P0606 on a 2012 Jeep Grand Cherokee

PCM Internal Processor Fault

P0606 on a 2012 Jeep Grand Cherokee indicates pcm internal processor fault. Stop driving and diagnose it before continuing — it can signal an unsafe condition. The most common cause is low battery voltage or weak battery causing pcm brown-out (typically $100–$350). Confirm the root cause before replacing parts.

Severity: high Do not drive Mid-size SUV 2010-2014 Jeep Grand Cherokee

Reviewed by MECH AI Editorial · Last verified May 25, 2026

What does P0606 mean on a 2012 Jeep Grand Cherokee?

P0606 is set when the engine control module's internal self-test detects an inconsistency in its own processor — typically a RAM test, ROM checksum, watchdog timeout, or processor brown-out. Unlike most OBD-II codes which point to an external sensor or actuator, P0606 is the PCM saying "something is wrong with me." The cause is usually a power or ground issue, water intrusion, or the PCM itself failing.

This guide covers P0606 across the 2010-2014 Jeep Grand Cherokee generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.

Is it safe to drive a 2012 Jeep Grand Cherokee with P0606?

No. P0606 is a high-severity code on the 2012 Jeep Grand Cherokee — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.

What are the symptoms of P0606 on a 2012 Jeep Grand Cherokee?

Check Engine Light is illuminated
Reduced engine power / limp mode
Erratic or random drivability issues
Multiple unrelated codes setting simultaneously
Hard starting or no-start
Loss of communication with scan tool intermittently
Random stalling

What causes P0606 on a 2012 Jeep Grand Cherokee?

Cause	Likelihood	Estimated repair (USD)
Low battery voltage or weak battery causing PCM brown-out Always test battery and charging before condemning the PCM.	Most common	$100–$350
Corroded or loose PCM power / ground connection	Common	$50–$250
Water intrusion into the PCM enclosure	Common	$400–$1,500
Failed PCM module (internal electronics)	Common	$500–$1,500
Failed alternator producing dirty / noisy charging voltage	Occasional	$200–$700
Software corruption requiring reflash	Occasional	$100–$400

How to diagnose this on a 2012 Jeep Grand Cherokee

Test the battery and charging system FIRST

P0606 from low voltage is the most common cause and the cheapest fix. A battery weaker than 12.4 V at rest, or charging voltage below 13.5 V at idle, can brown out the PCM and set P0606. Replace the battery or repair the alternator before touching the PCM.

Tools: Multimeter, Battery load tester
Check PCM power and ground connections

Locate the PCM (typically under the hood near the firewall, or under the dash). Inspect every connector for corrosion, bent pins, or water damage. Verify all ground straps from the engine and PCM are tight to clean bare metal. Loose grounds cause classic intermittent P0606.

Tools: Multimeter, Wire brush, Electrical contact cleaner
Inspect the PCM for water intrusion

Remove the PCM and inspect the case seam, connector seals, and the PCB visible through any vents. Green corrosion on the board confirms water damage — replacement is the only fix at that point. Common entry points: cowl drain blockage, rear-vent seal failure, or aftermarket sunroof drain issues.

Tools: Socket set, Inspection light
Read all codes from all modules

P0606 alone is one thing; P0606 with codes from 3+ other modules (TCM, ABS, BCM) usually points at a shared cause like low system voltage. Pull codes from every module before deciding the PCM is the problem.

Tools: Scan tool with multi-module access
Try a PCM reflash before replacement

Sometimes P0606 is caused by software corruption — particularly after a battery disconnect or jump-start with reversed polarity. A dealer or independent shop with the correct programming software can attempt a reflash for a fraction of the replacement cost.

Tools: OEM scan tool or J2534 reprogramming setup

NHTSA complaints & recalls for the 2012 Jeep Grand Cherokee

Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Jeep Grand Cherokee. Use these to gauge how common a problem is on your specific vehicle before you start chasing Jeep Grand Cherokee diagnostics.

1,633 owner complaints

46 involved a crash

104 involved a fire

35 reported injuries

ENGINE 282
POWER TRAIN 101
ELECTRICAL SYSTEM 834
SERVICE BRAKES 305
FUEL/PROPULSION SYSTEM 215

11 active recalls

ELECTRICAL SYSTEM Nov 2019

Chrysler (FCA US LLC) is recalling certain 2011-2013 Dodge Durango and Jeep Grand Cherokee vehicles equipped with a 3.6, 5.7, or 6.4 liter engine and previously recalled under NHTSA Recall 14V530 or 15V115. The fuel pump relay inside the Totally Integrated Power Module (TIPM-7)…
NHTSA campaign 19V813000
ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR Jul 2017

Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Challenger, Dodge Charger, Chrysler 300, Dodge Durango, and 2012-2014 Jeep Grand Cherokee vehicles. The affected vehicles have electro-hydraulic power steering (EHPS) and are equipped with a 5.7L or a 3.6L eng…
NHTSA campaign 17V435000
ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER Oct 2017

Accessible Technologies, Inc. (ATI) is recalling certain ProCharger Superchargers, model numbers AB037A-100, AB037A-100P, and A037A-100B, sold for installation on 2012-2017 Jeep Grand Cherokee SRT8 and SRT vehicles. The supercharger mounting bracket may contact and damage the AB…
NHTSA campaign 17E061000
SERVICE BRAKES Sep 2017

Chrysler (FCA US LLC) is recalling certain 2011-2014 Dodge Durango and Jeep Grand Cherokee vehicles. The affected vehicles had brake booster shields installed under a previous campaign to prevent water from entering the brake booster and limiting braking ability. This recall is…
NHTSA campaign 17V572000

How do I fix P0606 on a 2012 Jeep Grand Cherokee?

Replace the battery and / or alternator
Clean and re-tighten all PCM power and ground connections
Repair water intrusion source and replace the PCM
Replace the PCM with a programmed unit
Reflash the PCM software

About the 2010-2014 Jeep Grand Cherokee

The 2010-2014 Jeep Grand Cherokee was commonly sold with the following powertrains: 3.6L Pentastar V6, 5.7L HEMI V8, 3.0L EcoDiesel V6. Common trims include Laredo, Limited, Overland, Summit.

Why a weak battery sets P0606

Modern engine control modules require stable voltage to run their internal self-tests. When voltage dips below approximately 9 V during a crank — even briefly — the PCM may reset, fail an internal check, and store P0606 as evidence of the brown-out. This is so common that “load-test the battery” is always the first diagnostic step. Replacing a $120 battery has resolved more P0606 codes than any other single repair.

Water intrusion and the cowl drain

A clogged cowl drain (the drain that lets rainwater out from under the windshield wipers) can let water pool against the firewall — directly above where many vehicles mount the PCM. Over time water wicks into the connector and corrodes the board. Always check the cowl drain when investigating P0606, especially on vehicles parked outdoors and on those with visible water staining inside the cabin.

PCM replacement is the last resort

A PCM costs $400–$1,500 and must usually be programmed and keyed to the vehicle before it will run. Try every cheaper cause first:

Battery and charging system test
Power and ground connection inspection
Multi-module code scan
Software reflash

Only after all of those fail should the PCM itself be condemned. Refurbished and remanufactured PCMs are available at 30–50 % of new prices and are sometimes a better choice on older vehicles.