P0013 on a 2022 Toyota Camry
Exhaust Cam Actuator Circuit Fault (Bank 1)
What does P0013 mean on a 2022 Toyota Camry?
P0013 is an electrical-circuit fault on the Bank 1 exhaust camshaft position actuator (OCV / VVT solenoid). The ECM cannot detect the expected current draw when it commands the solenoid, indicating an open circuit, short, or failed driver. Unlike P0014 (over-advanced) which is a position fault, P0013 is specifically a wiring / coil fault — the ECM is reporting that it cannot even communicate with the actuator.
Symptoms on a 2022 Toyota Camry
- Check Engine Light is illuminated
- Loss of mid-range torque
- Rough idle when warm
- Hesitation or stumble on light acceleration
- Reduced fuel economy
- Possible engine stalling at low RPM
Likely causes on a 2022 Toyota Camry
- Failed exhaust OCV / VVT solenoid coil (open or shorted) Most commonEstimated repair: $100– $450
- Damaged OCV connector or chafed signal wiring CommonEstimated repair: $50– $250
- Corroded connector pins from heat / oil exposure CommonEstimated repair: $30– $200
- Shorted-to-power or shorted-to-ground OCV wire OccasionalEstimated repair: $80– $350
- Failed PCM driver for the exhaust OCV (rare) RareEstimated repair: $400– $1,500
How to diagnose this on a 2022 Toyota Camry
-
Measure OCV coil resistance
Unplug the exhaust-side OCV on Bank 1. Measure resistance across the solenoid terminals. Most OCVs read 6 to 15 Ω. Infinite resistance is an open coil; near zero is a shorted coil. Either requires solenoid replacement.
Tools: Multimeter, Service spec sheet
-
Inspect the connector
Unplug the connector and look closely for corrosion, bent pins, oil intrusion, or melted insulation. The OCV lives in a hot, oily environment and connectors degrade. Clean with electrical contact cleaner.
Tools: Electrical contact cleaner, Magnifying glass
-
Verify wiring continuity to the PCM
With the OCV disconnected and the connector unplugged at the PCM, measure continuity between each wire and its corresponding PCM pin. Open circuit indicates a broken wire. Short to ground or to power indicates chafed insulation contacting nearby metal or a power source.
Tools: Multimeter, Wiring diagram, Back-probe pins
-
Command the OCV with a scan tool
Bidirectional scan tools can command the OCV on and off while watching live current draw. A working solenoid clicks audibly when commanded. No click + a P0013 confirms either the coil or the wiring.
Tools: Bidirectional scan tool
-
Test for shorted wiring at the engine harness
With the engine off and the OCV unplugged, key on, briefly check the supply wire for unexpected voltage. A "hot" wire with the PCM not commanding the OCV indicates a short to power in the harness.
Tools: Multimeter
Known Technical Service Bulletins for the 2020-2024 Toyota Camry
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Toyota Camry.
- ENGINE Feb 26, 2026
OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.
NHTSA #11029896 - ELECTRICAL SYSTEM Jan 29, 2026
OBSOLETE NOTICE January 30, 2026: This bulletin is now obsolete. Please see T-SB-0001-26.
NHTSA #11028726 - ELECTRICAL SYSTEM Jan 27, 2026
Some 2018 – 2024 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.
NHTSA #11028722 - UNKNOWN OR OTHER Jan 6, 2026
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA #11028712 - ENGINE Aug 6, 2025
The specific condition covered by this program is for a small engine coolant leak that can occur from the flow shut-off valve that can allow coolant to drip on other parts of the vehicle. This can cause "Engine Maintenance Required" to be displayed on the instrument cluster or cause the A/C not to function normally. Although the flow shut-off valve is covered by Toyota’s New Vehicle Limited Warranty for 36 months or 36,000 miles (whichever comes first), we at Toyota care about the customers’ ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.
NHTSA #11022949 - ELECTRICAL SYSTEM Jun 24, 2025
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
NHTSA #11020670
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
Common fixes
- Replace the exhaust-side VVT oil control valve / OCV
- Repair damaged OCV connector or wiring
- Clean corroded connector pins
- Repair shorted-to-power or shorted-to-ground signal wire
About the 2020-2024 Toyota Camry
The 2020-2024 Toyota Camry was commonly sold with the following powertrains: 2.5L I4, 3.5L V6, 2.5L Hybrid I4. Common trims include LE, SE, XLE, XSE.
P0013 vs P0014
These are the two ways the exhaust VVT system fails on the same hardware:
- P0013 — electrical fault. The ECM cannot drive the solenoid because the circuit is open, shorted, or the coil is dead. No hydraulic action happens at all.
- P0014 — position fault. The solenoid IS being driven, but the cam position does not match what was commanded. The hydraulic side is the problem (sludged passages, failed phaser).
Diagnostic approach differs: P0013 is electrical (resistance, wiring, connector). P0014 is hydraulic (oil pressure, OCV mechanical function, phaser).
When P0013 is the cheap fix
Roughly 60–70 % of P0013 cases trace to the solenoid coil itself — which is a $40–$150 OEM part on most engines and a 10-minute replacement. The other 30–40 % are wiring or connector issues that require a multimeter and patience. The PCM driver failing is rare; do not assume PCM is the cause until everything else has been ruled out.
Why OCV connectors fail in the oil-rich engine bay
The exhaust-side OCV sits on top of the cylinder head — high heat, oil mist, and constant vibration. Standard connector seals harden and crack within 8–10 years of normal use, letting oil migrate up the harness and into the connector. The fix is the connector or the sub-harness, not the OCV.