P0301 on a 2022 Ford Bronco
Cylinder 1 Misfire
P0301 on a 2022 Ford Bronco indicates cylinder 1 misfire. Stop driving and diagnose it before continuing — it can signal an unsafe condition. The most common cause is failed ignition coil on cylinder 1 (typically $80–$450). Confirm the root cause before replacing parts.
What does P0301 mean on a 2022 Ford Bronco?
P0301 is set when the engine control module's misfire monitor detects that combustion is failing specifically in cylinder 1. The ECM identifies the affected cylinder by correlating crankshaft deceleration with camshaft position. The fact that only cylinder 1 is misfiring narrows the cause to parts that are specific to that cylinder — its plug, coil, injector, compression, or in some cases its harness wiring.
This guide covers P0301 across the 2020-2024 Ford Bronco generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Ford Bronco with P0301?
No. P0301 is a high-severity code on the 2022 Ford Bronco — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.
What are the symptoms of P0301 on a 2022 Ford Bronco?
- Check Engine Light steady or flashing depending on misfire severity
- Distinct rough idle that smooths out at higher RPM
- Stumble or hesitation under acceleration
- Reduced engine power
- Smell of unburned fuel from the exhaust
- Faint exhaust pop or backfire on overrun in severe cases
What causes P0301 on a 2022 Ford Bronco?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed ignition coil on cylinder 1 On coil-on-plug engines this is the single most likely cause. | Most common | $80–$450 |
| Worn, fouled, or wrong-gap spark plug in cylinder 1 | Most common | $15–$80 |
| Clogged, leaking, or electrically failed injector on cylinder 1 | Common | $150–$800 |
| Burnt exhaust valve or low compression on cylinder 1 | Occasional | $800–$3,500 |
| Damaged or chafed wiring to the cylinder 1 coil or injector | Occasional | $80–$300 |
| Cracked cylinder 1 intake runner or local vacuum leak | Rare | $100–$600 |
How to diagnose this on a 2022 Ford Bronco
-
Confirm cylinder 1 location on this engine
Cylinder 1 numbering differs by manufacturer. On most inline engines cylinder 1 is at the front. On most transverse V6s cylinder 1 is on the bank closer to the firewall. Consult the service manual before pulling parts.
Tools: Vehicle-specific service information
-
Swap the cylinder 1 ignition coil with a known-good cylinder
Move the cylinder 1 coil to cylinder 2 (or any non-misfiring cylinder), and move that coil to cylinder 1. Clear codes and drive. If the misfire follows the coil to its new cylinder, replace the coil. If the misfire stays in cylinder 1, the coil is fine.
Tools: Socket set
-
Swap the cylinder 1 spark plug
Use the same swap method with the spark plug. Inspect the removed plug first — a wet, fuel-soaked plug means no spark or no compression; a black sooty plug means a rich condition; a cracked ceramic means replace immediately.
Tools: Spark plug socket, Extension and ratchet
-
Test the cylinder 1 injector electrically and acoustically
Listen to the injector with a stethoscope at idle — it should click rhythmically. A "noid light" or scan tool fuel-injector test confirms that the ECM is firing the injector. If it pulses but the cylinder still misfires, the injector may be clogged or leaking.
Tools: Mechanic's stethoscope, Noid light kit or scan tool injector test
-
Perform a wet/dry compression test on cylinder 1
Measure compression on cylinder 1 cold and warm. If significantly lower than the other cylinders, add a teaspoon of oil through the plug hole and retest. Pressure that rises with oil points to worn rings; pressure that stays low points to valves or the head gasket.
Tools: Compression tester, Engine oil
NHTSA complaints & recalls for the 2022 Ford Bronco
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Ford Bronco. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ford Bronco diagnostics.
- ENGINE 42
- POWER TRAIN 34
- VISIBILITY/WIPER 64
- SERVICE BRAKES 41
- UNKNOWN OR OTHER 37
21 active recalls
- LATCHES/LOCKS/LINKAGES:DOORS:LOCK Jun 2022
Ford Motor Company (Ford) is recalling certain four-door 2021-2022 Bronco vehicles. The passenger-side rear door may be opened from inside of the vehicle when the child safety lock is in the "ON" position.…
NHTSA campaign 22V411000 - VISIBILITY:WINDSHIELD Jun 2022
Ford Motor Company (Ford) is recalling certain 2022 Bronco and Ranger vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle…
NHTSA campaign 22V451000 - BACK OVER PREVENTION: SENSING SYSTEM: CAMERA Nov 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requireme…
NHTSA campaign 22V825000 - AIR BAGS:SENSOR:SIDE IMPACT Dec 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The right or left side impact sensors may not be properly secured to the vehicle.…
NHTSA campaign 22V928000
How do I fix P0301 on a 2022 Ford Bronco?
- Replace the cylinder 1 ignition coil
- Replace all spark plugs (always replace as a complete set)
- Replace, clean, or service the cylinder 1 fuel injector
- Repair damaged harness wiring to cylinder 1
- Head work or engine rebuild for compression-related root causes
About the 2020-2024 Ford Bronco
The 2020-2024 Ford Bronco was commonly sold with the following powertrains: 2.3L EcoBoost I4, 2.7L EcoBoost V6. Common trims include Base, Big Bend, Black Diamond, Outer Banks, Badlands, Wildtrak, Raptor.
Why isolated-cylinder misfires are easier than P0300 alone
When the ECM can attribute the misfire to one specific cylinder, the diagnostic path is short: there are only a handful of parts unique to that cylinder. The swap test (move the coil to a different cylinder, see if the misfire follows) typically resolves a P0301 within 15 minutes of hands-on work.
When P0301 follows a coil but the coil tests good
Aftermarket coils — especially the discount bulk packs sold online — can test fine on the bench but fail under cylinder-pressure load. If a brand-new coil sets P0301 within days, replace it with an OEM or premium-aftermarket part. This is especially common on Ford modular engines and GM L83/L86 truck V8s.
P0301 on a direct-injection engine
On direct-injection engines (most modern Hondas, Mazdas, Hyundais, and many Fords from 2012 onward), carbon buildup on intake valves can cause single-cylinder misfires that ignition and fuel work will not fix. A borescope inspection through the intake port reveals the carbon. Walnut-shell blasting restores normal operation.