P0118 on a 2012 Honda Pilot
Coolant Temp Sensor High Input
P0118 on a 2012 Honda Pilot indicates coolant temp sensor high input. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is disconnected or unlatched ect sensor connector (typically $0–$50). Confirm the root cause before replacing parts.
What does P0118 mean on a 2012 Honda Pilot?
P0118 is set when the engine control module reads the engine coolant temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold coolant temperature (often −40 °F / −40 °C). This is the open-circuit fingerprint for the ECT sensor: a disconnected sensor, a broken signal wire, or a sensor failed open internally.
This guide covers P0118 across the 2010-2014 Honda Pilot generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Honda Pilot with P0118?
In most cases a 2012 Honda Pilot stays drivable for short trips with P0118 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0118 on a 2012 Honda Pilot?
- Check Engine Light is illuminated
- Temperature gauge reads zero or stays cold
- Difficult cold start with rich-running symptoms
- Cooling fans may run constantly (ECM thinks coolant is dangerously cold)
- Slightly reduced fuel economy
- Cold-running engine doesn't warm up properly per the gauge
- Possible hard start when the engine is hot (ECM commands cold-start enrichment)
What causes P0118 on a 2012 Honda Pilot?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Disconnected or unlatched ECT sensor connector | Most common | $0–$50 |
| Broken or chafed ECT signal wire (open circuit) | Common | $80–$350 |
| Internally failed ECT sensor (element opened) | Common | $30–$200 |
| Corroded sensor connector pins | Common | $30–$200 |
| Damaged sensor body from coolant leak or freeze | Occasional | $50–$250 |
| Failed PCM signal input (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2012 Honda Pilot
-
Read ECT temperature with a scan tool
A working ECT reads close to ambient air temperature when the engine has been off long enough to cool. A reading of "−40 °F" or "−40 °C" is the classic open-circuit fingerprint.
Tools: Scan tool with ECT PID
-
Inspect the connector and visible wiring
Locate the ECT sensor (usually threaded into the intake manifold or thermostat housing). Unplug, inspect for corrosion, water, bent pins. Re-seat and clear the code — if it stays clear, the connector was the problem.
Tools: Electrical contact cleaner, Flashlight
-
Bench-test the ECT sensor resistance
Remove the sensor (place a rag — coolant will drip). Measure resistance across its terminals at room temperature. Compare to the service manual — most NTC ECTs read 2.0–4.5 kΩ at 68 °F (20 °C). Infinite resistance means the sensor is open and needs replacement.
Tools: Multimeter, Service spec sheet, Coolant catch and replacement
-
Verify signal-wire continuity to the PCM
With the ECT disconnected, check continuity from the sensor's signal wire to the corresponding PCM pin. Open circuit confirms a broken wire somewhere along the path. Visual inspection of the harness — particularly where it routes near hot exhaust or moving accessories — often reveals the chafe point.
Tools: Multimeter, Wiring diagram
-
Jumper-test the signal wire
With the ECT disconnected, briefly jumper the signal wire to ground and observe the scan tool — the reading should swing from "very cold" to "very hot." No swing points at the wiring or PCM input rather than the sensor.
Tools: Jumper wire, Scan tool
NHTSA complaints & recalls for the 2012 Honda Pilot
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Honda Pilot. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda Pilot diagnostics.
- ENGINE 35
- POWER TRAIN 20
- VEHICLE SPEED CONTROL 17
- SERVICE BRAKES 28
- ELECTRICAL SYSTEM 22
9 active recalls
- AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Sep 2018
Honda (American Honda Motor Co.) is recalling certain 2014 Honda Insight and Acura TSX and TSX Wagon, 2014-2015 Honda Crosstour and Pilot vehicles nationwide, as well as certain 2014 Honda FCX Clarity and Fit EV vehicles in Florida, Hawaii, Puerto Rico, Texas, Alabama, Georgia, L…
NHTSA campaign 18V661000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Apr 2018
Honda (American Honda Motor Co.) is recalling certain 2003-2012 Honda Accord and Pilot, 2010 Accord Crosstour, 2001-2011 Civic, 2002-2011 CR-V, 2003-2004, 2006-2008 and 2011 Element, 2007 and 2009-2013 Fit, 2010-2012 Insight, 2002-2004 Odyssey, and 2012 Ridgeline vehicles. The f…
NHTSA campaign 18V268000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Jun 2019
Honda (American Honda Motor Co.) is recalling certain 2009-2014 Acura TSX, 2011-2014 TSX Sport Wagon, 2010-2013 ZDX, 2008-2012 Honda Accord, 2010-2011 Accord Crosstour, 2006-2011 Civic and Civic Hybrid, 2008-2010 Civic GX NGV, 2012-2015 Crosstour, 2007-2011 CR-V, 2009-2013 Fit, 2…
NHTSA campaign 19V502000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE May 2019
Honda (American Honda Motor Co.) is recalling certain 2009-2014 Acura TSX, 2011-2013 TSX Sport Wagon, and 2010-2012 ZDX and 2008-2012 Honda Accord, 2010-2011 Accord Crosstour, 2006-2011 Civic, Civic Hybrid and Civic NGV, 2012-2014 Crosstour, 2007-2011 CR-V, 2009-2013 Fit, 2010-20…
NHTSA campaign 19V378000
How do I fix P0118 on a 2012 Honda Pilot?
- Reconnect the ECT sensor connector
- Replace the ECT sensor with an OEM part
- Repair the broken ECT signal wire
- Clean corroded connector pins
About the 2010-2014 Honda Pilot
The 2010-2014 Honda Pilot was commonly sold with the following powertrains: 3.5L V6. Common trims include LX, EX, EX-L, Touring, Elite, TrailSport.
P0118 vs P0117
These are the two ends of the same circuit:
- P0117 — ECT signal too low (sensor reads very high temperature like “300 °F”). Usually a shorted-to-ground wire or sensor failed closed.
- P0118 — ECT signal too high (sensor reads very low temperature like “−40 °F”). Usually an open circuit — disconnected, broken wire, or sensor open internally.
Why P0118 causes a hot engine to run rich
When the ECT signal goes missing or reads “very cold,” the ECM commands cold-start enrichment continuously — even on a hot engine. The result: fouled spark plugs, rich-running symptoms, possibly a hard start when the engine is actually warm because flooding occurs. This is why P0118 is worth fixing promptly even though it doesn’t look like a serious code.
Multi-sensor confusion: ECT vs IAT vs CHT
Modern engines may have multiple temperature sensors:
- ECT (Engine Coolant Temperature) — in coolant passage
- IAT (Intake Air Temperature) — in air intake tract
- CHT (Cylinder Head Temperature) — bolted to head, no coolant contact
- TFT (Transmission Fluid Temperature) — in transmission
Their codes are similar — P0118 (ECT high), P0113 (IAT high), P0119 (ECT erratic). Make sure the connector you are pulling is for the sensor referenced in the code.
P0118 on a 2012 Honda Pilot: frequently asked questions
What does diagnostic trouble code P0118 mean on a 2012 Honda Pilot?
P0118 is set when the engine control module reads the engine coolant temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold coolant temperature (often −40 °F / −40 °C). This is the open-circuit fingerprint for the ECT sensor: a disconnected sensor, a broken signal wire, or a sensor failed open internally.
What are the symptoms of P0118 on a 2012 Honda Pilot?
Check Engine Light is illuminated. Temperature gauge reads zero or stays cold. Difficult cold start with rich-running symptoms. Cooling fans may run constantly (ECM thinks coolant is dangerously cold). Slightly reduced fuel economy. Cold-running engine doesn't warm up properly per the gauge. Possible hard start when the engine is hot (ECM commands cold-start enrichment)
What causes P0118 on a 2012 Honda Pilot?
Disconnected or unlatched ECT sensor connector (most-common). Broken or chafed ECT signal wire (open circuit) (common). Internally failed ECT sensor (element opened) (common). Corroded sensor connector pins (common). Damaged sensor body from coolant leak or freeze (occasional). Failed PCM signal input (rare) (rare)
Is it safe to drive a 2012 Honda Pilot with P0118?
In most cases a 2012 Honda Pilot stays drivable for short trips with P0118 active, but it should be diagnosed and repaired promptly — this is a moderate-severity code. Ignoring it can lead to further damage or a failed emissions test.