P0118 on a 2022 Honda Pilot
Coolant Temp Sensor High Input
P0118 on a 2022 Honda Pilot indicates coolant temp sensor high input. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is disconnected or unlatched ect sensor connector (typically $0–$50). Confirm the root cause before replacing parts.
What does P0118 mean on a 2022 Honda Pilot?
P0118 is set when the engine control module reads the engine coolant temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold coolant temperature (often −40 °F / −40 °C). This is the open-circuit fingerprint for the ECT sensor: a disconnected sensor, a broken signal wire, or a sensor failed open internally.
This guide covers P0118 across the 2020-2024 Honda Pilot generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Honda Pilot with P0118?
In most cases a 2022 Honda Pilot stays drivable for short trips with P0118 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0118 on a 2022 Honda Pilot?
- Check Engine Light is illuminated
- Temperature gauge reads zero or stays cold
- Difficult cold start with rich-running symptoms
- Cooling fans may run constantly (ECM thinks coolant is dangerously cold)
- Slightly reduced fuel economy
- Cold-running engine doesn't warm up properly per the gauge
- Possible hard start when the engine is hot (ECM commands cold-start enrichment)
What causes P0118 on a 2022 Honda Pilot?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Disconnected or unlatched ECT sensor connector | Most common | $0–$50 |
| Broken or chafed ECT signal wire (open circuit) | Common | $80–$350 |
| Internally failed ECT sensor (element opened) | Common | $30–$200 |
| Corroded sensor connector pins | Common | $30–$200 |
| Damaged sensor body from coolant leak or freeze | Occasional | $50–$250 |
| Failed PCM signal input (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2022 Honda Pilot
-
Read ECT temperature with a scan tool
A working ECT reads close to ambient air temperature when the engine has been off long enough to cool. A reading of "−40 °F" or "−40 °C" is the classic open-circuit fingerprint.
Tools: Scan tool with ECT PID
-
Inspect the connector and visible wiring
Locate the ECT sensor (usually threaded into the intake manifold or thermostat housing). Unplug, inspect for corrosion, water, bent pins. Re-seat and clear the code — if it stays clear, the connector was the problem.
Tools: Electrical contact cleaner, Flashlight
-
Bench-test the ECT sensor resistance
Remove the sensor (place a rag — coolant will drip). Measure resistance across its terminals at room temperature. Compare to the service manual — most NTC ECTs read 2.0–4.5 kΩ at 68 °F (20 °C). Infinite resistance means the sensor is open and needs replacement.
Tools: Multimeter, Service spec sheet, Coolant catch and replacement
-
Verify signal-wire continuity to the PCM
With the ECT disconnected, check continuity from the sensor's signal wire to the corresponding PCM pin. Open circuit confirms a broken wire somewhere along the path. Visual inspection of the harness — particularly where it routes near hot exhaust or moving accessories — often reveals the chafe point.
Tools: Multimeter, Wiring diagram
-
Jumper-test the signal wire
With the ECT disconnected, briefly jumper the signal wire to ground and observe the scan tool — the reading should swing from "very cold" to "very hot." No swing points at the wiring or PCM input rather than the sensor.
Tools: Jumper wire, Scan tool
NHTSA complaints & recalls for the 2022 Honda Pilot
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Honda Pilot. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda Pilot diagnostics.
- ENGINE 21
- POWER TRAIN 12
- FORWARD COLLISION AVOIDANCE 33
- UNKNOWN OR OTHER 27
- ELECTRICAL SYSTEM 26
4 active recalls
- BACK OVER PREVENTION:DISPLAY FUNCTION Jun 2023
Honda (American Honda Motor Co.) is recalling certain 2018-2023 Odyssey, 2019-2022 Pilot, and 2019-2023 Passport vehicles. Due to a faulty Media Oriented Systems Transport (MOST) communication coaxial cable connector, the rearview camera image may not appear on the display. As…
NHTSA campaign 23V431000 - SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER Jun 2023
Honda (American Honda Motor Co.) is recalling certain 2020-2021 Civic, 2020-2023 Ridgeline, 2021-2023 Passport, 2021-2022 Pilot, and 2020 Acura MDX vehicles. The tie rod fastener that connects the brake booster and the brake master cylinder may have been improperly assembled dur…
NHTSA campaign 23V458000 - AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION:FRONT PASSENGER Feb 2024
Honda (American Honda Motor Co.) is recalling certain 2020-2022 Pilot, Accord, Civic sedan, HR-V, Odyssey, 2020 Civic coupe, Fit, 2021-2022 Civic hatchback, 2021 Civic Type R, Insight, 2020-2021 CR-V, CR-V Hybrid, Passport, Ridgeline, Accord Hybrid, 2020 Acura MDX, 2022 Acura MDX…
NHTSA campaign 24V064000 - AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION:FRONT PASSENGER May 2026
Honda (American Honda Motor Co.) is recalling certain 2018-2021, 2023 Acura TLX, 2019-2024 RDX, 2017-2020, 2022-2026 MDX, 2017-2021, 2023, 2025 Honda Ridgeline, 2017-2022 Pilot, 2019-2021 Passport, 2018-2026 Odyssey, 2019-2022 Insight, 2019-2021 HR-V, 2018-2020 Fit, 2020-2022 CR-…
NHTSA campaign 26V332000
How do I fix P0118 on a 2022 Honda Pilot?
- Reconnect the ECT sensor connector
- Replace the ECT sensor with an OEM part
- Repair the broken ECT signal wire
- Clean corroded connector pins
About the 2020-2024 Honda Pilot
The 2020-2024 Honda Pilot was commonly sold with the following powertrains: 3.5L V6. Common trims include LX, EX, EX-L, Touring, Elite, TrailSport.
P0118 vs P0117
These are the two ends of the same circuit:
- P0117 — ECT signal too low (sensor reads very high temperature like “300 °F”). Usually a shorted-to-ground wire or sensor failed closed.
- P0118 — ECT signal too high (sensor reads very low temperature like “−40 °F”). Usually an open circuit — disconnected, broken wire, or sensor open internally.
Why P0118 causes a hot engine to run rich
When the ECT signal goes missing or reads “very cold,” the ECM commands cold-start enrichment continuously — even on a hot engine. The result: fouled spark plugs, rich-running symptoms, possibly a hard start when the engine is actually warm because flooding occurs. This is why P0118 is worth fixing promptly even though it doesn’t look like a serious code.
Multi-sensor confusion: ECT vs IAT vs CHT
Modern engines may have multiple temperature sensors:
- ECT (Engine Coolant Temperature) — in coolant passage
- IAT (Intake Air Temperature) — in air intake tract
- CHT (Cylinder Head Temperature) — bolted to head, no coolant contact
- TFT (Transmission Fluid Temperature) — in transmission
Their codes are similar — P0118 (ECT high), P0113 (IAT high), P0119 (ECT erratic). Make sure the connector you are pulling is for the sensor referenced in the code.