P0500 on a 2012 Chevrolet Traverse
Vehicle Speed Sensor Malfunction
P0500 on a 2012 Chevrolet Traverse indicates vehicle speed sensor malfunction. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed transmission-mounted vehicle speed sensor (pre-can bus vehicles) (typically $100–$350). Confirm the root cause before replacing parts.
What does P0500 mean on a 2012 Chevrolet Traverse?
P0500 is set when the ECM does not see a valid vehicle speed signal, or sees a signal that does not correlate with engine RPM and selected gear. Modern vehicles derive vehicle speed from the ABS wheel speed sensors and broadcast it on the CAN bus; older vehicles use a dedicated transmission-mounted vehicle speed sensor (VSS). The fault source depends on which generation the vehicle is.
This guide covers P0500 across the 2010-2014 Chevrolet Traverse generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Chevrolet Traverse with P0500?
In most cases a 2012 Chevrolet Traverse stays drivable for short trips with P0500 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0500 on a 2012 Chevrolet Traverse?
- Check Engine Light is illuminated
- Speedometer reads zero or fluctuates erratically
- Odometer not accumulating miles
- Transmission may shift harshly or hold a gear too long
- Cruise control inoperative
- ABS or traction control lights may also be illuminated
- Possible speed-sensitive systems disabled (power steering assist on some EPS vehicles)
What causes P0500 on a 2012 Chevrolet Traverse?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed transmission-mounted vehicle speed sensor (pre-CAN bus vehicles) | Most common | $100–$350 |
| Failed ABS wheel speed sensor that feeds the ECM via CAN bus | Common | $150–$500 |
| Damaged or corroded VSS / wheel speed sensor connector | Common | $50–$250 |
| CAN bus wiring fault — message dropped between ABS module and PCM | Occasional | $100–$600 |
| Failed ABS control module | Occasional | $400–$1,500 |
| Damaged tone ring or reluctor wheel at the wheel hub | Occasional | $200–$700 |
| Failed instrument cluster on CAN-derived vehicles | Rare | $400–$1,200 |
How to diagnose this on a 2012 Chevrolet Traverse
-
Identify the vehicle speed source
Determine whether this vehicle uses a dedicated VSS on the transmission (typical for late-1990s through mid-2000s) or derives speed from the ABS wheel speed sensors. The service manual or the wiring diagram will tell you which. The diagnostic path differs significantly.
Tools: Vehicle-specific service information
-
Check for accompanying ABS or wheel-speed codes
On CAN-bus vehicles, P0500 with an ABS module code (C0035 family codes for individual wheel sensors) points directly at the failed wheel speed sensor. P0500 alone — no ABS codes — suggests either the dedicated VSS, the CAN bus message itself, or the ECM input.
Tools: Scan tool with multi-module access
-
Compare instrument cluster speed to scan tool speed
With the vehicle on a lift and the drive wheels spinning slowly in gear, compare the speedometer needle to the live vehicle speed PID on the scan tool. If they match but read zero, the source is the problem. If they disagree, the issue is in the signal path between the source and one of the consumers.
Tools: Scan tool, Vehicle lift or jack stands
-
Test the VSS or wheel speed sensor signal
For a transmission VSS, rotate the output shaft by hand or on a lift and watch the sensor output on the scan tool — it should produce a pulse for each rotation. For a wheel speed sensor, rotate the wheel slowly and watch its individual wheel speed PID.
Tools: Scan tool with raw sensor PIDs, Vehicle lift
-
Inspect the connector and wiring
VSS and wheel-speed sensor connectors live in harsh under-body environments. Water intrusion, road salt corrosion, and chafing against the brake hose are all common. Clean the connector pins, verify the harness routing, and re-test.
Tools: Electrical contact cleaner, Dielectric grease, Flashlight
NHTSA complaints & recalls for the 2012 Chevrolet Traverse
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Chevrolet Traverse. Use these to gauge how common a problem is on your specific vehicle before you start chasing Chevrolet Traverse diagnostics.
- ENGINE 115
- POWER TRAIN 46
- ELECTRONIC STABILITY CONTROL (ESC) 84
- STEERING 62
- ELECTRICAL SYSTEM 48
5 active recalls
- STRUCTURE:BODY:HATCHBACK/LIFTGATE Jun 2015
General Motors LLC (GM) is recalling certain model year 2008-2012 Buick Enclave vehicles manufactured January 3, 2007, to February 29, 2012, 2009-2012 Chevrolet Traverse vehicles manufactured July 6, 2008, to March 9, 2012, 2007-2012 GMC Acadia vehicles manufactured September 15,…
NHTSA campaign 15V415000 - SEAT BELTS May 2014
General Motors is recalling certain model year 2009-2014 Buick Enclave vehicles manufactured April 14, 2008, through May 14, 2014, Chevrolet Traverse vehicles manufactured June 6, 2008, through May 14, 2014, and GMC Acadia vehicles manufactured April 9, 2008, through May 14, 2014…
NHTSA campaign 14V266000 - AIR BAGS:SIDE/WINDOW Mar 2014
General Motors LLC (GM) is recalling certain model year 2008-2013 Buick Enclave and GMC Acadia and 2009-2013 Chevrolet Traverse and 2008-2010 Saturn Outlook vehicles. In the affected vehicles, increased resistance in the driver and passenger seat mounted side impact air bag (SIA…
NHTSA campaign 14V118000 - VISIBILITY:WINDSHIELD WIPER/WASHER:LINKAGES Apr 2012
GENERAL MOTORS (GM) IS RECALLING CERTAIN MODEL YEAR 2011-2012 CHEVROLET TRAVERSE, BUICK ENCLAVE, AND GMC ACADIA VEHICLES CURRENTLY REGISTERED IN ALASKA, COLORADO, CONNECTICUT, DELAWARE, IDAHO, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MONTANA,…
NHTSA campaign 12V151000
How do I fix P0500 on a 2012 Chevrolet Traverse?
- Replace the transmission-mounted vehicle speed sensor (older vehicles)
- Replace the failed ABS wheel speed sensor
- Repair damaged sensor wiring or connector
- Replace damaged tone ring / reluctor at the wheel hub
- Repair CAN bus wiring fault
- Replace ABS control module (only if confirmed bad)
About the 2010-2014 Chevrolet Traverse
The 2010-2014 Chevrolet Traverse was commonly sold with the following powertrains: 3.6L V6, 2.0L Turbo I4. Common trims include L, LS, LT, RS, Premier, High Country.
Why P0500 affects so many other systems
Vehicle speed is one of the most widely-shared signals on a modern vehicle. The ECM, TCM, ABS module, EPS module, instrument cluster, body control module, and infotainment all consume it. When it goes missing or invalid, multiple systems degrade simultaneously — and several warning lights illuminate, which can look like a much bigger problem than it really is.
The transmission VSS test (older vehicles)
On pre-CAN-bus vehicles, the VSS is typically a two-wire sensor mounted on the transmission tailshaft or transfer case. With the vehicle in neutral and the rear wheels off the ground, slowly rotate a rear wheel. A multimeter set to AC volts should show a small AC signal — typically 0.5–2 V — varying with rotation speed. No signal at all means the sensor or its tone ring is dead.
The wheel speed sensor test (modern vehicles)
Modern ABS-derived speed signals come from one of four wheel sensors that magnetically pick up a tone ring on the hub. The most common failure is a damaged tone ring after a wheel bearing replacement done without care. Always replace tone rings as a kit when servicing hubs on vehicles with this system.