P0335 on a 2022 Ram 1500
Crankshaft Position Sensor Circuit Fault
P0335 on a 2022 Ram 1500 indicates crankshaft position sensor circuit fault. Stop driving and diagnose it before continuing — it can signal an unsafe condition. The most common cause is failed crankshaft position sensor (heat-related failure) (typically $100–$400). Confirm the root cause before replacing parts.
What does P0335 mean on a 2022 Ram 1500?
P0335 is set when the engine control module does not receive a valid signal from the crankshaft position sensor. The crank sensor is the primary timing reference for the entire engine — fuel injection, ignition timing, and cam position correlation all depend on a clean crank signal. Without it, the engine will not start, or it will stall as soon as the signal drops out.
The symptoms, causes, and diagnostic steps below describe P0335 itself, so they read the same on nearby Ram 1500 model years. Powertrain and trim details vary year to year — confirm the specifics against your own vehicle before buying parts.
Is it safe to drive a 2022 Ram 1500 with P0335?
No. P0335 is a critical-severity code on the 2022 Ram 1500 — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.
What are the symptoms of P0335 on a 2022 Ram 1500?
- Check Engine Light is illuminated
- Engine cranks but will not start
- Intermittent stalling that worsens with engine heat
- Hard starting after a long drive (heat-soak failure)
- Sudden stalling at highway speed with restart difficulty
- Tachometer reads zero or fluctuates while running
- Hard cold start with extended crank time
What causes P0335 on a 2022 Ram 1500?
6 causes account for nearly all P0335 cases on a 2022 Ram 1500, ranked from most to least common. The most common, failed crankshaft position sensor (heat-related failure), typically runs $100–$400 at an independent U.S. shop.
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed crankshaft position sensor (heat-related failure) Heat-soak failure pattern is the textbook P0335 — fails when hot, recovers when cold. | Most common | $100–$400 |
| Damaged or melted sensor wiring near the exhaust | Common | $80–$350 |
| Corroded crank sensor connector | Common | $30–$200 |
| Damaged crank reluctor / tone ring (rare, requires teardown) | Rare | $1,500–$4,000 |
| Loose or improperly torqued sensor (cannot read gap correctly) | Occasional | $20–$100 |
| Failed PCM input (rare) | Rare | $400–$1,500 |
Cost ranges are editorial estimates for parts and labor at an independent U.S. shop — not quotes. What you actually pay moves with your region, the shop's hourly rate, which engine you have, and how much diagnostic time the job takes. Dealer service departments typically sit above these ranges.
How to diagnose this on a 2022 Ram 1500
-
Confirm the engine cranks but doesn't fire
P0335 typically presents as a crank-no-start. Confirm by cranking — the engine should rotate normally but never fire. If the engine fires intermittently, the sensor may be marginal; if it never fires, the sensor or wiring is fully out.
Tools: Common observation
-
Locate the sensor on the engine
Crank sensors are typically mounted on the timing cover (front of engine), the bell housing (rear of engine), or on the side of the block. Consult the service manual. Most are accessible from underneath with a basic socket set.
Tools: Vehicle-specific service information
-
Inspect wiring and connector
The sensor wiring routes close to the exhaust on many engines. Look for heat-damaged insulation, broken wires, or melted connectors. Sensor connectors near the firewall accumulate water and corrode — clean thoroughly.
Tools: Flashlight, Electrical contact cleaner
-
Test sensor resistance and reference voltage
Most crank sensors are inductive (variable reluctance) with approximately 200–2,000 Ω resistance, or Hall-effect with a 5 V reference. Compare to the service manual. With the connector unplugged and key on, verify the 5 V reference reaches the connector (Hall-effect sensors).
Tools: Multimeter, Wiring diagram
-
Heat-soak test for intermittent failures
P0335 that comes and goes with temperature is the textbook heat-soak failure pattern. Drive until the engine is hot, then attempt a restart immediately. If the engine cranks-no- starts hot and starts fine after cooling, the sensor is the cause even if cold-bench tests pass.
Tools: Patience
NHTSA complaints & recalls for the 2022 Ram 1500
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Ram 1500. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ram 1500 diagnostics.
NHTSA snapshot taken October 21, 2026; refreshed quarterly. For live figures see NHTSA.gov .
- ENGINE 248
- POWER TRAIN 103
- ELECTRICAL SYSTEM 197
- UNKNOWN OR OTHER 93
- FORWARD COLLISION AVOIDANCE 57
16 active recalls
- SEAT BELTS:REAR/OTHER:ANCHORAGE Jul 2026
Chrysler (FCA US, LLC) is recalling certain 2019-2026 Ram 1500 vehicles. The second-row center and left-side seat belt buckle anchors may have been improperly installed. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 2…
NHTSA campaign 26V495000 - AIR BAGS:FRONTAL Nov 2025
Chrysler (FCA US, LLC) is recalling certain 2021-2022 Ram 1500, Ram 2500, Ram 3500, Ram 4500, and Ram 5500 vehicles. The steering column control module may cause the driver's side air bag not to deploy as intended. As such, these vehicles fail to comply with the requirements of F…
NHTSA campaign 25V765000 - AIR BAGS May 2025
Chrysler (FCA US, LLC) is recalling certain 2019-2024 Ram 1500 vehicles. The driver's side air bag may not be connected properly, which can cause the air bag not to deploy as intended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety St…
NHTSA campaign 25V298000 - VISIBILITY:REARVIEW MIRRORS/DEVICES Oct 2024
Chrysler (FCA US, LLC) is recalling certain 2020-2023 Ram 1500 Classic vehicles equipped with heated trailer tow rearview mirrors. The mirror glass may detach from the driver's side heated trailer tow rearview mirror. As such these vehicles fail to comply with the requirements of…
NHTSA campaign 24V754000
How do I fix P0335 on a 2022 Ram 1500?
- Replace the crankshaft position sensor with an OEM part
- Repair damaged sensor wiring or connector
- Re-torque sensor to specification
- Replace damaged reluctor wheel (rare, major job)
Engines in the 2022 Ram 1500
The 2022 Ram 1500 was offered with the 3.0L 6-cylinder, 3.6L 6-cylinder, 5.7L 8-cylinder and 6.2L 8-cylinder engines. Which one you have changes where P0335 is most likely to originate, so confirm your engine before ordering parts.
Engine data: EPA fueleconomy.gov.
The “crank-no-start” pattern that distinguishes P0335 from no fuel / no spark
Three different no-start patterns:
- No spark, no fuel pulse — crank sensor (P0335). The engine cranks normally but the ECM never commands injectors or coils because it has no timing reference.
- Fuel but no spark — ignition system. Coils or coil drivers.
- Spark but no fuel — fuel system. Pump, relay, or wiring.
A scan tool can confirm P0335 by reading the crank RPM PID during cranking — it should report the cranking RPM (typically 150–300 RPM). If it reports zero or doesn’t update, the crank signal is the problem.
Heat-soak failure: the most frustrating intermittent
A failing crank sensor often works perfectly cold and fails after the engine reaches operating temperature. The pattern owners describe: drive for 30+ minutes, stop somewhere (gas station, errand), and the car will not restart for 15-30 minutes — then starts fine. This is the crank sensor failing under heat. A new sensor is the only fix.
Replace the sensor preemptively if you see this pattern; the failure mode worsens until the vehicle will not start at all.
Why P0335 is more serious than P0340 (cam sensor)
The cam sensor is supplementary on most engines — the ECM can run on the crank signal alone in a “limp” mode. The crank sensor is not supplementary; without it the ECM has no idea where any piston is, when to fire, or even whether the engine is running. P0335 = engine off until fixed. P0340 = engine runs poorly but runs.
P0335 on a 2022 Ram 1500: frequently asked questions
What does diagnostic trouble code P0335 mean on a 2022 Ram 1500?
P0335 is set when the engine control module does not receive a valid signal from the crankshaft position sensor. The crank sensor is the primary timing reference for the entire engine — fuel injection, ignition timing, and cam position correlation all depend on a clean crank signal. Without it, the engine will not start, or it will stall as soon as the signal drops out.
What are the symptoms of P0335 on a 2022 Ram 1500?
Check Engine Light is illuminated. Engine cranks but will not start. Intermittent stalling that worsens with engine heat. Hard starting after a long drive (heat-soak failure). Sudden stalling at highway speed with restart difficulty. Tachometer reads zero or fluctuates while running. Hard cold start with extended crank time
What causes P0335 on a 2022 Ram 1500?
Failed crankshaft position sensor (heat-related failure) (most-common, typically $100–$400 to repair). Damaged or melted sensor wiring near the exhaust (common, typically $80–$350 to repair). Corroded crank sensor connector (common, typically $30–$200 to repair). Damaged crank reluctor / tone ring (rare, requires teardown) (rare). Loose or improperly torqued sensor (cannot read gap correctly) (occasional). Failed PCM input (rare) (rare)
Is it safe to drive a 2022 Ram 1500 with P0335?
No. P0335 is a critical-severity code on the 2022 Ram 1500 — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.