P0700 on a 2017 Kia Forte
Transmission Control System Malfunction
P0700 on a 2017 Kia Forte indicates transmission control system malfunction. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is low or burnt transmission fluid (typically $100–$350). Confirm the root cause before replacing parts.
What does P0700 mean on a 2017 Kia Forte?
P0700 is an "informational" code set by the engine control module when the transmission control module (TCM) reports any fault. P0700 itself does not identify a specific transmission problem — it is a flag that tells you to scan the TCM for the underlying code or codes. The actual fault could be anything from a shift solenoid failure to a slipping clutch pack to a low-fluid condition.
This guide covers P0700 across the 2015-2019 Kia Forte generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Kia Forte with P0700?
In most cases a 2017 Kia Forte stays drivable for short trips with P0700 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0700 on a 2017 Kia Forte?
- Check Engine Light is illuminated
- Transmission stuck in a single gear (often 3rd or 4th — "limp mode")
- Hard, delayed, or erratic shifts
- Torque converter clutch not locking up on the highway
- Higher than normal RPM at cruise
- Reduced fuel economy
- Possible transmission slipping under load
What causes P0700 on a 2017 Kia Forte?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Low or burnt transmission fluid Always check fluid level and condition first; many P0700s clear with a fluid and filter service. | Most common | $100–$350 |
| Failed shift solenoid (one or more) | Common | $250–$900 |
| Failed transmission speed sensor (input or output) | Common | $150–$500 |
| Worn or stuck valve body | Occasional | $600–$2,000 |
| Internal mechanical wear — slipping clutch packs or bands | Occasional | $2,500–$6,000 |
| Failed transmission control module (TCM) itself | Rare | $500–$1,500 |
| Wiring harness damage to TCM or solenoid pack | Occasional | $200–$700 |
How to diagnose this on a 2017 Kia Forte
-
Scan the TCM for the specific transmission code
P0700 alone is not actionable. Use a scan tool capable of reading transmission codes (not just engine codes) to retrieve the actual P07XX, P08XX, or P09XX code that triggered the P0700. That code is what to act on.
Tools: Scan tool with TCM access
-
Check fluid level, color, and smell
Most modern transmissions require checking fluid at operating temperature with the engine running and the selector in park or neutral, on a level surface. Dark, brown, or burnt-smelling fluid indicates clutch material in the fluid — fix the root cause; do not just refill.
Tools: Lift or jack and stands (sealed-for-life units), Vehicle-specific fluid spec
-
Inspect the wiring at the transmission case
The external transmission harness is exposed to heat, oil, and road debris. Disconnect, inspect, and reconnect every external connector. A connector full of transmission fluid points to a leaking case seal that has wicked fluid up the harness — replace the seal and sometimes the harness.
Tools: Connector unlock tool, Electrical cleaner
-
Pan-drop and inspect the filter and magnet
Drop the pan and inspect the filter, gasket sealing surface, and the magnet on the bottom of the pan. A magnet covered in fine metallic paste is normal. Large chunks of metal or clutch material indicate internal failure — at that point a teardown or replacement is required.
Tools: Drain pan, Socket set, New filter and gasket
-
Verify TCM and ECM are talking on the CAN bus
Use the scan tool to read live data from both modules simultaneously. If the ECM sees a vehicle speed that disagrees with the TCM, suspect a speed sensor or harness fault. If the TCM is non-responsive, check power, ground, and CAN bus continuity to the module.
Tools: Scan tool with bi-module live data, Multimeter
NHTSA complaints & recalls for the 2017 Kia Forte
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Kia Forte. Use these to gauge how common a problem is on your specific vehicle before you start chasing Kia Forte diagnostics.
- ENGINE 143
- UNKNOWN OR OTHER 49
- ELECTRICAL SYSTEM 45
- EXTERIOR LIGHTING 43
- FUEL/PROPULSION SYSTEM 29
3 active recalls
- AIR BAGS Jan 2022
Kia Motors America (Kia) is recalling certain 2017-2019 Sedona, Soul, Soul EV, 2017-2018 Forte, and 2017 Forte Koup vehicles. The Air Bag Control Unit (ACU) cover may contact a memory chip on the printed circuit board and damage the electrical circuit. Circuit damage may result…
NHTSA campaign 22V031000 - LATCHES/LOCKS/LINKAGES:TRUNK LID:LATCH Aug 2021
Kia Motors America (Kia) is recalling certain 2016-2018 Forte 4-door, Forte Koup 2-door, and 2018-2019 Rio 4-door vehicles. The trunk latch may become damaged, preventing the opening of the trunk from the inside. As such, these vehicles fail to comply with the requirements of F…
NHTSA campaign 21V622000 - ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PUMP Apr 2021
Kia Motors America (Kia) is recalling certain 2017-2018 Forte vehicles equipped with a 2.0L Nu MPI engine. Foreign particles may stick inside the oil pump, which may cause an oil pump failure and engine damage.…
NHTSA campaign 21V260000
How do I fix P0700 on a 2017 Kia Forte?
- Service the transmission fluid and filter to OEM specification
- Replace failed shift solenoid(s)
- Replace failed input or output speed sensor
- Replace or rebuild the valve body
- Replace the TCM
- Major rebuild or replacement of the transmission for internal failures
About the 2015-2019 Kia Forte
The 2015-2019 Kia Forte was commonly sold with the following powertrains: 2.0L I4, 1.6L Turbo I4. Common trims include LX, LXS, GT-Line, GT.
Why P0700 by itself is not a diagnosis
P0700 is set in the ECM because the TCM reported a problem. The TCM stored the actual code. Many cheap OBD-II scanners only read engine codes — they will show P0700 with no further detail, leading to wasted parts swaps. A scan tool that can read transmission codes is essential for diagnosing P0700 efficiently.
P0700 with limp mode (stuck in one gear)
When the TCM detects a fault that could damage the transmission, it commands a default gear (often 3rd or 4th) and disables all shifting. This is “limp mode.” It is meant to let you drive a short distance to a shop, not for daily driving. Continuing to drive in limp mode for weeks can damage internal components even though the limp logic exists to prevent damage.
When to fluid-service vs rebuild
If the underlying transmission code is for a solenoid, sensor, or wiring issue and the fluid is clean, a fluid and filter service plus the failed electrical part is the right repair. If the underlying code is for ratio incorrect (P0731–P0734), torque converter clutch (P0741), or excessive clutch slip, the transmission has mechanical wear and a full rebuild or replacement is more cost-effective than chasing individual parts.