P0131 on a 2022 Ford Bronco
O2 Sensor Low Voltage (Bank 1 Upstream)
P0131 on a 2022 Ford Bronco indicates o2 sensor low voltage (bank 1 upstream). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is vacuum leak causing genuine lean condition on bank 1 (typically $80–$600). Confirm the root cause before replacing parts.
What does P0131 mean on a 2022 Ford Bronco?
P0131 is set when the ECM sees the upstream oxygen sensor on Bank 1 reporting a voltage below the calibrated minimum (typically below 0.1 V) for an extended period. The sensor is either telling the ECM that the exhaust is extremely lean — and continuing to report that even when the engine is supposedly running stoichiometric — or it has failed and is stuck at a low voltage.
This guide covers P0131 across the 2020-2024 Ford Bronco generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Ford Bronco with P0131?
In most cases a 2022 Ford Bronco stays drivable for short trips with P0131 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0131 on a 2022 Ford Bronco?
- Check Engine Light is illuminated
- Rough idle and hesitation
- Reduced fuel economy
- Possible black smoke from exhaust (ECM adds fuel to "correct" lean reading)
- Slight loss of power under acceleration
- May be accompanied by P0171 (system too lean Bank 1)
What causes P0131 on a 2022 Ford Bronco?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Vacuum leak causing genuine lean condition on Bank 1 | Most common | $80–$600 |
| Exhaust leak upstream of the Bank 1 upstream O2 sensor | Common | $100–$500 |
| Failed Bank 1 upstream O2 sensor (stuck low) | Common | $150–$450 |
| Shorted-to-ground O2 sensor signal wire | Common | $80–$350 |
| Low fuel pressure causing lean mixture | Occasional | $80–$900 |
| Clogged or under-flowing Bank 1 fuel injectors | Occasional | $150–$1,000 |
| Corroded O2 sensor connector | Occasional | $30–$200 |
How to diagnose this on a 2022 Ford Bronco
-
Determine whether the lean condition is real or sensor-reported
Read fuel trims at idle and 2500 RPM. If Bank 1 long-term fuel trim (LTFT) is near zero, the engine is running fine and the O2 sensor is reporting a false lean — the sensor or its wiring is the problem. If LTFT is +15 % or higher, the engine is genuinely lean and the sensor is correctly reporting it.
Tools: Scan tool with live fuel trim PIDs
-
Check the O2 sensor signal wire continuity
Disconnect the Bank 1 upstream O2 sensor. With the connector unplugged, the scan tool PID should read a bias voltage (often 0.4–0.5 V) rather than 0 V. If it stays pinned at 0 V, the signal wire is shorted to ground somewhere between the sensor and the PCM.
Tools: Scan tool, Multimeter
-
Inspect for vacuum and exhaust leaks
Smoke-test the intake to find vacuum leaks that would cause a real Bank 1 lean condition. Then inspect the exhaust between the engine and the upstream O2 sensor — pinhole leaks pull in fresh air and bias the sensor reading low.
Tools: Smoke machine, Mechanic's stethoscope, Flashlight
-
Bench-test the O2 sensor heater circuit
An O2 sensor that does not heat up will produce low voltage because the zirconium element only generates signal when hot (350 °C+). Measure the heater resistance — typically 3–15 Ω depending on the sensor. An open heater requires sensor replacement.
Tools: Multimeter
-
Verify fuel pressure
Low fuel pressure causes a genuine lean mixture and will set P0131 along with P0171. Connect a fuel pressure gauge and observe at idle, snap-throttle, and steady cruise. Pressure below the OEM spec or dropping under load points at the pump or pressure regulator.
Tools: Fuel pressure gauge
NHTSA complaints & recalls for the 2022 Ford Bronco
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Ford Bronco. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ford Bronco diagnostics.
- ENGINE 42
- POWER TRAIN 34
- VISIBILITY/WIPER 64
- SERVICE BRAKES 41
- UNKNOWN OR OTHER 37
21 active recalls
- LATCHES/LOCKS/LINKAGES:DOORS:LOCK Jun 2022
Ford Motor Company (Ford) is recalling certain four-door 2021-2022 Bronco vehicles. The passenger-side rear door may be opened from inside of the vehicle when the child safety lock is in the "ON" position.…
NHTSA campaign 22V411000 - VISIBILITY:WINDSHIELD Jun 2022
Ford Motor Company (Ford) is recalling certain 2022 Bronco and Ranger vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle…
NHTSA campaign 22V451000 - BACK OVER PREVENTION: SENSING SYSTEM: CAMERA Nov 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requireme…
NHTSA campaign 22V825000 - AIR BAGS:SENSOR:SIDE IMPACT Dec 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The right or left side impact sensors may not be properly secured to the vehicle.…
NHTSA campaign 22V928000
How do I fix P0131 on a 2022 Ford Bronco?
- Repair vacuum leak(s) on Bank 1 intake
- Repair exhaust leak(s) upstream of the front O2 sensor
- Replace the Bank 1 upstream O2 sensor with an OEM part
- Repair shorted-to-ground O2 signal wire
- Service fuel system if low pressure is confirmed
About the 2020-2024 Ford Bronco
The 2020-2024 Ford Bronco was commonly sold with the following powertrains: 2.3L EcoBoost I4, 2.7L EcoBoost V6. Common trims include Base, Big Bend, Black Diamond, Outer Banks, Badlands, Wildtrak, Raptor.
How to tell a sensor problem from a real lean condition
P0131 by itself, with normal fuel trims, is almost always a sensor or wiring problem. P0131 paired with P0171 (system too lean Bank 1) is almost always a real lean condition that the sensor is correctly reporting. The fuel trim reading is the deciding piece of data.
O2 sensor replacement: OEM vs aftermarket
Wide-band oxygen sensors used in modern emissions systems are calibrated devices. Generic aftermarket sensors sold at half the OEM price often have different response curves, which causes the ECM’s fuel trim algorithm to misbehave even though the sensor “works.” Buy NTK, Denso, or Bosch OEM-equivalent — and confirm the part is listed for your specific year, make, model, engine, and emissions package (federal vs. California).
Lean caused by ethanol mixed fuel
A handful of P0131 cases on rural-use vehicles trace back to higher ethanol content in the fuel (E20+ instead of E10). The wide-band sensor is fine; the fuel is leaner than the ECM expects. If P0131 appeared right after a fill-up at an unfamiliar station, try a tank of premium-grade gasoline from a major-brand station and recheck.