P0456 on a 2017 Subaru Outback
EVAP Very Small Leak Detected
P0456 on a 2017 Subaru Outback indicates evap very small leak detected. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is worn fuel cap o-ring or wrong-spec cap (typically $15–$60). Confirm the root cause before replacing parts.
What does P0456 mean on a 2017 Subaru Outback?
P0456 is set when the EVAP system's very-small-leak monitor detects an opening approximately 0.020 inches (0.5 mm) or larger. This is finer than P0442 (0.040") and significantly harder to find — it can be a single pinhole, a hardened O-ring, or a hairline crack in a plastic component. The vehicle drives normally and there is rarely any fuel smell.
This guide covers P0456 across the 2015-2019 Subaru Outback generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Subaru Outback with P0456?
In most cases a 2017 Subaru Outback stays drivable for short trips with P0456 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0456 on a 2017 Subaru Outback?
- Check Engine Light is illuminated
- Almost never any drivability complaint
- Rarely any noticeable fuel smell (leak is too small)
- Vehicle will fail emissions / smog testing
What causes P0456 on a 2017 Subaru Outback?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Worn fuel cap O-ring or wrong-spec cap | Most common | $15–$60 |
| Aged or cracked EVAP hose elbows and quick-connect O-rings | Common | $30–$200 |
| Hairline crack in the charcoal canister body | Common | $200–$600 |
| Leaking EVAP purge valve seat (small internal leak only) | Occasional | $80–$300 |
| Fuel tank pressure sensor O-ring hardened | Occasional | $30–$150 |
| Pinhole at the fuel tank top — visible only with smoke or dye | Rare | $300–$1,200 |
How to diagnose this on a 2017 Subaru Outback
-
Replace the fuel cap with a fresh OEM-spec cap
A 0.020" leak at the cap costs $30 to rule out. Hand-tighten until the cap clicks at least 3 times. Drive several drive cycles so the monitor reruns. Many P0456 codes never come back after this step.
Tools: None
-
Smoke-test at the lowest pressure your machine supports
P0456 leaks are at the threshold of what smoke machines can find. Use the lowest pressure setting (0.5 psi or less). Let smoke build for 10 minutes. Inspect every quick-connect, O-ring, hose elbow, and canister seam with strong light. UV dye in the smoke fluid helps trace very faint trails.
Tools: EVAP smoke machine with UV dye, UV flashlight, Magnification glass
-
Read mode 6 EVAP test results
Mode 6 will show the recorded leak-decay rate from the last test. If the failure threshold is just barely exceeded, the leak is at the very small end — often a hardened O-ring or aged plastic. If the threshold is wildly exceeded, P0455 would normally set instead; P0456 with a large mode-6 deviation suggests the monitor calibration is off.
Tools: Scan tool with mode 6 support
-
Test the purge valve for an internal leak
Apply vacuum to the inlet side of the purge valve with the valve de-energized — it should hold vacuum indefinitely. A valve that slowly leaks vacuum is allowing fuel vapor through during engine-off, which the monitor sees as a system leak.
Tools: Hand vacuum pump
-
Verify the readiness monitor before re-testing
After any P0456 repair, drive 4–6 cold-start cycles with the tank between 25 % and 75 % full. Confirm the EVAP readiness monitor shows "complete" on the scan tool. A vehicle that passes a state smog test with the monitor "not ready" will not actually pass — most states fail vehicles with incomplete monitors.
Tools: Scan tool with readiness display
NHTSA complaints & recalls for the 2017 Subaru Outback
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Subaru Outback. Use these to gauge how common a problem is on your specific vehicle before you start chasing Subaru Outback diagnostics.
- POWER TRAIN 46
- ENGINE 42
- ELECTRICAL SYSTEM 391
- VISIBILITY/WIPER 205
- UNKNOWN OR OTHER 175
4 active recalls
- AIR BAGS: AIR BAG/RESTRAINT CONTROL MODULE Dec 2019
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.…
NHTSA campaign 19V910000 - SUSPENSION Aug 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabili…
NHTSA campaign 16V576000 - STEERING:COLUMN Oct 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.…
NHTSA campaign 16V716000 - STEERING:COLUMN May 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may…
NHTSA campaign 16V292000
How do I fix P0456 on a 2017 Subaru Outback?
- Replace the fuel cap
- Replace cracked EVAP hose elbows and aged O-rings
- Replace the EVAP charcoal canister
- Replace the EVAP purge valve
- Replace the fuel tank pressure sensor or its O-ring
About the 2015-2019 Subaru Outback
The 2015-2019 Subaru Outback was commonly sold with the following powertrains: 2.5L H4, 2.4L Turbo H4, 3.6L H6. Common trims include Base, Premium, Limited, Touring, Wilderness, Onyx Edition.
Why P0456 is the hardest EVAP code to diagnose
A 0.020-inch leak is roughly the size of a sewing needle hole. At atmospheric pressure that is essentially invisible. The only practical way to find it is with a smoke machine, UV dye, and patience — every joint, every gasket, every plastic seam. Shops typically charge a $100–$200 diagnostic fee for P0456 because the inspection takes 30–60 minutes even when you find the leak quickly.
P0456 vs. P0442
Same EVAP system, different leak-size threshold:
- P0442 ≈ 0.040” leak. Often a loose gas cap or visibly cracked hose.
- P0456 ≈ 0.020” leak. Almost never visible. Smoke-test mandatory.
A vehicle that previously set P0442 and now sets P0456 has had a leak get smaller — usually because someone tightened a cap or replaced a hose but missed the real source.
When the code keeps coming back
If P0456 returns within 30 days of a repair, the leak was not actually fixed — the monitor simply did not run again in the interim. Common overlooked sources: the spare-tire-mounted tank vent on certain trucks, the canister filter housing, and the seam where the fuel tank meets the filler neck on rust-belt vehicles.