P0325 on a 2017 Ford Escape
Knock Sensor 1 Circuit Fault
P0325 on a 2017 Ford Escape indicates knock sensor 1 circuit fault. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed knock sensor element (typically $150–$600). Confirm the root cause before replacing parts.
What does P0325 mean on a 2017 Ford Escape?
P0325 is set when the engine control module does not receive a valid signal from the Bank 1 knock sensor — or the only knock sensor on engines that use one. The knock sensor is a piezoelectric vibration sensor that listens for the characteristic frequency of pre-ignition (detonation) so the ECM can pull timing to protect the engine. With no usable knock signal, the ECM defaults to conservative timing maps, which reduces power and fuel economy.
This guide covers P0325 across the 2015-2019 Ford Escape generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Ford Escape with P0325?
In most cases a 2017 Ford Escape stays drivable for short trips with P0325 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0325 on a 2017 Ford Escape?
- Check Engine Light is illuminated
- Reduced power and slower throttle response
- Slight reduction in fuel economy
- Engine may run cooler than normal under load
- Possible audible engine ping or knock under hard acceleration
- No drivability issue in normal driving
What causes P0325 on a 2017 Ford Escape?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed knock sensor element Most common at 100k+ miles. Some engines bury the sensor under the intake. | Most common | $150–$600 |
| Damaged or corroded knock sensor wiring or connector | Common | $80–$350 |
| Loose knock sensor mounting (sensor must be torqued correctly to "hear") | Common | $20–$100 |
| Rodent damage to knock sensor harness (parked vehicles) | Occasional | $80–$350 |
| Failed knock sensor sub-harness on GM L83/L86 truck V8s Specific to GM 5.3 / 6.2 truck V8s — well-documented sub-harness failure. | Occasional | $200–$600 |
| Internal engine damage producing noise outside the knock sensor band | Rare | $2,000–$6,000 |
How to diagnose this on a 2017 Ford Escape
-
Locate the knock sensor — often under the intake manifold
On many engines (notably GM V6 + V8 truck engines, Toyota 2GR-FE, and most modern Hondas) the knock sensor sits in the engine valley under the intake manifold. Knowing this before starting saves a wasted hour of looking. Consult the service manual.
Tools: Vehicle-specific service information
-
Test knock sensor resistance
Unplug the sensor and measure resistance with a multimeter. Most knock sensors read approximately 90 kΩ to 2.5 MΩ depending on style. Infinite resistance (open) or near-zero (short) confirms a failed sensor.
Tools: Multimeter, Service spec sheet
-
Inspect the wiring and connector
Knock sensor harnesses run close to hot exhaust components and are common chafing victims. Inspect every inch of the harness from the sensor to the PCM connector. Repair any visible damage before replacing the sensor.
Tools: Inspection mirror, Flashlight, Wire repair supplies
-
Verify torque specification on the existing sensor
A knock sensor mounted with the wrong torque cannot transmit vibration efficiently. Spec is typically 15–25 ft-lb. Use a torque wrench, not "tight by feel." Over-torque can crack the housing; under-torque produces false knock-sensor codes.
Tools: Torque wrench, Service spec sheet
-
Check for GM-specific sub-harness failure
On GM L83 (5.3 V8) and L86 (6.2 V8) truck engines, the knock sensor sub-harness running under the intake manifold is a documented failure point — the harness chafes and shorts. Replacement requires intake manifold removal. The sub-harness itself is inexpensive but the labor is significant.
Tools: Intake manifold gasket, Common hand tools
Known Technical Service Bulletins for the 2015-2019 Ford Escape
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Ford Escape.
- UNKNOWN OR OTHER Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - STRUCTURE Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - ELECTRICAL SYSTEM Feb 23, 2026
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
NHTSA #11029052 - ELECTRICAL SYSTEM Nov 26, 2025
This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.
NHTSA #11025837 - POWER TRAIN Nov 11, 2025
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
NHTSA #11025611 - ELECTRICAL SYSTEM Nov 11, 2025
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
NHTSA #11025611
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
NHTSA complaints & recalls for the 2017 Ford Escape
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Ford Escape. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ford Escape diagnostics.
- ENGINE 1476
- ENGINE AND ENGINE COOLING 498
- POWER TRAIN 374
- ELECTRICAL SYSTEM 149
- UNKNOWN OR OTHER 146
3 active recalls
- VISIBILITY:POWER WINDOW DEVICES AND CONTROLS Aug 2016
Ford Motor Company (Ford) is recalling certain model year 2017 Ford Escape Titanium and SE vehicles manufactured October 5, 2015, to May 12, 2016. The settings for the closing-force of the power-operated windows may allow the windows to close on an object such as a body part and…
NHTSA campaign 16V617000 - POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL) Jun 2022
Ford Motor Company (Ford) is recalling certain 2013-2019 Escape, 2013-2018 C-Max, 2013-2016 Fusion, 2013-2021 Transit Connect, and 2015-2018 Edge vehicles. The bushing that attaches the shifter cable to the transmission may degrade or detach.…
NHTSA campaign 22V413000 - EQUIPMENT:ELECTRICAL:ENGINE BLOCK HEATER Jan 2026
Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.…
NHTSA campaign 26V011000
How do I fix P0325 on a 2017 Ford Escape?
- Replace the knock sensor with an OEM part
- Replace the knock sensor sub-harness (GM L83/L86)
- Repair damaged wiring to the knock sensor
- Re-torque the sensor to OEM specification
About the 2015-2019 Ford Escape
The 2015-2019 Ford Escape was commonly sold with the following powertrains: 1.5L EcoBoost I3, 2.0L EcoBoost I4, 2.5L Hybrid I4. Common trims include S, SE, SEL, Titanium.
Why P0325 is a “common” code on GM V8 trucks
GM L83 (5.3L) and L86 (6.2L) Gen V V8 engines — used in 2014+ Silverado, Sierra, Tahoe, Yukon, Suburban, and Escalade — have a well-documented knock sensor sub-harness failure. The harness chafes against the intake valley pan and eventually shorts. P0325 + P0330 setting together on these engines is so common that aftermarket “extended” sub-harnesses are sold specifically to relocate the wiring away from the chafe point.
If you have one of these vehicles, expect this repair around 80–130k miles. Plan it with the next intake manifold service.
What the ECM does without a working knock sensor
The engine still runs — but conservatively. The ECM uses “open-loop” ignition timing maps that pull 3–6 degrees of advance out of every cell, sacrificing power and fuel economy to ensure no detonation. Expect 1–2 MPG lower and noticeably slower throttle response.
Knock sensor diagnostics with a scope
The knock sensor is essentially a microphone. Tapping the cylinder block near the sensor with a screwdriver while watching the scan-tool knock count PID should produce hits. No response to tapping confirms a dead sensor or open wiring even if the multimeter resistance looks correct.
P0325 on a 2017 Ford Escape: frequently asked questions
What does diagnostic trouble code P0325 mean on a 2017 Ford Escape?
P0325 is set when the engine control module does not receive a valid signal from the Bank 1 knock sensor — or the only knock sensor on engines that use one. The knock sensor is a piezoelectric vibration sensor that listens for the characteristic frequency of pre-ignition (detonation) so the ECM can pull timing to protect the engine. With no usable knock signal, the ECM defaults to conservative timing maps, which reduces power and fuel economy.
What are the symptoms of P0325 on a 2017 Ford Escape?
Check Engine Light is illuminated. Reduced power and slower throttle response. Slight reduction in fuel economy. Engine may run cooler than normal under load. Possible audible engine ping or knock under hard acceleration. No drivability issue in normal driving
What causes P0325 on a 2017 Ford Escape?
Failed knock sensor element (most-common). Damaged or corroded knock sensor wiring or connector (common). Loose knock sensor mounting (sensor must be torqued correctly to "hear") (common). Rodent damage to knock sensor harness (parked vehicles) (occasional). Failed knock sensor sub-harness on GM L83/L86 truck V8s (occasional). Internal engine damage producing noise outside the knock sensor band (rare)
Is it safe to drive a 2017 Ford Escape with P0325?
In most cases a 2017 Ford Escape stays drivable for short trips with P0325 active, but it should be diagnosed and repaired promptly — this is a moderate-severity code. Ignoring it can lead to further damage or a failed emissions test.