P0014 on a 2022 Toyota Camry
Exhaust Cam Over-Advanced (Bank 1, VVT)
P0014 on a 2022 Toyota Camry indicates exhaust cam over-advanced (bank 1, vvt). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is stuck or sludged exhaust-side vvt oil control valve (typically $100–$450). Confirm the root cause before replacing parts.
What does P0014 mean on a 2022 Toyota Camry?
P0014 is set when the engine control module commands the Bank 1 exhaust camshaft to a specific advance position and the actual cam position does not match within tolerance. On engines with dual-cam VVT (intake + exhaust phasers), P0014 is the exhaust-side counterpart of P0011. The cause is almost always the same family of failures: a stuck oil control valve, dirty oil starving the phaser, or the phaser itself failing.
This guide covers P0014 across the 2020-2024 Toyota Camry generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Toyota Camry with P0014?
In most cases a 2022 Toyota Camry stays drivable for short trips with P0014 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0014 on a 2022 Toyota Camry?
- Check Engine Light is illuminated
- Rough idle, particularly when the engine is hot
- Reduced low-end torque and slow throttle response
- Increased emissions at idle
- Possible engine stalling at low RPM
- Slight reduction in fuel economy
- Cold-start rattle from the cam area
What causes P0014 on a 2022 Toyota Camry?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Stuck or sludged exhaust-side VVT oil control valve | Most common | $100–$450 |
| Low engine oil level or pressure starving the exhaust cam phaser | Most common | $50–$200 |
| Sludged oil passages from skipped maintenance | Common | $100–$600 |
| Failed exhaust cam phaser / VVT actuator | Common | $600–$1,800 |
| Stretched timing chain affecting exhaust cam position | Occasional | $800–$3,000 |
| Damaged exhaust cam sensor wiring or connector | Occasional | $80–$350 |
How to diagnose this on a 2022 Toyota Camry
-
Confirm oil level, condition, and pressure first
VVT systems are oil-powered. Verify level is at full on a level surface with a warm engine, oil is clean (not dark or sludgy), and viscosity matches the OEM spec. Measure oil pressure with a mechanical gauge — typical 15–25 psi at idle, 40–60 psi at 2500 RPM. Low pressure must be fixed before chasing VVT parts.
Tools: Mechanical oil pressure gauge, Dipstick / level check
-
Read live exhaust cam position vs. commanded position
Scan-tool live data shows commanded and actual cam position. Watch while bidirectionally commanding cam advance. A working system tracks within 1–2 degrees of command. Lag of 5 degrees or oscillation points at the actuator or oil control valve.
Tools: Bidirectional scan tool with cam position PIDs
-
Inspect and clean the exhaust-side oil control valve
Remove the exhaust-side OCV. Check the inlet screen for sludge or metal debris. Bench-test with 12 V — the valve should click and open. Air should pass freely when energized and seal when de-energized. A sticking valve causes the most common P0014.
Tools: Socket set, Brake cleaner (NOT MAF-safe), 12 V test source, Compressed air
-
Listen for cam phaser noise at startup
A failing exhaust phaser often rattles at cold start for 1–3 seconds. Use a mechanic's stethoscope at the front of the cylinder head. The noise stops as oil pressure builds. Continuous rattle indicates advanced phaser wear.
Tools: Mechanic's stethoscope
-
Verify timing chain integrity (specific engines)
On engines with documented chain wear (BMW N20/N26, Ford 5.4 3V, VW EA888, GM 3.6 LFX), the phaser cannot fully advance once the chain has stretched — P0014 sets even with a perfect phaser. Check live cam-crank correlation drift under load.
Tools: Scan tool with cam-crank correlation
Known Technical Service Bulletins for the 2020-2024 Toyota Camry
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Toyota Camry.
- ENGINE Feb 27, 2026
OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.
NHTSA #11029896 - ELECTRICAL SYSTEM Jan 30, 2026
OBSOLETE NOTICE January 30, 2026: This bulletin is now obsolete. Please see T-SB-0001-26.
NHTSA #11028726 - ELECTRICAL SYSTEM Jan 28, 2026
Some 2018 – 2024 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.
NHTSA #11028722 - UNKNOWN OR OTHER Jan 7, 2026
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA #11028712 - ENGINE Aug 7, 2025
The specific condition covered by this program is for a small engine coolant leak that can occur from the flow shut-off valve that can allow coolant to drip on other parts of the vehicle. This can cause "Engine Maintenance Required" to be displayed on the instrument cluster or cause the A/C not to function normally. Although the flow shut-off valve is covered by Toyota’s New Vehicle Limited Warranty for 36 months or 36,000 miles (whichever comes first), we at Toyota care about the customers’ ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.
NHTSA #11022949 - ELECTRICAL SYSTEM Jun 25, 2025
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
NHTSA #11020670
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
NHTSA complaints & recalls for the 2022 Toyota Camry
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Toyota Camry. Use these to gauge how common a problem is on your specific vehicle before you start chasing Toyota Camry diagnostics.
- VEHICLE SPEED CONTROL 6
- AIR BAGS 10
- UNKNOWN OR OTHER 7
- SERVICE BRAKES 7
- ELECTRICAL SYSTEM 7
1 active recall
- AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION Dec 2023
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2020-2021 Avalon, Avalon Hybrid, Corolla, Highlander, Highlander Hybrid, RAV4, RAV4 Hybrid, Lexus ES350, Lexus RX350, Lexus RX450H, 2021 Sienna Hybrid, Lexus ES250, 2020-2022 Camry, Camry Hybrid, and ES300H ve…
NHTSA campaign 23V865000
How do I fix P0014 on a 2022 Toyota Camry?
- Change engine oil and filter with the correct OEM viscosity
- Clean or replace the exhaust-side VVT oil control valve
- Replace the exhaust cam phaser / actuator assembly
- Replace stretched timing chain and components as a kit
- Repair damaged cam sensor wiring
About the 2020-2024 Toyota Camry
The 2020-2024 Toyota Camry was commonly sold with the following powertrains: 2.5L I4, 3.5L V6, 2.5L Hybrid I4. Common trims include LE, SE, XLE, XSE.
P0014 vs P0011
These two codes describe the same kind of fault on different camshafts:
- P0011 — intake cam Bank 1 timing over-advanced
- P0014 — exhaust cam Bank 1 timing over-advanced
Engines with dual VVT have separate phasers and separate oil control valves for intake and exhaust. P0011 and P0014 setting together points to a common cause (oil pressure, sludge, common chain issue). P0014 alone isolates to the exhaust-side hardware.
Why oil maintenance matters more than the phaser itself
Most P0014 cases on engines with under 100,000 miles trace back to oil maintenance: extended intervals, wrong viscosity, or a slow oil leak that drops level over time. The cam phaser is mechanically robust if fed clean, high-pressure oil. A $50 oil change has resolved more P0014 codes than any other single repair.
Engines that disproportionately set P0014
- Toyota 2GR-FE V6 — exhaust OCV failure around 100k miles
- Ford 3.5L EcoBoost V6 (Gen 1) — phaser rattle leading to P0014
- Hyundai/Kia Theta II 2.4 GDI — both P0011 and P0014 from oil sludge
- GM 3.6 LFX/LLT V6 — chain stretch progresses from P0017 to P0014
P0014 on a 2022 Toyota Camry: frequently asked questions
What does diagnostic trouble code P0014 mean on a 2022 Toyota Camry?
P0014 is set when the engine control module commands the Bank 1 exhaust camshaft to a specific advance position and the actual cam position does not match within tolerance. On engines with dual-cam VVT (intake + exhaust phasers), P0014 is the exhaust-side counterpart of P0011. The cause is almost always the same family of failures: a stuck oil control valve, dirty oil starving the phaser, or the phaser itself failing.
What are the symptoms of P0014 on a 2022 Toyota Camry?
Check Engine Light is illuminated. Rough idle, particularly when the engine is hot. Reduced low-end torque and slow throttle response. Increased emissions at idle. Possible engine stalling at low RPM. Slight reduction in fuel economy. Cold-start rattle from the cam area
What causes P0014 on a 2022 Toyota Camry?
Stuck or sludged exhaust-side VVT oil control valve (most-common). Low engine oil level or pressure starving the exhaust cam phaser (most-common). Sludged oil passages from skipped maintenance (common). Failed exhaust cam phaser / VVT actuator (common). Stretched timing chain affecting exhaust cam position (occasional). Damaged exhaust cam sensor wiring or connector (occasional)
Is it safe to drive a 2022 Toyota Camry with P0014?
In most cases a 2022 Toyota Camry stays drivable for short trips with P0014 active, but it should be diagnosed and repaired promptly — this is a high-severity code. Ignoring it can lead to further damage or a failed emissions test.