P0455 on a 2017 Toyota Camry
EVAP Large or Gross Leak Detected
What does P0455 mean on a 2017 Toyota Camry?
P0455 is set when the EVAP system's gross-leak monitor detects an opening approximately 0.090 inches (2.3 mm) or larger — or in many cases, no seal at all. This is the size of a missing gas cap, a disconnected hose, or a failed vent solenoid stuck open. The system cannot hold pressure or vacuum for the calibration period, so the ECM concludes a major leak.
Symptoms on a 2017 Toyota Camry
- Check Engine Light is illuminated
- Distinct fuel smell, especially after refueling
- Fuel-cap warning message on the dashboard on some vehicles
- No drivability issue
- Vehicle will fail emissions / smog testing
Likely causes on a 2017 Toyota Camry
- Missing, loose, or wrong-fit fuel cap Most commonEstimated repair: $0– $60
Always check first. A locking gas cap from another vehicle that almost fits is a common source.
- Disconnected or split EVAP hose CommonEstimated repair: $30– $200
- EVAP vent valve stuck open (will not seal during the monitor test) CommonEstimated repair: $80– $350
- Damaged or rusted-through fuel filler neck OccasionalEstimated repair: $200– $700
- Cracked or broken EVAP charcoal canister OccasionalEstimated repair: $200– $600
- Damaged O-ring at the fuel pump assembly cover RareEstimated repair: $30– $500
- Rodent damage to EVAP hoses (parked vehicles) OccasionalEstimated repair: $30– $200
How to diagnose this on a 2017 Toyota Camry
-
Check the gas cap is present and correctly seated
Confirm the cap is the correct OEM cap for the vehicle. Many generic-fit replacement caps look identical but have slightly wrong gasket geometry. Hand-tighten to at least 3 clicks. Some vehicles flag a missing cap as P0455 within one drive cycle.
Tools: None
-
Visually inspect the EVAP hoses near the canister
On most trucks and SUVs the EVAP canister sits behind the rear bumper or above the rear axle. Inspect every hose from the canister to the tank vent and to the purge solenoid. Pay particular attention to rodent damage on parked vehicles.
Tools: Floor jack and stands, Flashlight
-
Smoke-test the EVAP system at low pressure
Introduce smoke at 0.5 psi through the service port. With a large leak the smoke will pour visibly from the failure point within seconds. If smoke escapes from the vent solenoid even with the solenoid commanded closed, replace the solenoid.
Tools: EVAP smoke machine
-
Test the EVAP vent valve function
Disconnect the vent valve and apply 12 V — it should click and close. Hold a hand vacuum pump to one port and verify the valve holds vacuum when energized. A vent valve that does not close fully will set P0455 because the system can never seal.
Tools: 12 V test source, Hand vacuum pump
-
Inspect the fuel filler neck and tank-top seals
Rust-belt vehicles often develop pinholes or seam separation in the metal portion of the fuel filler neck. Once the rust is through, the EVAP system cannot hold any vacuum. Replacement is the only fix.
Tools: Floor jack and stands, Inspection mirror
Known Technical Service Bulletins for the 2015-2019 Toyota Camry
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Toyota Camry.
- ENGINE Feb 12, 2026
This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing a rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger.
NHTSA #11029893 - ENGINE Feb 12, 2026
OBSOLETE NOTICE February 13, 2026: This bulletin is now obsolete. Please see T-SB-0009-26.
NHTSA #11029892 - UNKNOWN OR OTHER Jan 6, 2026
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA #11028712 - ELECTRICAL SYSTEM Jun 12, 2025
The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.
NHTSA #11020657 - STRUCTURE Dec 5, 2024
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
NHTSA #11012743 - STRUCTURE Dec 5, 2024
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
NHTSA #11012744
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
Common fixes
- Replace the fuel cap
- Replace the EVAP vent valve / vent solenoid
- Replace damaged EVAP hoses
- Replace the EVAP charcoal canister
- Replace the fuel filler neck
About the 2015-2019 Toyota Camry
The 2015-2019 Toyota Camry was commonly sold with the following powertrains: 2.5L I4, 3.5L V6, 2.5L Hybrid I4. Common trims include LE, SE, XLE, XSE.
How fast P0455 sets after a missing cap
Most OBD-II vehicles flag P0455 within one cold-start drive cycle after the cap is left off. Some Ford and GM vehicles will set a more specific “check fuel cap” message first and only escalate to P0455 if the issue persists across multiple drive cycles.
P0455 right after winter on a parked vehicle
Mice and rats chew EVAP hoses to nest inside the canister or near the fuel tank. If P0455 appears on a vehicle that has been parked for the winter, inspect every accessible EVAP hose for clean-edged bite marks before buying parts. This pattern is so common on rural-parked trucks that several shop forums have dedicated threads.
The cap that “fits” but doesn’t seal
A locking gas cap from a similar-vintage vehicle in the same brand family often threads on but seals against the filler neck at the wrong depth or angle. The result is repeated P0455 codes after every refuel. If the cap has been replaced and the code persists, double-check it is the exact OEM part number for this vehicle.