P0740 on a 2012 Toyota Camry

Torque Converter Clutch Circuit Fault

P0740 on a 2012 Toyota Camry means torque converter clutch circuit fault. P0740 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis. Use the symptoms and test results to narrow down the cause before replacing parts.

Severity: high Check warning lights Mid-size Sedan

Maintained by MECH AI Editorial · Technical content updated

What does P0740 mean on a 2012 Toyota Camry?

P0740 is the general torque converter clutch (TCC) circuit code. Depending on the manufacturer it is set for an electrical fault in the TCC solenoid circuit — an open or a short — or for the clutch simply never engaging when the transmission controller commands it. The torque converter clutch is what mechanically locks the engine to the transmission at cruise, removing the slip that a fluid coupling always has. When it does not work, the engine turns faster than it should for a given road speed, fuel economy drops, and the transmission runs hotter than it was designed to.

The symptoms, causes, and diagnostic steps below describe P0740 itself, so they read the same on nearby Toyota Camry model years. Powertrain and trim details vary year to year — confirm the specifics against your own vehicle before buying parts.

Is it safe to drive a 2012 Toyota Camry with P0740?

P0740 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.

What are the symptoms of P0740 on a 2012 Toyota Camry?

What causes P0740 on a 2012 Toyota Camry?

Possible causes of P0740 depend on the equipment fitted. Confirm which parts and tests apply on a 2012 Toyota Camry before pricing a repair.

Cause Estimated repair (USD)
Failed TCC solenoid $300–$900
Damaged wiring or fluid-contaminated external transmission connector $100–$500
Low transmission fluid level or contaminated fluid $100–$400
Stuck TCC control valve in the valve body $400–$1,500
Worn or burned torque converter clutch friction material Requires torque converter replacement — a major job. $1,800–$4,500
Failed TCM or PCM driver for the TCC circuit $500–$1,500
Internal transmission damage allowing fluid bypass $2,500–$6,500

These are editorial estimates in U.S. dollars. A shop can price a confirmed repair using the engine, parts and local labor rate.

How to diagnose this on a 2012 Toyota Camry

  1. Check transmission fluid level and condition

    This comes first every time. Many modern transmissions have no dipstick and require a specific procedure — fluid at a defined temperature, engine running, vehicle level — to check the level at all. Follow the procedure for this vehicle. Fluid that smells burnt or carries clutch material tells you the problem is internal and no solenoid will fix it.

    Tools: Vehicle-specific service procedure, Replacement fluid (if needed)

  2. Pull all transmission codes, not just the engine codes

    P0740 on its own is one repair scope. P0740 alongside gear-ratio codes or a pressure code means broader problems that a solenoid replacement will not resolve. Read the TCM directly rather than relying on a generic scan of engine codes only.

    Tools: Scan tool with TCM access

  3. Watch TCC command against actual lockup on the road

    At a steady highway cruise, graph commanded TCC state alongside engine RPM and vehicle speed. On a healthy system the RPM drops noticeably at the moment lockup engages. Command with no RPM drop confirms the clutch is not engaging mechanically — which is the condition, not yet the cause.

    Tools: Scan tool with TCC and live RPM PIDs

  4. Test the TCC solenoid circuit electrically

    Locate the TCC solenoid pin at the external transmission connector using the wiring diagram, and measure resistance. Compare against the specification for this transmission. Infinite resistance means an open coil or an open circuit; a near-zero reading means a shorted solenoid.

    Tools: Multimeter, Wiring diagram

  5. Inspect the external transmission connector for fluid

    A failed case seal lets transmission fluid wick up inside the wiring harness and into the connector. The result mimics a failed solenoid on a multimeter while the solenoid is perfectly fine. If you find fluid in the connector, the repair is the seal and often a section of harness.

    Tools: Connector unlock tool, Flashlight

NHTSA complaints & recalls for the 2012 Toyota Camry

Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Toyota Camry. Use these to gauge how common a problem is on your specific vehicle before you start chasing Toyota Camry diagnostics.

NHTSA snapshot taken October 21, 2026; refreshed quarterly. For live figures see NHTSA.gov .

645 owner complaints
95 involved a crash
6 involved a fire
80 reported injuries
  • POWER TRAIN 146
  • VEHICLE SPEED CONTROL 73
  • UNKNOWN OR OTHER 88
  • AIR BAGS 83
  • ELECTRICAL SYSTEM 68

2 active recalls

  • ELECTRICAL SYSTEM Oct 2013

    Toyota is recalling certain model year 2012-2013 Avalon, Avalon HV, Venza, Camry, and Camry HV vehicles. In the affected vehicles, the drain hose for the air conditioning condenser may become clogged causing water to accumulate at the bottom of the air conditioning condenser unit…

    NHTSA campaign 13V442000
  • AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE Jan 2013

    Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model ye…

    NHTSA campaign 13V014000

How do I fix P0740 on a 2012 Toyota Camry?

Engines in the 2012 Toyota Camry

The 2012 Toyota Camry was offered with the 2.5L 4-cylinder and 3.5L 6-cylinder engines, including a hybrid version. Which one you have changes where P0740 is most likely to originate, so confirm your engine before ordering parts.

Engine data: EPA fueleconomy.gov.

P0740 repair guides

P0740, P0741, P0743 — three codes, one system

The torque converter clutch codes describe different aspects of the same failure, and manufacturers are not perfectly consistent about which one they set:

Code What it describes
P0740 General TCC circuit fault — electrical or “never engages”
P0741 TCC performance, or stuck off — commanded but slipping
P0742 TCC stuck on — will not release, stalls at stops
P0743 TCC circuit electrical fault specifically
P0744 TCC circuit intermittent

Because P0740 is the broad one, the same physical fault might show up as P0740 on one vehicle and P0743 on another. Do not read too much into which number appeared; read the live data instead.

What no lockup feels like from the driver’s seat

The clearest tell is highway RPM. A vehicle that used to cruise at 2,000 RPM at 70 mph and now sits noticeably higher at the same speed is running without lockup. The engine is spinning the converter’s fluid rather than being bolted to the transmission through the clutch.

The second tell is that the familiar sensation of a final “shift” at around 45–55 mph is gone. That was never a gear change — it is the lockup clutch engaging. Its absence is P0740’s signature symptom.

The third is fuel economy. Converter slip at highway speed costs real miles per gallon, which is why this code often shows up as “my mileage suddenly got worse” before anyone notices the light.

Fluid first, always

Low or degraded fluid causes hydraulic problems that look exactly like electrical ones, and it is the cheapest thing on the list to correct. Check it before touching a solenoid.

One old piece of advice deserves updating: for decades the rule was never to change the fluid in a transmission that is already misbehaving, on the theory that fresh fluid washes out accumulated material and finishes the job. With modern fluids, a drain-and-fill using the correct OEM specification is generally safe and sometimes resolves the code outright. A high-pressure machine flush on a transmission that is already slipping is still a risk worth avoiding.

When to hand this to a transmission shop

Fluid level, connector inspection, and a resistance check at the external connector are all reasonable driveway jobs. Once the diagnosis points inside — a stuck valve in the valve body, or clutch material on the pan magnet — you are into a job that needs a lift, a fluid handling setup, and transmission-specific experience. That is a good moment to stop and get a quote rather than to keep going.

P0740 on a 2012 Toyota Camry: frequently asked questions

What does diagnostic trouble code P0740 mean on a 2012 Toyota Camry?

P0740 is the general torque converter clutch (TCC) circuit code. Depending on the manufacturer it is set for an electrical fault in the TCC solenoid circuit — an open or a short — or for the clutch simply never engaging when the transmission controller commands it. The torque converter clutch is what mechanically locks the engine to the transmission at cruise, removing the slip that a fluid coupling always has. When it does not work, the engine turns faster than it should for a given road speed, fuel economy drops, and the transmission runs hotter than it was designed to.

What are the symptoms of P0740 on a 2012 Toyota Camry?

Check Engine Light is illuminated. Engine RPM at highway cruise is higher than normal for the same speed. Noticeable fuel economy drop, worst on the highway. No sensation of the transmission "shifting" into lockup at cruise. Transmission fluid running hot, especially when towing. Often paired with P0700 from the transmission controller

What causes P0740 on a 2012 Toyota Camry?

Failed TCC solenoid (estimated U.S. repair cost $300–$900). Damaged wiring or fluid-contaminated external transmission connector (estimated U.S. repair cost $100–$500). Low transmission fluid level or contaminated fluid (estimated U.S. repair cost $100–$400). Stuck TCC control valve in the valve body. Worn or burned torque converter clutch friction material. Failed TCM or PCM driver for the TCC circuit. Internal transmission damage allowing fluid bypass

Is it safe to drive a 2012 Toyota Camry with P0740?

P0740 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.

Related diagnostic codes

P0740 on other Toyota Camry model years