P0411 on a 2022 Ford Bronco
Secondary Air Injection Insufficient Flow
P0411 on a 2022 Ford Bronco indicates secondary air injection insufficient flow. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed secondary air injection pump motor (typically $300–$1,200). Confirm the root cause before replacing parts.
What does P0411 mean on a 2022 Ford Bronco?
P0411 is set when the engine control module commands the secondary air injection (SAI) system to inject air into the exhaust during cold start and does not detect the expected oxygen reading at the upstream O2 sensors. The SAI system is a separate pump that blows fresh air into the exhaust manifold for the first 60–90 seconds after cold start, helping the catalyst light off faster and reducing cold-start emissions. P0411 means that air injection is not happening — usually because the SAI pump, check valve, or control valve has failed.
This guide covers P0411 across the 2020-2024 Ford Bronco generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Ford Bronco with P0411?
In most cases a 2022 Ford Bronco stays drivable for short trips with P0411 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0411 on a 2022 Ford Bronco?
- Check Engine Light is illuminated
- Whirring sound from the SAI pump during cold start (or absence of one)
- Slightly elevated cold-start emissions
- Vehicle will fail emissions / smog testing
- No noticeable drivability symptoms once warm
What causes P0411 on a 2022 Ford Bronco?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed secondary air injection pump motor Particularly common on VW, Audi, BMW, Porsche, and Mercedes vehicles. | Most common | $300–$1,200 |
| Stuck or seized SAI combination valve / check valve | Common | $200–$700 |
| SAI vacuum control solenoid failure | Common | $80–$350 |
| Cracked or disconnected SAI hose | Common | $50–$300 |
| Carbon-clogged SAI passages in the exhaust manifold | Occasional | $400–$1,500 |
| Failed SAI relay | Occasional | $30–$150 |
| Wiring fault to the SAI pump or solenoid | Occasional | $80–$350 |
How to diagnose this on a 2022 Ford Bronco
-
Listen for the SAI pump on cold start
On a cold engine (sat overnight), start the vehicle and listen for the SAI pump — a distinct whirring or humming sound from under the hood for 60–90 seconds. Silence at cold start means the pump is not running. Note: SAI does not operate on warm restarts, so the test only works on a truly cold engine.
Tools: Cold engine (sat overnight)
-
Test the SAI pump electrically
Locate the SAI pump (often in the engine bay or under a fender liner). Disconnect the connector and apply 12 V directly. A working pump runs immediately. Silence confirms a dead pump.
Tools: Jumper wires, 12 V supply (battery)
-
Inspect the SAI hose
Trace the air hose from the pump to the exhaust manifold area. Cracks, splits, or disconnections are common — especially on rubber hoses that have spent 10+ years near hot exhaust components. A failed hose means the pump runs but no air reaches the exhaust.
Tools: Flashlight, Inspection mirror
-
Test the combination / check valve
The SAI combination valve prevents exhaust from back-feeding into the pump. Remove and inspect — should freely allow air in one direction and seal in the other. Carbon buildup on the valve from years of exhaust exposure is the typical failure mode.
Tools: Service manual procedure, Carb cleaner
-
Read freeze-frame conditions
Note the engine temperature, vehicle speed, and time-since- start in the freeze frame. P0411 only sets within the cold- start enrichment window. If freeze frame shows the engine already warm, suspect a sensor or wiring issue rather than the pump itself.
Tools: Scan tool with freeze-frame data
NHTSA complaints & recalls for the 2022 Ford Bronco
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Ford Bronco. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ford Bronco diagnostics.
- ENGINE 42
- POWER TRAIN 34
- VISIBILITY/WIPER 64
- SERVICE BRAKES 41
- UNKNOWN OR OTHER 37
21 active recalls
- LATCHES/LOCKS/LINKAGES:DOORS:LOCK Jun 2022
Ford Motor Company (Ford) is recalling certain four-door 2021-2022 Bronco vehicles. The passenger-side rear door may be opened from inside of the vehicle when the child safety lock is in the "ON" position.…
NHTSA campaign 22V411000 - VISIBILITY:WINDSHIELD Jun 2022
Ford Motor Company (Ford) is recalling certain 2022 Bronco and Ranger vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle…
NHTSA campaign 22V451000 - BACK OVER PREVENTION: SENSING SYSTEM: CAMERA Nov 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requireme…
NHTSA campaign 22V825000 - AIR BAGS:SENSOR:SIDE IMPACT Dec 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The right or left side impact sensors may not be properly secured to the vehicle.…
NHTSA campaign 22V928000
How do I fix P0411 on a 2022 Ford Bronco?
- Replace the secondary air injection pump
- Replace the SAI combination / check valve
- Replace the SAI vacuum control solenoid
- Repair or replace cracked SAI hoses
- Clean carbon-clogged SAI passages in the exhaust manifold
About the 2020-2024 Ford Bronco
The 2020-2024 Ford Bronco was commonly sold with the following powertrains: 2.3L EcoBoost I4, 2.7L EcoBoost V6. Common trims include Base, Big Bend, Black Diamond, Outer Banks, Badlands, Wildtrak, Raptor.
Why P0411 is rare in the US fleet but common on European cars
US-market vehicles largely phased out secondary air injection in the 2010s as more efficient catalyst designs made it unnecessary. European-market vehicles continued using SAI well into the 2020s for tighter Euro 6 standards. As a result:
- VW, Audi, BMW, Porsche, Mercedes (2003-2018) — chronic SAI pump failures. The pump motor is often the most common failure point on these vehicles.
- US Domestic (Ford, GM, Chrysler 2005-2012) — used SAI on some platforms; eventually deleted.
- Most US vehicles 2015+ — no SAI system, so P0411 doesn’t apply.
If P0411 sets on a US-spec vehicle from the late 2010s or newer, double-check that the vehicle actually has an SAI system before diagnosing.
Carbon clogging in SAI passages
A common longer-term failure mode: SAI passages in the exhaust manifold accumulate carbon over years of use. Eventually airflow is restricted enough that even a working pump cannot deliver enough oxygen to the upstream O2 sensors during cold start. Cleaning the passages requires manifold removal — labor intensive. Some shops decline this repair and quote a full SAI delete (where legally permitted).
Drive cycle to verify a P0411 repair
P0411 only re-sets during cold-start enrichment. After any repair:
- Cold soak the engine 8+ hours
- Cold start and idle 2.5 minutes
- Drive a normal cycle, return home
- Repeat for 2-3 cold starts before assuming the fix held
A single warm-restart test cannot reproduce or rule out P0411.