P0700 on a 2012 Jeep Grand Cherokee
Transmission Control System Malfunction
P0700 on a 2012 Jeep Grand Cherokee means transmission control system malfunction. P0700 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis. Use the symptoms and test results to narrow down the cause before replacing parts.
What does P0700 mean on a 2012 Jeep Grand Cherokee?
P0700 is an "informational" code set by the engine control module when the transmission control module (TCM) reports any fault. P0700 itself does not identify a specific transmission problem — it is a flag that tells you to scan the TCM for the underlying code or codes. The actual fault could be anything from a shift solenoid failure to a slipping clutch pack to a low-fluid condition.
The symptoms, causes, and diagnostic steps below describe P0700 itself, so they read the same on nearby Jeep Grand Cherokee model years. Powertrain and trim details vary year to year — confirm the specifics against your own vehicle before buying parts.
Is it safe to drive a 2012 Jeep Grand Cherokee with P0700?
P0700 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.
What are the symptoms of P0700 on a 2012 Jeep Grand Cherokee?
- Check Engine Light is illuminated
- Transmission stuck in a single gear (often 3rd or 4th — "limp mode")
- Hard, delayed, or erratic shifts
- Torque converter clutch not locking up on the highway
- Higher than normal RPM at cruise
- Reduced fuel economy
- Possible transmission slipping under load
What causes P0700 on a 2012 Jeep Grand Cherokee?
Possible causes of P0700 depend on the equipment fitted. Confirm which parts and tests apply on a 2012 Jeep Grand Cherokee before pricing a repair.
| Cause | Estimated repair (USD) |
|---|---|
| Low or burnt transmission fluid Always check fluid level and condition first; many P0700s clear with a fluid and filter service. | $100–$350 |
| Failed shift solenoid (one or more) | $250–$900 |
| Failed transmission speed sensor (input or output) | $150–$500 |
| Worn or stuck valve body | $600–$2,000 |
| Internal mechanical wear — slipping clutch packs or bands | $2,500–$6,000 |
| Failed transmission control module (TCM) itself | $500–$1,500 |
| Wiring harness damage to TCM or solenoid pack | $200–$700 |
These are editorial estimates in U.S. dollars. A shop can price a confirmed repair using the engine, parts and local labor rate.
How to diagnose this on a 2012 Jeep Grand Cherokee
-
Scan the TCM for the specific transmission code
P0700 alone is not actionable. Use a scan tool capable of reading transmission codes (not just engine codes) to retrieve the actual P07XX, P08XX, or P09XX code that triggered the P0700. That code is what to act on.
Tools: Scan tool with TCM access
-
Check fluid level, color, and smell
Most modern transmissions require checking fluid at operating temperature with the engine running and the selector in park or neutral, on a level surface. Dark, brown, or burnt-smelling fluid indicates clutch material in the fluid — fix the root cause; do not just refill.
Tools: Lift or jack and stands (sealed-for-life units), Vehicle-specific fluid spec
-
Inspect the wiring at the transmission case
The external transmission harness is exposed to heat, oil, and road debris. Disconnect, inspect, and reconnect every external connector. A connector full of transmission fluid points to a leaking case seal that has wicked fluid up the harness — replace the seal and sometimes the harness.
Tools: Connector unlock tool, Electrical cleaner
-
Pan-drop and inspect the filter and magnet
Drop the pan and inspect the filter, gasket sealing surface, and the magnet on the bottom of the pan. A magnet covered in fine metallic paste is normal. Large chunks of metal or clutch material indicate internal failure — at that point a teardown or replacement is required.
Tools: Drain pan, Socket set, New filter and gasket
-
Verify TCM and ECM are talking on the CAN bus
Use the scan tool to read live data from both modules simultaneously. If the ECM sees a vehicle speed that disagrees with the TCM, suspect a speed sensor or harness fault. If the TCM is non-responsive, check power, ground, and CAN bus continuity to the module.
Tools: Scan tool with bi-module live data, Multimeter
NHTSA complaints & recalls for the 2012 Jeep Grand Cherokee
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Jeep Grand Cherokee. Use these to gauge how common a problem is on your specific vehicle before you start chasing Jeep Grand Cherokee diagnostics.
NHTSA snapshot taken October 21, 2026; refreshed quarterly. For live figures see NHTSA.gov .
- ENGINE 285
- POWER TRAIN 102
- ELECTRICAL SYSTEM 837
- SERVICE BRAKES 278
- FUEL/PROPULSION SYSTEM 216
10 active recalls
- ELECTRICAL SYSTEM Nov 2019
Chrysler (FCA US LLC) is recalling certain 2011-2013 Dodge Durango and Jeep Grand Cherokee vehicles equipped with a 3.6, 5.7, or 6.4 liter engine and previously recalled under NHTSA Recall 14V530 or 15V115. The fuel pump relay inside the Totally Integrated Power Module (TIPM-7) m…
NHTSA campaign 19V813000 - SERVICE BRAKES Sep 2017
Chrysler (FCA US LLC) is recalling certain 2011-2014 Dodge Durango and Jeep Grand Cherokee vehicles. The affected vehicles had brake booster shields installed under a previous campaign to prevent water from entering the brake booster and limiting braking ability. This recall is t…
NHTSA campaign 17V572000 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR Jul 2017
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Challenger, Dodge Charger, Chrysler 300, Dodge Durango, and 2012-2014 Jeep Grand Cherokee vehicles. The affected vehicles have electro-hydraulic power steering (EHPS) and are equipped with a 5.7L or a 3.6L engi…
NHTSA campaign 17V435000 - ELECTRICAL SYSTEM:WIRING Dec 2015
Chrysler (FCA US LLC) is recalling certain model year 2011-2013 Dodge Durango and Jeep Grand Cherokee vehicles manufactured December 3, 2009, to September 1, 2012. In the affected vehicles, the wiring for the vanity lamp in the sun visor may short circuit, after having been remed…
NHTSA campaign 15V879000
How do I fix P0700 on a 2012 Jeep Grand Cherokee?
- Service the transmission fluid and filter to OEM specification
- Replace failed shift solenoid(s)
- Replace failed input or output speed sensor
- Replace or rebuild the valve body
- Replace the TCM
- Major rebuild or replacement of the transmission for internal failures
Engines in the 2012 Jeep Grand Cherokee
The 2012 Jeep Grand Cherokee was offered with the 3.6L 6-cylinder, 5.7L 8-cylinder and 6.4L 8-cylinder engines. Which one you have changes where P0700 is most likely to originate, so confirm your engine before ordering parts.
Engine data: EPA fueleconomy.gov.
P0700 repair guides
Why P0700 by itself is not a diagnosis
P0700 is set in the ECM because the TCM reported a problem. The TCM stored the actual code. Many cheap OBD-II scanners only read engine codes — they will show P0700 with no further detail, leading to wasted parts swaps. A scan tool that can read transmission codes is essential for diagnosing P0700 efficiently.
P0700 with limp mode (stuck in one gear)
Some transmissions limit gear selection when the control module detects a fault. P0700 alone does not identify the affected gear or whether the vehicle can maintain speed. If it slips, loses drive or cannot respond predictably, stop safely and arrange assistance.
When to fluid-service vs rebuild
If the underlying transmission code is for a solenoid, sensor, or wiring issue and the fluid is clean, a fluid and filter service plus the failed electrical part is the right repair. If the underlying code is for ratio incorrect (P0731–P0734), torque converter clutch (P0741), or excessive clutch slip, the transmission has mechanical wear and a full rebuild or replacement is more cost-effective than chasing individual parts.
P0700 on a 2012 Jeep Grand Cherokee: frequently asked questions
What does diagnostic trouble code P0700 mean on a 2012 Jeep Grand Cherokee?
P0700 is an "informational" code set by the engine control module when the transmission control module (TCM) reports any fault. P0700 itself does not identify a specific transmission problem — it is a flag that tells you to scan the TCM for the underlying code or codes. The actual fault could be anything from a shift solenoid failure to a slipping clutch pack to a low-fluid condition.
What are the symptoms of P0700 on a 2012 Jeep Grand Cherokee?
Check Engine Light is illuminated. Transmission stuck in a single gear (often 3rd or 4th — "limp mode"). Hard, delayed, or erratic shifts. Torque converter clutch not locking up on the highway. Higher than normal RPM at cruise. Reduced fuel economy. Possible transmission slipping under load
What causes P0700 on a 2012 Jeep Grand Cherokee?
Low or burnt transmission fluid (estimated U.S. repair cost $100–$350). Failed shift solenoid (one or more) (estimated U.S. repair cost $250–$900). Failed transmission speed sensor (input or output) (estimated U.S. repair cost $150–$500). Worn or stuck valve body. Internal mechanical wear — slipping clutch packs or bands. Failed transmission control module (TCM) itself. Wiring harness damage to TCM or solenoid pack
Is it safe to drive a 2012 Jeep Grand Cherokee with P0700?
P0700 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.