P0743 on a 2022 Kia Forte
Torque Converter Clutch Circuit Electrical Fault
P0743 on a 2022 Kia Forte indicates torque converter clutch circuit electrical fault. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed tcc solenoid (open or shorted coil) (typically $300–$900). Confirm the root cause before replacing parts.
What does P0743 mean on a 2022 Kia Forte?
P0743 narrows the torque converter clutch fault to the electrical circuit specifically. The transmission controller drives the TCC solenoid and monitors that circuit's voltage or current; an open coil, a short to ground, a short to power, or resistance well outside specification will set P0743. It is a wiring-and-solenoid code rather than a "the clutch is worn out" code — though the only way to be sure of that is to test the circuit rather than assume it.
The symptoms, causes, and diagnostic steps below describe P0743 itself, so they read the same on nearby Kia Forte model years. Powertrain and trim details vary year to year — confirm the specifics against your own vehicle before buying parts.
Is it safe to drive a 2022 Kia Forte with P0743?
In most cases a 2022 Kia Forte stays drivable for short trips with P0743 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0743 on a 2022 Kia Forte?
- Check Engine Light is illuminated
- Engine RPM at highway cruise higher than normal for the same speed
- Noticeable fuel economy drop on the highway
- No sensation of lockup engaging at cruising speed
- Transmission fluid running hot, particularly when towing
- Often paired with P0700 from the transmission controller
What causes P0743 on a 2022 Kia Forte?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed TCC solenoid (open or shorted coil) | Most common | $300–$900 |
| Transmission fluid wicked up the harness into the external connector Reads identically to a failed solenoid on a multimeter — inspect the connector before ordering parts. | Most common | $100–$500 |
| Chafed, broken, or corroded TCC solenoid wiring | Common | $80–$350 |
| Low or contaminated transmission fluid | Occasional | $100–$400 |
| Failed TCM or PCM driver for the TCC solenoid circuit | Rare | $500–$1,500 |
Cost ranges are editorial estimates for parts and labor at an independent U.S. shop — not quotes. What you actually pay moves with your region, the shop's hourly rate, which engine you have, and how much diagnostic time the job takes. Dealer service departments typically sit above these ranges.
How to diagnose this on a 2022 Kia Forte
-
Check transmission fluid level and condition first
Even on an electrical code, fluid comes first — it is cheap to check and it changes how you interpret everything else. Follow the vehicle's specific procedure, which on many modern transmissions means checking at a defined fluid temperature with the engine running. Burnt-smelling fluid or clutch material in it means the problem is bigger than a solenoid circuit.
Tools: Vehicle-specific service procedure, Replacement fluid (if needed)
-
Inspect the external transmission connector for fluid intrusion
This is the check that most often changes the outcome. A failing case seal lets fluid travel up inside the harness and pool in the connector, producing resistance readings that look exactly like a dead solenoid. Unplug the connector and look for fluid inside the body or wicking along the wires. If it is there, the seal and the contaminated harness section are the repair.
Tools: Connector unlock tool, Flashlight, Clean rags
-
Measure TCC solenoid resistance at the connector
Identify the TCC solenoid pins in the wiring diagram and measure resistance across them. Compare against the figure specified for this transmission rather than a generic range. Infinite resistance indicates an open coil or an open circuit; near zero indicates a shorted coil.
Tools: Multimeter, Wiring diagram
-
Confirm the controller is actually commanding the circuit
Back-probe the TCC control wire and drive the vehicle to a steady cruise where lockup should occur. The controller should switch the circuit. If it never commands, the problem is upstream — an input the controller needs, an enable condition not being met, or the driver inside the module — not the solenoid.
Tools: Multimeter or scope, Back-probe pins, Scan tool with TCC PIDs
-
Check the circuit wiring end to end
With the solenoid disconnected at the transmission and the controller connector accessible, check the control wire for continuity, for shorts to ground, and for shorts to power. A wire that reads voltage while disconnected at both ends is touching something it should not, and that chafe point is the repair.
Tools: Multimeter, Wiring diagram
NHTSA complaints & recalls for the 2022 Kia Forte
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Kia Forte. Use these to gauge how common a problem is on your specific vehicle before you start chasing Kia Forte diagnostics.
- ENGINE 4
- UNKNOWN OR OTHER 5
- FORWARD COLLISION AVOIDANCE 4
- STEERING 3
- SUSPENSION 3
1 active recall
- STEERING:COLUMN May 2022
Kia Motors America (Kia) is recalling certain 2021-2022 Rio and Forte vehicles. A bolt in the steering column may not be secured properly, which can cause the steering column to detach from the steering rack and result in a loss of steering control.…
NHTSA campaign 22V304000
How do I fix P0743 on a 2022 Kia Forte?
- Replace the TCC solenoid (often supplied as part of a solenoid pack)
- Repair the fluid-contaminated external connector and harness section
- Repair the failed transmission case seal that allowed fluid intrusion
- Repair chafed or shorted TCC control wiring
- Service transmission fluid and filter to the correct specification
Engines in the 2022 Kia Forte
The 2022 Kia Forte was offered with the 1.6L 4-cylinder and 2.0L 4-cylinder engines. Which one you have changes where P0743 is most likely to originate, so confirm your engine before ordering parts.
Engine data: EPA fueleconomy.gov.
What “electrical” narrows down for you
P0743 is more useful than P0740 because it tells you where to start. The controller is not reporting that lockup failed to happen — it is reporting that the circuit itself measured wrong. That means the first tools out of the box are a multimeter and a wiring diagram, not a scan tool on a test drive.
It also means the expensive outcomes are less likely. A worn torque converter clutch causes a performance code, not an electrical one. It is still possible to have both problems at once, but P0743 alone points at a solenoid, a wire, or a connector.
The connector is the check people skip
Transmission fluid climbing up inside a wiring harness is more common than most people expect, and it produces a diagnosis trap: the multimeter shows an out-of-spec solenoid circuit, the solenoid gets replaced, and the code returns within days because the actual fault was fluid bridging the connector pins.
Unplug the external connector and look inside before you order anything. If it is wet, the repair is the case seal and the contaminated harness — and the solenoid you were about to buy is probably fine.
Solenoid packs versus single solenoids
Most modern transmissions group their solenoids into a single pack that bolts to the valve body. Replacing the whole pack is frequently the same labour as replacing one solenoid inside it, because the labour is almost entirely getting to the pack. On a high-mileage transmission where the solenoids have aged together, the pack is usually the better value even though the part costs more.
How urgent is this?
The vehicle drives. What you lose is lockup, which means higher cruise RPM, worse fuel economy, and — the part that actually matters — more heat in the transmission fluid. Heat is what kills automatic transmissions. A few weeks of normal commuting is not going to destroy anything. Towing a trailer across a mountain pass with no lockup is a genuinely bad idea. If you tow, treat this as a fix-before-the-trip item.
P0743 on a 2022 Kia Forte: frequently asked questions
What does diagnostic trouble code P0743 mean on a 2022 Kia Forte?
P0743 narrows the torque converter clutch fault to the electrical circuit specifically. The transmission controller drives the TCC solenoid and monitors that circuit's voltage or current; an open coil, a short to ground, a short to power, or resistance well outside specification will set P0743. It is a wiring-and-solenoid code rather than a "the clutch is worn out" code — though the only way to be sure of that is to test the circuit rather than assume it.
What are the symptoms of P0743 on a 2022 Kia Forte?
Check Engine Light is illuminated. Engine RPM at highway cruise higher than normal for the same speed. Noticeable fuel economy drop on the highway. No sensation of lockup engaging at cruising speed. Transmission fluid running hot, particularly when towing. Often paired with P0700 from the transmission controller
What causes P0743 on a 2022 Kia Forte?
Failed TCC solenoid (open or shorted coil) (most-common). Transmission fluid wicked up the harness into the external connector (most-common). Chafed, broken, or corroded TCC solenoid wiring (common). Low or contaminated transmission fluid (occasional). Failed TCM or PCM driver for the TCC solenoid circuit (rare)
Is it safe to drive a 2022 Kia Forte with P0743?
In most cases a 2022 Kia Forte stays drivable for short trips with P0743 active, but it should be diagnosed and repaired promptly — this is a high-severity code. Ignoring it can lead to further damage or a failed emissions test.