P0442 on a 2017 Hyundai Tucson
EVAP Small Leak Detected
P0442 on a 2017 Hyundai Tucson indicates evap small leak detected. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is loose, worn, or cross-threaded fuel cap (typically $15–$60). Confirm the root cause before replacing parts.
What does P0442 mean on a 2017 Hyundai Tucson?
P0442 is set when the EVAP system's small-leak monitor detects an opening approximately 0.040 inches (1.0 mm) or larger. This is the equivalent of the gas cap being left slightly loose or a small crack in a vent hose. The vehicle remains fully drivable and consumes no extra fuel, but the EVAP system can no longer hold the sealed vacuum required for compliance.
This guide covers P0442 across the 2015-2019 Hyundai Tucson generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Hyundai Tucson with P0442?
In most cases a 2017 Hyundai Tucson stays drivable for short trips with P0442 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0442 on a 2017 Hyundai Tucson?
- Check Engine Light is illuminated
- Faint fuel smell, especially after refueling on a hot day
- No noticeable change in drivability or fuel economy
- Vehicle will fail emissions / smog testing
What causes P0442 on a 2017 Hyundai Tucson?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Loose, worn, or cross-threaded fuel cap | Most common | $15–$60 |
| Aged or split EVAP hose | Common | $30–$200 |
| Failing purge or vent valve seal | Common | $80–$350 |
| Cracked EVAP charcoal canister | Occasional | $200–$600 |
| Damaged O-rings at hose-to-canister or hose-to-solenoid connections | Occasional | $20–$120 |
| Pinhole or seam leak in the fuel filler neck | Occasional | $150–$600 |
| Failed fuel tank vent at the tank top (less accessible to inspect) | Rare | $300–$900 |
How to diagnose this on a 2017 Hyundai Tucson
-
Tighten or replace the fuel cap
Remove and reinstall the fuel cap to at least three clicks. Inspect the rubber gasket for cracks, debris, or compression set. Replace with an OEM-spec cap if the gasket is damaged or the cap is more than 8 years old.
Tools: None
-
Smoke-test the EVAP system
A 0.040-inch leak is too small to find by ear and almost always too small to see visually without smoke. Pressurize the EVAP system with smoke at the service port and trace the smoke trail to its source. Common leak points: behind the rear bumper near the canister, the hose between purge valve and intake, and the top of the fuel tank.
Tools: EVAP smoke machine, UV dye (optional), Inspection mirror and flashlight
-
Inspect the EVAP service port itself
The green EVAP service port cap is a frequent leak point because its O-ring hardens and fails after years of heat cycles. With smoke already in the system, watch the service port specifically.
Tools: Inspection mirror
-
Visually inspect the charcoal canister
Many trucks and SUVs mount the canister behind the rear axle where it is exposed to road debris and salt spray. Cracks in the plastic housing are common on aging vehicles. Replace the canister if cracked or saturated.
Tools: Floor jack and stands, Trim panel tools
-
Verify monitor completion before re-testing
After repair, drive 2–4 cold-start drive cycles with the tank between 25 % and 75 % full. Use a scan tool to confirm the EVAP readiness flag turns "ready." Clearing the code prematurely will set the light again as soon as the monitor runs.
Tools: Scan tool with readiness monitor display
NHTSA complaints & recalls for the 2017 Hyundai Tucson
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Hyundai Tucson. Use these to gauge how common a problem is on your specific vehicle before you start chasing Hyundai Tucson diagnostics.
- ENGINE 580
- POWER TRAIN 287
- VEHICLE SPEED CONTROL 86
- UNKNOWN OR OTHER 134
- ELECTRICAL SYSTEM 83
3 active recalls
- ELECTRICAL SYSTEM:WIRING Nov 2016
Hyundai Motor America (Hyundai) is recalling certain model year 2016-2017 Tucson vehicles manufactured May 19, 2015, to November 14, 2016, and 2017 Santa Fe vehicles manufactured November 28, 2015, to November 14, 2016. The affected vehicles may be equipped with an accessory tra…
NHTSA campaign 16V842000 - ENGINE Sep 2021
Hyundai Motor America (Hyundai) is recalling certain 2017 Tucson and Sonata Hybrid vehicles. The connecting rod bearings inside the engine may wear prematurely, which can result in engine damage.…
NHTSA campaign 21V727000 - SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE Sep 2020
Hyundai Motor America (Hyundai) recalled certain 2019-2021 Tucson vehicles on September 4, 2020. On December 30, 2020, Hyundai expanded the recall population, and added certain 2016-2018 Tucson vehicles. The Anti-lock Brake Hydraulic Electronic Control Unit (HECU) could corrode…
NHTSA campaign 20V543000
How do I fix P0442 on a 2017 Hyundai Tucson?
- Replace the fuel cap
- Replace cracked EVAP hoses and aged O-rings
- Replace the EVAP purge valve or vent valve
- Replace the charcoal canister assembly
- Replace the fuel filler neck (rust or pinhole)
About the 2015-2019 Hyundai Tucson
The 2015-2019 Hyundai Tucson was commonly sold with the following powertrains: 2.5L I4, 1.6L Turbo I4, 1.6L Hybrid I4, 1.6L Plug-in Hybrid I4. Common trims include SE, SEL, XRT, N Line, Limited.
P0442 vs P0455 vs P0456
The three EVAP leak codes describe the same kind of fault at different leak sizes:
| Code | Leak size threshold | Typical real-world cause |
|---|---|---|
| P0456 | ~0.020” (very small) | Cap O-ring, fresh hose pinhole |
| P0442 | ~0.040” (small) | Loose cap, aging hose, cracked vent valve seal |
| P0455 | ~0.090”+ (large or no seal) | Missing cap, disconnected hose, large canister crack |
A vehicle that sets P0456 today often sets P0442 in a few months as the same crack grows.
Why smoke testing is non-negotiable
EVAP leaks are usually too small to find any other way. A bare-eye inspection of every hose and joint will miss most P0442 causes. The smoke machine is a one-time tool purchase (or one-time shop diagnostic fee) that pays for itself on the first EVAP repair.
What “0.040 inch leak” actually means
OBD-II EVAP monitors do not measure the leak directly. They apply a calibrated vacuum or pressure to the sealed system and time how quickly it bleeds off. The leak-equivalent diameter is calculated from that decay rate. A real-world 0.040” hole and a 0.030” hole with a smaller restriction upstream can produce the same monitor result.