P0507 on a 2017 Toyota Camry
Idle Higher Than Expected
What does P0507 mean on a 2017 Toyota Camry?
P0507 is set when the ECM commands the throttle to a specific idle RPM and measures actual idle higher than that target by more than a calibrated amount (typically 200+ RPM higher). The cause is almost always unmetered air entering the engine — a vacuum leak somewhere — or a stuck throttle body / idle control issue.
Symptoms on a 2017 Toyota Camry
- Check Engine Light is illuminated
- Engine idles noticeably high (1000-1500 RPM instead of 700-900)
- Possible whistling or hissing sound from the intake area
- Reduced fuel economy
- Hesitation as the engine tries to slow when stopping
- May be paired with P0171 (lean code)
Likely causes on a 2017 Toyota Camry
- Vacuum leak (intake gasket, PCV hose, brake-booster hose, throttle-body gasket) Most commonEstimated repair: $80– $600
Most P0507 codes trace to unmetered air entering the engine.
- Carbon-coked throttle body keeping the blade slightly open CommonEstimated repair: $20– $200
- Failed or sticking idle air control (IAC) valve on older non-ETC vehicles CommonEstimated repair: $80– $300
- Failed throttle body needing replacement and relearn OccasionalEstimated repair: $250– $800
- Sticking accelerator pedal or throttle cable (older vehicles) OccasionalEstimated repair: $50– $250
- Cracked plastic intake manifold OccasionalEstimated repair: $250– $900
- EVAP purge valve stuck open (often sets P0496 alongside) OccasionalEstimated repair: $80– $300
How to diagnose this on a 2017 Toyota Camry
-
Confirm the actual idle RPM and check fuel trims
Scan-tool live data should show actual idle RPM and the target. Look at Bank 1 LTFT: a high positive number (e.g. +15 % or more) confirms a real vacuum leak. Trims near zero with high idle point at a throttle body or EVAP issue rather than a leak.
Tools: Scan tool with live PIDs
-
Smoke-test the intake
Pressurize the intake with smoke through a snorkel cap or the throttle body. Watch every gasket, hose, vacuum tee, the brake booster line, the PCV system, and the EVAP purge line. Smoke escaping anywhere is the leak.
Tools: EVAP / intake smoke machine, Flashlight and inspection mirror
-
Inspect and clean the throttle body
Coked carbon at the throttle bore prevents the blade from closing fully — the engine pulls air around the blade that the ECM cannot fully control. Clean with throttle-body-safe cleaner (never carb cleaner) and a soft brush. Perform an idle relearn after.
Tools: Throttle body cleaner, Soft brush, Service manual for the relearn procedure
-
Test the IAC valve (non-ETC vehicles)
On older vehicles with a separate IAC valve, command the valve with a scan tool and watch for idle changes. A valve that does not respond, or that idles correctly with the connector unplugged, is stuck or failed.
Tools: Scan tool with IAC command
-
Verify the EVAP purge valve is not stuck open
A stuck-open purge valve introduces unmetered fuel vapor at idle, causing high idle and lean trims similar to a vacuum leak. With the engine idling, disconnect the purge valve — if idle smooths out, the purge valve is the cause.
Tools: Hose disconnect tools
Known Technical Service Bulletins for the 2015-2019 Toyota Camry
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Toyota Camry.
- ENGINE Feb 12, 2026
This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing a rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger.
NHTSA #11029893 - ENGINE Feb 12, 2026
OBSOLETE NOTICE February 13, 2026: This bulletin is now obsolete. Please see T-SB-0009-26.
NHTSA #11029892 - UNKNOWN OR OTHER Jan 6, 2026
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA #11028712 - ELECTRICAL SYSTEM Jun 12, 2025
The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.
NHTSA #11020657 - STRUCTURE Dec 5, 2024
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
NHTSA #11012743 - STRUCTURE Dec 5, 2024
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
NHTSA #11012744
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
Common fixes
- Repair vacuum leak(s) found by smoke test
- Clean the throttle body and perform idle relearn
- Replace the IAC valve (older vehicles)
- Replace the EVAP purge valve
- Replace cracked plastic intake manifold (model-specific)
About the 2015-2019 Toyota Camry
The 2015-2019 Toyota Camry was commonly sold with the following powertrains: 2.5L I4, 3.5L V6, 2.5L Hybrid I4. Common trims include LE, SE, XLE, XSE.
The vacuum leak almost certainly is the cause
P0507 paired with P0171 (or P0174) is virtually always a vacuum leak. The high idle and the lean fuel trim both result from the same underlying problem: unmetered air entering the engine downstream of the MAF. The ECM cannot identify exactly which leak path is responsible, only that one exists. Smoke testing is the fastest path to the source.
Common P0507 leak locations by engine
- Ford 4.6 / 5.4 modular V8 — cracked plastic intake manifold, PCV hose at the rear of the engine
- GM 3.6 LFX / LLT V6 — intake manifold gaskets, PCV system
- Toyota 2GR-FE V6 — throttle-body gasket, intake plenum bolts
- Honda K-series — IACV gasket, vacuum tee at the brake booster
- Chrysler 3.5 / 3.6 Pentastar — PCV tube, intake gasket
- Most vehicles 10+ years old — hardened brake-booster hose
Idle relearn after throttle body cleaning
Modern vehicles with electronic throttle control require an idle relearn after any throttle body removal, cleaning, or replacement. The procedure varies — generally:
- Battery disconnect 30+ seconds, reconnect
- Key on, engine off, 30 seconds
- Start engine, idle 5 minutes with no load (AC off, no electrical accessories)
- Drive a short cycle including a few full stops
Some vehicles require a bidirectional scan tool to perform the relearn. Without a successful relearn, P0507 will set again within a few drive cycles even though the throttle body is mechanically perfect.