P0335 on a 2012 Hyundai Tucson
Crankshaft Position Sensor Circuit Fault
P0335 on a 2012 Hyundai Tucson indicates crankshaft position sensor circuit fault. Stop driving and diagnose it before continuing — it can signal an unsafe condition. The most common cause is failed crankshaft position sensor (heat-related failure) (typically $100–$400). Confirm the root cause before replacing parts.
What does P0335 mean on a 2012 Hyundai Tucson?
P0335 is set when the engine control module does not receive a valid signal from the crankshaft position sensor. The crank sensor is the primary timing reference for the entire engine — fuel injection, ignition timing, and cam position correlation all depend on a clean crank signal. Without it, the engine will not start, or it will stall as soon as the signal drops out.
This guide covers P0335 across the 2010-2014 Hyundai Tucson generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Hyundai Tucson with P0335?
No. P0335 is a critical-severity code on the 2012 Hyundai Tucson — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.
What are the symptoms of P0335 on a 2012 Hyundai Tucson?
- Check Engine Light is illuminated
- Engine cranks but will not start
- Intermittent stalling that worsens with engine heat
- Hard starting after a long drive (heat-soak failure)
- Sudden stalling at highway speed with restart difficulty
- Tachometer reads zero or fluctuates while running
- Hard cold start with extended crank time
What causes P0335 on a 2012 Hyundai Tucson?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed crankshaft position sensor (heat-related failure) Heat-soak failure pattern is the textbook P0335 — fails when hot, recovers when cold. | Most common | $100–$400 |
| Damaged or melted sensor wiring near the exhaust | Common | $80–$350 |
| Corroded crank sensor connector | Common | $30–$200 |
| Damaged crank reluctor / tone ring (rare, requires teardown) | Rare | $1,500–$4,000 |
| Loose or improperly torqued sensor (cannot read gap correctly) | Occasional | $20–$100 |
| Failed PCM input (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2012 Hyundai Tucson
-
Confirm the engine cranks but doesn't fire
P0335 typically presents as a crank-no-start. Confirm by cranking — the engine should rotate normally but never fire. If the engine fires intermittently, the sensor may be marginal; if it never fires, the sensor or wiring is fully out.
Tools: Common observation
-
Locate the sensor on the engine
Crank sensors are typically mounted on the timing cover (front of engine), the bell housing (rear of engine), or on the side of the block. Consult the service manual. Most are accessible from underneath with a basic socket set.
Tools: Vehicle-specific service information
-
Inspect wiring and connector
The sensor wiring routes close to the exhaust on many engines. Look for heat-damaged insulation, broken wires, or melted connectors. Sensor connectors near the firewall accumulate water and corrode — clean thoroughly.
Tools: Flashlight, Electrical contact cleaner
-
Test sensor resistance and reference voltage
Most crank sensors are inductive (variable reluctance) with approximately 200–2,000 Ω resistance, or Hall-effect with a 5 V reference. Compare to the service manual. With the connector unplugged and key on, verify the 5 V reference reaches the connector (Hall-effect sensors).
Tools: Multimeter, Wiring diagram
-
Heat-soak test for intermittent failures
P0335 that comes and goes with temperature is the textbook heat-soak failure pattern. Drive until the engine is hot, then attempt a restart immediately. If the engine cranks-no- starts hot and starts fine after cooling, the sensor is the cause even if cold-bench tests pass.
Tools: Patience
NHTSA complaints & recalls for the 2012 Hyundai Tucson
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Hyundai Tucson. Use these to gauge how common a problem is on your specific vehicle before you start chasing Hyundai Tucson diagnostics.
- ENGINE 158
- POWER TRAIN 26
- SERVICE BRAKES 36
- HYDRAULIC 27
- ELECTRICAL SYSTEM 17
3 active recalls
- ENGINE AND ENGINE COOLING:ENGINE Feb 2019
Hyundai Motor America (Hyundai) is recalling certain 2011-2013 Tucson vehicles. The engine oil pan may leak and, if not addressed, the loss of oil may result in engine damage.…
NHTSA campaign 19V063000 - AIR BAGS May 2014
Hyundai Motor Company (Hyundai) is recalling certain model year 2011-2014 Hyundai Tucson vehicles manufactured January 3, 2011, through December 23, 2013. In the affected vehicles, the air bag assembly installed in the steering wheel may come loose from its mounting.…
NHTSA campaign 14V245000 - SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE Sep 2023
Hyundai Motor America (Hyundai) is recalling certain 2011-2015 Elantra, Genesis Coupe, Sonata Hybrid, 2012-2015 Accent, Azera, Veloster, 2013-2015 Elantra Coupe, Santa Fe, 2014-2015 Equus, 2010-2012 Veracruz, 2010-2013 Tucson, 2015 Tucson Fuel Cell, and 2013 Santa Fe Sport vehicl…
NHTSA campaign 23V651000
How do I fix P0335 on a 2012 Hyundai Tucson?
- Replace the crankshaft position sensor with an OEM part
- Repair damaged sensor wiring or connector
- Re-torque sensor to specification
- Replace damaged reluctor wheel (rare, major job)
About the 2010-2014 Hyundai Tucson
The 2010-2014 Hyundai Tucson was commonly sold with the following powertrains: 2.5L I4, 1.6L Turbo I4, 1.6L Hybrid I4, 1.6L Plug-in Hybrid I4. Common trims include SE, SEL, XRT, N Line, Limited.
The “crank-no-start” pattern that distinguishes P0335 from no fuel / no spark
Three different no-start patterns:
- No spark, no fuel pulse — crank sensor (P0335). The engine cranks normally but the ECM never commands injectors or coils because it has no timing reference.
- Fuel but no spark — ignition system. Coils or coil drivers.
- Spark but no fuel — fuel system. Pump, relay, or wiring.
A scan tool can confirm P0335 by reading the crank RPM PID during cranking — it should report the cranking RPM (typically 150–300 RPM). If it reports zero or doesn’t update, the crank signal is the problem.
Heat-soak failure: the most frustrating intermittent
A failing crank sensor often works perfectly cold and fails after the engine reaches operating temperature. The pattern owners describe: drive for 30+ minutes, stop somewhere (gas station, errand), and the car will not restart for 15-30 minutes — then starts fine. This is the crank sensor failing under heat. A new sensor is the only fix.
Replace the sensor preemptively if you see this pattern; the failure mode worsens until the vehicle will not start at all.
Why P0335 is more serious than P0340 (cam sensor)
The cam sensor is supplementary on most engines — the ECM can run on the crank signal alone in a “limp” mode. The crank sensor is not supplementary; without it the ECM has no idea where any piston is, when to fire, or even whether the engine is running. P0335 = engine off until fixed. P0340 = engine runs poorly but runs.
P0335 on a 2012 Hyundai Tucson: frequently asked questions
What does diagnostic trouble code P0335 mean on a 2012 Hyundai Tucson?
P0335 is set when the engine control module does not receive a valid signal from the crankshaft position sensor. The crank sensor is the primary timing reference for the entire engine — fuel injection, ignition timing, and cam position correlation all depend on a clean crank signal. Without it, the engine will not start, or it will stall as soon as the signal drops out.
What are the symptoms of P0335 on a 2012 Hyundai Tucson?
Check Engine Light is illuminated. Engine cranks but will not start. Intermittent stalling that worsens with engine heat. Hard starting after a long drive (heat-soak failure). Sudden stalling at highway speed with restart difficulty. Tachometer reads zero or fluctuates while running. Hard cold start with extended crank time
What causes P0335 on a 2012 Hyundai Tucson?
Failed crankshaft position sensor (heat-related failure) (most-common). Damaged or melted sensor wiring near the exhaust (common). Corroded crank sensor connector (common). Damaged crank reluctor / tone ring (rare, requires teardown) (rare). Loose or improperly torqued sensor (cannot read gap correctly) (occasional). Failed PCM input (rare) (rare)
Is it safe to drive a 2012 Hyundai Tucson with P0335?
No. P0335 is a critical-severity code on the 2012 Hyundai Tucson — avoid driving until it is diagnosed and repaired, as it can indicate an unsafe condition or risk further damage.