P0720 on a 2012 Jeep Grand Cherokee
Transmission Output Speed Sensor Malfunction
P0720 on a 2012 Jeep Grand Cherokee means transmission output speed sensor malfunction. P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis. Use the symptoms and test results to narrow down the cause before replacing parts.
What does P0720 mean on a 2012 Jeep Grand Cherokee?
P0720 is set when the transmission control module does not receive a valid signal from the output shaft speed sensor. The TCM uses this signal to compare actual transmission output to expected output for the selected gear and engine RPM — if the signal is missing or implausible, gear ratio calculations fail and the TCM cannot shift correctly. The vehicle typically drops into limp mode (stuck in a default gear, often 3rd or 4th) until the signal is restored.
The symptoms, causes, and diagnostic steps below describe P0720 itself, so they read the same on nearby Jeep Grand Cherokee model years. Powertrain and trim details vary year to year — confirm the specifics against your own vehicle before buying parts.
Is it safe to drive a 2012 Jeep Grand Cherokee with P0720?
P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.
What are the symptoms of P0720 on a 2012 Jeep Grand Cherokee?
- Check Engine Light is illuminated
- Speedometer reads zero or fluctuates erratically
- Transmission locked into a single gear (limp mode)
- Hard, harsh, or no shifts
- Cruise control inoperative
- Vehicle may shudder or hesitate at the moment of shift
- Often paired with P0700 (transmission control malfunction)
What causes P0720 on a 2012 Jeep Grand Cherokee?
Possible causes of P0720 depend on the equipment fitted. Confirm which parts and tests apply on a 2012 Jeep Grand Cherokee before pricing a repair.
| Cause | Estimated repair (USD) |
|---|---|
| Failed output shaft speed sensor element | $150–$500 |
| Damaged sensor connector or harness | $80–$350 |
| Metal debris on the sensor tip (from internal transmission wear) Cleaning the sensor face is a free first attempt. | $100–$400 |
| Damaged tone ring or reluctor wheel inside the transmission | $1,500–$4,500 |
| Transmission fluid contamination preventing the sensor from reading | $200–$700 |
| Wiring fault between the sensor and the TCM | $100–$500 |
| Failed TCM signal input (rare) | $500–$1,500 |
These are editorial estimates in U.S. dollars. A shop can price a confirmed repair using the engine, parts and local labor rate.
How to diagnose this on a 2012 Jeep Grand Cherokee
-
Locate the output speed sensor on this transmission
The output shaft speed sensor is typically a two-wire sensor threaded into the rear of the transmission case (RWD vehicles) or the side of the transaxle (FWD vehicles). Some vehicles have it on the transfer case for 4WD. Confirm location in the service manual.
Tools: Vehicle-specific service information
-
Check connector and visible wiring
Sensor connectors near the transmission case are exposed to heat, road debris, and sometimes fluid leaks. Unplug and inspect for corrosion, transmission fluid migration up the harness, or visible damage. Clean and re-seat.
Tools: Connector unlock tool, Electrical contact cleaner
-
Measure sensor resistance
Most output speed sensors are magnetic or Hall-effect with a typical resistance of 200–1500 Ω. Compare to the service manual. Infinite resistance means an open sensor; near zero means shorted. Either way, replace.
Tools: Multimeter, Service spec sheet
-
Verify signal output during rotation
On a lift with the rear wheels free to rotate, spin a rear wheel slowly by hand while watching the output speed PID. The reading should change in proportion to wheel rotation. No response confirms a dead sensor or damaged tone ring.
Tools: Vehicle lift, Scan tool with output speed PID
-
Inspect sensor tip for debris
Remove the sensor and look at the magnetic tip. Steel slivers stuck to the magnet are normal — large chunks or clutch material is a warning sign that the transmission is shedding material. Clean the tip and reinstall as a first attempt; consider transmission fluid analysis if heavy debris was present.
Tools: Socket, Magnet pick or wire brush
NHTSA complaints & recalls for the 2012 Jeep Grand Cherokee
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Jeep Grand Cherokee. Use these to gauge how common a problem is on your specific vehicle before you start chasing Jeep Grand Cherokee diagnostics.
NHTSA snapshot taken October 21, 2026; refreshed quarterly. For live figures see NHTSA.gov .
- ENGINE 285
- POWER TRAIN 102
- ELECTRICAL SYSTEM 837
- SERVICE BRAKES 278
- FUEL/PROPULSION SYSTEM 216
10 active recalls
- ELECTRICAL SYSTEM Nov 2019
Chrysler (FCA US LLC) is recalling certain 2011-2013 Dodge Durango and Jeep Grand Cherokee vehicles equipped with a 3.6, 5.7, or 6.4 liter engine and previously recalled under NHTSA Recall 14V530 or 15V115. The fuel pump relay inside the Totally Integrated Power Module (TIPM-7) m…
NHTSA campaign 19V813000 - SERVICE BRAKES Sep 2017
Chrysler (FCA US LLC) is recalling certain 2011-2014 Dodge Durango and Jeep Grand Cherokee vehicles. The affected vehicles had brake booster shields installed under a previous campaign to prevent water from entering the brake booster and limiting braking ability. This recall is t…
NHTSA campaign 17V572000 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR Jul 2017
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Challenger, Dodge Charger, Chrysler 300, Dodge Durango, and 2012-2014 Jeep Grand Cherokee vehicles. The affected vehicles have electro-hydraulic power steering (EHPS) and are equipped with a 5.7L or a 3.6L engi…
NHTSA campaign 17V435000 - ELECTRICAL SYSTEM:WIRING Dec 2015
Chrysler (FCA US LLC) is recalling certain model year 2011-2013 Dodge Durango and Jeep Grand Cherokee vehicles manufactured December 3, 2009, to September 1, 2012. In the affected vehicles, the wiring for the vanity lamp in the sun visor may short circuit, after having been remed…
NHTSA campaign 15V879000
How do I fix P0720 on a 2012 Jeep Grand Cherokee?
- Clean debris off the output speed sensor tip
- Replace the output shaft speed sensor with an OEM part
- Repair sensor connector or harness damage
- Service transmission fluid (drop pan, replace filter and gasket)
- Internal transmission repair if tone ring or shaft damage is confirmed
Engines in the 2012 Jeep Grand Cherokee
The 2012 Jeep Grand Cherokee was offered with the 3.6L 6-cylinder, 5.7L 8-cylinder and 6.4L 8-cylinder engines. Which one you have changes where P0720 is most likely to originate, so confirm your engine before ordering parts.
Engine data: EPA fueleconomy.gov.
Why P0720 puts the transmission into limp mode
The TCM continuously compares output shaft speed to engine RPM and selected gear to verify it is actually getting the gear ratio it commanded. Without a valid output speed signal:
- Ratio verification fails (sets P0731-P0734 in some cases)
- Shift point timing breaks (cannot tell vehicle speed for upshifts)
- Torque converter lockup logic fails (depends on accurate speed)
A transmission may restrict shifting when the output-speed signal is lost. If acceleration or gear engagement is unpredictable, stop safely and arrange assistance. Follow the instructions for the warning displayed on your vehicle.
P0720 with metal on the sensor tip
A small amount of metallic dust on the magnetic sensor tip is normal — it’s the natural wear of bearings and gears over the life of the transmission. Large flakes or clutch material is not normal and indicates internal damage that will eventually cause shifting problems beyond the sensor. If you find heavy debris, do a fluid service and inspect the pan magnet too — together they tell the story of what’s happening inside.
P0720 vs P0500 (Vehicle Speed Sensor)
These can look similar but come from different sources:
- P0500 — vehicle speed signal missing (often the ABS wheel speed sensor on modern vehicles)
- P0720 — transmission output shaft speed signal missing specifically from the transmission’s own sensor
On vehicles where the TCM derives “vehicle speed” from the output shaft sensor, both codes can set together from a single sensor failure.
P0720 on a 2012 Jeep Grand Cherokee: frequently asked questions
What does diagnostic trouble code P0720 mean on a 2012 Jeep Grand Cherokee?
P0720 is set when the transmission control module does not receive a valid signal from the output shaft speed sensor. The TCM uses this signal to compare actual transmission output to expected output for the selected gear and engine RPM — if the signal is missing or implausible, gear ratio calculations fail and the TCM cannot shift correctly. The vehicle typically drops into limp mode (stuck in a default gear, often 3rd or 4th) until the signal is restored.
What are the symptoms of P0720 on a 2012 Jeep Grand Cherokee?
Check Engine Light is illuminated. Speedometer reads zero or fluctuates erratically. Transmission locked into a single gear (limp mode). Hard, harsh, or no shifts. Cruise control inoperative. Vehicle may shudder or hesitate at the moment of shift. Often paired with P0700 (transmission control malfunction)
What causes P0720 on a 2012 Jeep Grand Cherokee?
Failed output shaft speed sensor element (estimated U.S. repair cost $150–$500). Damaged sensor connector or harness (estimated U.S. repair cost $80–$350). Metal debris on the sensor tip (from internal transmission wear) (estimated U.S. repair cost $100–$400). Damaged tone ring or reluctor wheel inside the transmission. Transmission fluid contamination preventing the sensor from reading. Wiring fault between the sensor and the TCM. Failed TCM signal input (rare)
Is it safe to drive a 2012 Jeep Grand Cherokee with P0720?
P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.