is exposed to road debris and salt spray. Cracks in the plastic housing are common on aging vehicles. Replace the canister if cracked or saturated.
Tools: Floor jack and stands, Trim panel tools
-
Verify monitor completion before re-testing
After repair, drive 2–4 cold-start drive cycles with the tank between 25 % and 75 % full. Use a scan tool to confirm the EVAP readiness flag turns "ready." Clearing the code prematurely will set the light again as soon as the monitor runs.
Tools: Scan tool with readiness monitor display
Known Technical Service Bulletins for the 2015-2019 Toyota Camry
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Toyota Camry.
- ENGINE Feb 12, 2026
This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing a rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger.
NHTSA #11029893 - ENGINE Feb 12, 2026
OBSOLETE NOTICE February 13, 2026: This bulletin is now obsolete. Please see T-SB-0009-26.
NHTSA #11029892 - UNKNOWN OR OTHER Jan 6, 2026
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA #11028712 - ELECTRICAL SYSTEM Jun 12, 2025
The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.
NHTSA #11020657 - STRUCTURE Dec 5, 2024
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
NHTSA #11012743 - STRUCTURE Dec 5, 2024
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
NHTSA #11012744
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
Common fixes
- Replace the fuel cap
- Replace cracked EVAP hoses and aged O-rings
- Replace the EVAP purge valve or vent valve
- Replace the charcoal canister assembly
- Replace the fuel filler neck (rust or pinhole)
About the 2015-2019 Toyota Camry
The 2015-2019 Toyota Camry was commonly sold with the following powertrains: 2.5L I4, 3.5L V6, 2.5L Hybrid I4. Common trims include LE, SE, XLE, XSE.
P0442 vs P0455 vs P0456
The three EVAP leak codes describe the same kind of fault at different leak sizes:
| Code | Leak size threshold | Typical real-world cause |
|---|---|---|
| P0456 | ~0.020” (very small) | Cap O-ring, fresh hose pinhole |
| P0442 | ~0.040” (small) | Loose cap, aging hose, cracked vent valve seal |
| P0455 | ~0.090”+ (large or no seal) | Missing cap, disconnected hose, large canister crack |
A vehicle that sets P0456 today often sets P0442 in a few months as the same crack grows.
Why smoke testing is non-negotiable
EVAP leaks are usually too small to find any other way. A bare-eye inspection of every hose and joint will miss most P0442 causes. The smoke machine is a one-time tool purchase (or one-time shop diagnostic fee) that pays for itself on the first EVAP repair.
What “0.040 inch leak” actually means
OBD-II EVAP monitors do not measure the leak directly. They apply a calibrated vacuum or pressure to the sealed system and time how quickly it bleeds off. The leak-equivalent diameter is calculated from that decay rate. A real-world 0.040” hole and a 0.030” hole with a smaller restriction upstream can produce the same monitor result.