P0136 on a 2022 Ford Bronco
Post-Cat O2 Sensor Circuit Fault (Bank 1)
P0136 on a 2022 Ford Bronco indicates post-cat o2 sensor circuit fault (bank 1). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed bank 1 downstream o2 sensor (typically $150–$450). Confirm the root cause before replacing parts.
What does P0136 mean on a 2022 Ford Bronco?
P0136 is set when the ECM detects a general circuit fault on the Bank 1 downstream (post-catalyst) oxygen sensor. Unlike the more specific P0137 (low voltage), P0138 (high voltage), or P0140 (no activity), P0136 is the generic circuit code that covers wiring issues, intermittent connection problems, or signals that go outside expected ranges in a way that doesn't fit a more specific fault category.
This guide covers P0136 across the 2020-2024 Ford Bronco generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Ford Bronco with P0136?
In most cases a 2022 Ford Bronco stays drivable for short trips with P0136 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0136 on a 2022 Ford Bronco?
- Check Engine Light is illuminated
- Catalyst readiness monitor will not complete
- Possible slight reduction in fuel economy
- Often no drivability symptoms
- Vehicle will fail emissions / smog testing
What causes P0136 on a 2022 Ford Bronco?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed Bank 1 downstream O2 sensor | Most common | $150–$450 |
| Damaged sensor wiring (chafed against exhaust) | Common | $80–$350 |
| Corroded O2 sensor connector | Common | $30–$200 |
| Exhaust leak upstream of the downstream sensor | Occasional | $100–$500 |
| Damaged or compressed sensor pigtail from a previous repair | Occasional | $80–$300 |
| Failed PCM input (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2022 Ford Bronco
-
Read all O2-related codes to refine the picture
P0136 alone is generic. With P0137 it points at low voltage specifically; with P0138 at high voltage; with P0140 at no activity at all; with P0141 at the heater. Cross-referencing tells you whether the diagnostic should target wiring, sensor element, or heater.
Tools: Scan tool with full code retrieval
-
Inspect the sensor wiring
Trace the downstream sensor's harness from the sensor body back to the chassis connector. Look for melted insulation (from exhaust contact), chafing against suspension components, or rodent damage. Repair before replacing the sensor.
Tools: Flashlight, Inspection mirror, Wire repair supplies
-
Test the sensor connector
Disconnect and inspect for water intrusion, corrosion, bent pins. Clean with electrical contact cleaner. The downstream connector sits under the vehicle and gets road spray; corrosion is common after a few salt-belt winters.
Tools: Electrical contact cleaner, Magnifying glass
-
Graph the sensor signal
With engine warm and held at 2500 RPM, watch the Bank 1 downstream O2 voltage. A healthy sensor sits relatively steady around 0.6–0.8 V. Rapid switching, signal stuck at one value, or no signal at all confirms a sensor or wiring issue.
Tools: Scan tool with graphing PIDs
-
Verify the bias voltage from the PCM
Disconnect the sensor and key on. The scan tool should still show bias voltage (typically 0.4–0.5 V) at the connector. If not present, the issue is between the connector and the PCM, not the sensor.
Tools: Scan tool, Multimeter
NHTSA complaints & recalls for the 2022 Ford Bronco
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Ford Bronco. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ford Bronco diagnostics.
- ENGINE 42
- POWER TRAIN 34
- VISIBILITY/WIPER 64
- SERVICE BRAKES 41
- UNKNOWN OR OTHER 37
21 active recalls
- LATCHES/LOCKS/LINKAGES:DOORS:LOCK Jun 2022
Ford Motor Company (Ford) is recalling certain four-door 2021-2022 Bronco vehicles. The passenger-side rear door may be opened from inside of the vehicle when the child safety lock is in the "ON" position.…
NHTSA campaign 22V411000 - VISIBILITY:WINDSHIELD Jun 2022
Ford Motor Company (Ford) is recalling certain 2022 Bronco and Ranger vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle…
NHTSA campaign 22V451000 - BACK OVER PREVENTION: SENSING SYSTEM: CAMERA Nov 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requireme…
NHTSA campaign 22V825000 - AIR BAGS:SENSOR:SIDE IMPACT Dec 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The right or left side impact sensors may not be properly secured to the vehicle.…
NHTSA campaign 22V928000
How do I fix P0136 on a 2022 Ford Bronco?
- Replace the Bank 1 downstream O2 sensor with an OEM part
- Repair damaged downstream sensor wiring
- Clean or replace corroded sensor connector
- Repair upstream exhaust leaks
About the 2020-2024 Ford Bronco
The 2020-2024 Ford Bronco was commonly sold with the following powertrains: 2.3L EcoBoost I4, 2.7L EcoBoost V6. Common trims include Base, Big Bend, Black Diamond, Outer Banks, Badlands, Wildtrak, Raptor.
Why P0136 is the catch-all post-cat code
Each O2 sensor has a family of possible codes:
| Code | Meaning |
|---|---|
| P0136 | Generic circuit issue (catch-all) |
| P0137 | Voltage too low (open or short to ground) |
| P0138 | Voltage too high (short to power or rich condition) |
| P0140 | No activity detected (sensor isn’t reporting anything) |
| P0141 | Heater circuit fault |
When the ECM detects a problem that doesn’t fit the more specific patterns, it falls back to P0136. Reading other codes alongside narrows the diagnosis significantly — P0136 alone is much harder to pin down than P0136 + P0140.
What “downstream sensor” actually monitors
The Bank 1 downstream sensor is mounted in the exhaust after the catalytic converter on Bank 1 (the cylinder bank containing cylinder #1). Its main job is catalyst monitoring — comparing its signal to the upstream sensor’s signal to determine whether the catalyst is still scrubbing exhaust gases.
It provides a secondary, slower fuel-trim correction layer on top of upstream-sensor closed-loop control, but it is not the primary fuel feedback. A bad downstream sensor primarily affects emissions monitoring rather than drivability.
OEM vs aftermarket sensors
The downstream sensor’s role is comparison, not raw measurement, so it is slightly less picky about sensor response curve than the upstream. But aftermarket sensors still produce inconsistent results; for $30 more, an OEM Bosch, Denso, or NTK sensor is worth it on a vehicle you plan to keep.