P0325 on a 2012 Honda Pilot
Knock Sensor 1 Circuit Fault
P0325 on a 2012 Honda Pilot indicates knock sensor 1 circuit fault. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed knock sensor element (typically $150–$600). Confirm the root cause before replacing parts.
What does P0325 mean on a 2012 Honda Pilot?
P0325 is set when the engine control module does not receive a valid signal from the Bank 1 knock sensor — or the only knock sensor on engines that use one. The knock sensor is a piezoelectric vibration sensor that listens for the characteristic frequency of pre-ignition (detonation) so the ECM can pull timing to protect the engine. With no usable knock signal, the ECM defaults to conservative timing maps, which reduces power and fuel economy.
This guide covers P0325 across the 2010-2014 Honda Pilot generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Honda Pilot with P0325?
In most cases a 2012 Honda Pilot stays drivable for short trips with P0325 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0325 on a 2012 Honda Pilot?
- Check Engine Light is illuminated
- Reduced power and slower throttle response
- Slight reduction in fuel economy
- Engine may run cooler than normal under load
- Possible audible engine ping or knock under hard acceleration
- No drivability issue in normal driving
What causes P0325 on a 2012 Honda Pilot?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed knock sensor element Most common at 100k+ miles. Some engines bury the sensor under the intake. | Most common | $150–$600 |
| Damaged or corroded knock sensor wiring or connector | Common | $80–$350 |
| Loose knock sensor mounting (sensor must be torqued correctly to "hear") | Common | $20–$100 |
| Rodent damage to knock sensor harness (parked vehicles) | Occasional | $80–$350 |
| Failed knock sensor sub-harness on GM L83/L86 truck V8s Specific to GM 5.3 / 6.2 truck V8s — well-documented sub-harness failure. | Occasional | $200–$600 |
| Internal engine damage producing noise outside the knock sensor band | Rare | $2,000–$6,000 |
How to diagnose this on a 2012 Honda Pilot
-
Locate the knock sensor — often under the intake manifold
On many engines (notably GM V6 + V8 truck engines, Toyota 2GR-FE, and most modern Hondas) the knock sensor sits in the engine valley under the intake manifold. Knowing this before starting saves a wasted hour of looking. Consult the service manual.
Tools: Vehicle-specific service information
-
Test knock sensor resistance
Unplug the sensor and measure resistance with a multimeter. Most knock sensors read approximately 90 kΩ to 2.5 MΩ depending on style. Infinite resistance (open) or near-zero (short) confirms a failed sensor.
Tools: Multimeter, Service spec sheet
-
Inspect the wiring and connector
Knock sensor harnesses run close to hot exhaust components and are common chafing victims. Inspect every inch of the harness from the sensor to the PCM connector. Repair any visible damage before replacing the sensor.
Tools: Inspection mirror, Flashlight, Wire repair supplies
-
Verify torque specification on the existing sensor
A knock sensor mounted with the wrong torque cannot transmit vibration efficiently. Spec is typically 15–25 ft-lb. Use a torque wrench, not "tight by feel." Over-torque can crack the housing; under-torque produces false knock-sensor codes.
Tools: Torque wrench, Service spec sheet
-
Check for GM-specific sub-harness failure
On GM L83 (5.3 V8) and L86 (6.2 V8) truck engines, the knock sensor sub-harness running under the intake manifold is a documented failure point — the harness chafes and shorts. Replacement requires intake manifold removal. The sub-harness itself is inexpensive but the labor is significant.
Tools: Intake manifold gasket, Common hand tools
NHTSA complaints & recalls for the 2012 Honda Pilot
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Honda Pilot. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda Pilot diagnostics.
- ENGINE 35
- POWER TRAIN 20
- VEHICLE SPEED CONTROL 17
- SERVICE BRAKES 28
- ELECTRICAL SYSTEM 22
9 active recalls
- AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Sep 2018
Honda (American Honda Motor Co.) is recalling certain 2014 Honda Insight and Acura TSX and TSX Wagon, 2014-2015 Honda Crosstour and Pilot vehicles nationwide, as well as certain 2014 Honda FCX Clarity and Fit EV vehicles in Florida, Hawaii, Puerto Rico, Texas, Alabama, Georgia, L…
NHTSA campaign 18V661000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Apr 2018
Honda (American Honda Motor Co.) is recalling certain 2003-2012 Honda Accord and Pilot, 2010 Accord Crosstour, 2001-2011 Civic, 2002-2011 CR-V, 2003-2004, 2006-2008 and 2011 Element, 2007 and 2009-2013 Fit, 2010-2012 Insight, 2002-2004 Odyssey, and 2012 Ridgeline vehicles. The f…
NHTSA campaign 18V268000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Jun 2019
Honda (American Honda Motor Co.) is recalling certain 2009-2014 Acura TSX, 2011-2014 TSX Sport Wagon, 2010-2013 ZDX, 2008-2012 Honda Accord, 2010-2011 Accord Crosstour, 2006-2011 Civic and Civic Hybrid, 2008-2010 Civic GX NGV, 2012-2015 Crosstour, 2007-2011 CR-V, 2009-2013 Fit, 2…
NHTSA campaign 19V502000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE May 2019
Honda (American Honda Motor Co.) is recalling certain 2009-2014 Acura TSX, 2011-2013 TSX Sport Wagon, and 2010-2012 ZDX and 2008-2012 Honda Accord, 2010-2011 Accord Crosstour, 2006-2011 Civic, Civic Hybrid and Civic NGV, 2012-2014 Crosstour, 2007-2011 CR-V, 2009-2013 Fit, 2010-20…
NHTSA campaign 19V378000
How do I fix P0325 on a 2012 Honda Pilot?
- Replace the knock sensor with an OEM part
- Replace the knock sensor sub-harness (GM L83/L86)
- Repair damaged wiring to the knock sensor
- Re-torque the sensor to OEM specification
About the 2010-2014 Honda Pilot
The 2010-2014 Honda Pilot was commonly sold with the following powertrains: 3.5L V6. Common trims include LX, EX, EX-L, Touring, Elite, TrailSport.
Why P0325 is a “common” code on GM V8 trucks
GM L83 (5.3L) and L86 (6.2L) Gen V V8 engines — used in 2014+ Silverado, Sierra, Tahoe, Yukon, Suburban, and Escalade — have a well-documented knock sensor sub-harness failure. The harness chafes against the intake valley pan and eventually shorts. P0325 + P0330 setting together on these engines is so common that aftermarket “extended” sub-harnesses are sold specifically to relocate the wiring away from the chafe point.
If you have one of these vehicles, expect this repair around 80–130k miles. Plan it with the next intake manifold service.
What the ECM does without a working knock sensor
The engine still runs — but conservatively. The ECM uses “open-loop” ignition timing maps that pull 3–6 degrees of advance out of every cell, sacrificing power and fuel economy to ensure no detonation. Expect 1–2 MPG lower and noticeably slower throttle response.
Knock sensor diagnostics with a scope
The knock sensor is essentially a microphone. Tapping the cylinder block near the sensor with a screwdriver while watching the scan-tool knock count PID should produce hits. No response to tapping confirms a dead sensor or open wiring even if the multimeter resistance looks correct.
P0325 on a 2012 Honda Pilot: frequently asked questions
What does diagnostic trouble code P0325 mean on a 2012 Honda Pilot?
P0325 is set when the engine control module does not receive a valid signal from the Bank 1 knock sensor — or the only knock sensor on engines that use one. The knock sensor is a piezoelectric vibration sensor that listens for the characteristic frequency of pre-ignition (detonation) so the ECM can pull timing to protect the engine. With no usable knock signal, the ECM defaults to conservative timing maps, which reduces power and fuel economy.
What are the symptoms of P0325 on a 2012 Honda Pilot?
Check Engine Light is illuminated. Reduced power and slower throttle response. Slight reduction in fuel economy. Engine may run cooler than normal under load. Possible audible engine ping or knock under hard acceleration. No drivability issue in normal driving
What causes P0325 on a 2012 Honda Pilot?
Failed knock sensor element (most-common). Damaged or corroded knock sensor wiring or connector (common). Loose knock sensor mounting (sensor must be torqued correctly to "hear") (common). Rodent damage to knock sensor harness (parked vehicles) (occasional). Failed knock sensor sub-harness on GM L83/L86 truck V8s (occasional). Internal engine damage producing noise outside the knock sensor band (rare)
Is it safe to drive a 2012 Honda Pilot with P0325?
In most cases a 2012 Honda Pilot stays drivable for short trips with P0325 active, but it should be diagnosed and repaired promptly — this is a moderate-severity code. Ignoring it can lead to further damage or a failed emissions test.