P0133 on a 2022 Subaru Forester
O2 Sensor Slow Response (Bank 1 Upstream)
P0133 on a 2022 Subaru Forester indicates o2 sensor slow response (bank 1 upstream). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is aged or contaminated bank 1 upstream o2 sensor (typically $150–$450). Confirm the root cause before replacing parts.
What does P0133 mean on a 2022 Subaru Forester?
P0133 is set when the upstream oxygen sensor on Bank 1 takes longer than the calibrated maximum to switch between rich and lean readings during normal closed-loop operation. A healthy upstream O2 sensor switches several times per second at 2500 RPM. A "lazy" sensor switches slowly, which prevents the ECM from making fast fuel adjustments — degrading drivability and emissions.
This guide covers P0133 across the 2020-2024 Subaru Forester generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Subaru Forester with P0133?
In most cases a 2022 Subaru Forester stays drivable for short trips with P0133 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0133 on a 2022 Subaru Forester?
- Check Engine Light is illuminated
- Slight reduction in fuel economy
- Mild hesitation or surging at steady cruise
- Possible eventual P0420 (catalyst code) as the slow O2 fools the cat monitor
- Rough running rare unless other codes also present
What causes P0133 on a 2022 Subaru Forester?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Aged or contaminated Bank 1 upstream O2 sensor Most common after 80–120k miles or after silicone-contamination events. | Most common | $150–$450 |
| Silicone contamination from RTV sealant or anti-freeze leak Silicone glazes the sensor element and slows it permanently. | Common | $150–$600 |
| Lead-poisoned sensor (rare — leaded fuel exposure) | Rare | $150–$450 |
| Failing sensor heater extending warm-up time | Occasional | $150–$450 |
| Exhaust leak upstream causing the sensor to read inconsistently | Occasional | $100–$500 |
| Aftermarket O2 sensor with wrong response curve | Occasional | $150–$450 |
How to diagnose this on a 2022 Subaru Forester
-
Graph the upstream O2 sensor signal
With the engine fully warm and held at 2500 RPM, graph the Bank 1 upstream O2 voltage. A healthy sensor switches between approximately 0.1 V and 0.9 V at least 5 times in 10 seconds. A slow sensor switches 2–3 times — or worse, fewer. Compare to the Bank 2 sensor (if equipped) to confirm one is slow.
Tools: Scan tool with O2 voltage graphing
-
Check for exhaust leaks ahead of the sensor
Cold-start the engine and listen along the exhaust manifold and gaskets. A small upstream leak admits fresh air that causes the sensor to read inconsistently and lazily.
Tools: Mechanic's stethoscope, Flashlight
-
Inspect the sensor for contamination
Remove the sensor and visually inspect the tip: - Black soot — rich-running condition (fix the underlying cause first) - White or chalky coating — silicone contamination (sensor is finished) - Brown or oily film — oil consumption issue (engine work needed) - Green — coolant in the exhaust (head gasket or intake leak) Contamination is permanent for the sensor — replace it AND fix the underlying cause.
Tools: Oxygen sensor socket, Anti-seize compound (for reinstall)
-
Test heater current
A heater with reduced current draws keeps the sensor cool, which slows its response. Measure heater current — typical 0.8 to 2 A. Below 0.5 A is "weak" heater that does not warm fast enough.
Tools: Multimeter with current function
-
Confirm sensor is OEM spec on previously-replaced units
Aftermarket O2 sensors at half the OEM price often have a slower response curve that sets P0133 even when "working." Confirm the installed sensor is the correct part number for this vehicle's year, make, model, engine, and emissions package (federal vs. California).
Tools: Sensor part number verification
NHTSA complaints & recalls for the 2022 Subaru Forester
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Subaru Forester. Use these to gauge how common a problem is on your specific vehicle before you start chasing Subaru Forester diagnostics.
- ENGINE 10
- VEHICLE SPEED CONTROL 9
- VISIBILITY/WIPER 20
- UNKNOWN OR OTHER 17
- FORWARD COLLISION AVOIDANCE 12
1 active recall
- POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START INTERLOCK SWITCH Nov 2023
Subaru of America, Inc. is recalling certain model year 2021 Crosstrek, 2022 Forester, 2021-2023 Legacy, and Outback vehicles. An insufficient weld may allow water to enter the inhibitor switch, causing it to fail.…
NHTSA campaign 23V755000
How do I fix P0133 on a 2022 Subaru Forester?
- Replace the Bank 1 upstream O2 sensor with an OEM part (Bosch / NTK / Denso)
- Repair exhaust leaks upstream of the sensor
- Address silicone or coolant contamination source before replacing the sensor
- Replace if heater current is below spec
About the 2020-2024 Subaru Forester
The 2020-2024 Subaru Forester was commonly sold with the following powertrains: 2.5L H4, 2.0L Turbo H4. Common trims include Base, Premium, Sport, Limited, Touring, Wilderness.
Why P0133 leads to P0420
A lazy upstream O2 sensor confuses the catalyst monitor. The downstream sensor sees what the upstream sensor reports plus a delay through the catalyst. If the upstream sensor itself is delayed, the downstream readings look “too similar” to upstream — and the ECM concludes the catalyst is dead. A P0133 left unresolved for months often produces a P0420 that was never the catalyst’s fault.
RTV / silicone gasket damage
P0133 occurring shortly after engine work — particularly intake manifold, valve cover, or oil pan replacement — is often caused by silicone vapor from un-cured RTV sealant. The vapor coats the O2 sensor element and slows it permanently. The fix is the sensor; the prevention is using “sensor safe” RTV (always check the label) and letting the sealant fully cure before starting the engine.
OEM vs. aftermarket O2 sensors
P0133 specifically is sensitive to the response curve of the sensor — and cheap aftermarket sensors often have slower curves even when they are otherwise functional. A $30 generic O2 might work for years on a 1995 vehicle but will set P0133 on a 2018 vehicle whose ECM expects faster switching. Buy NTK, Denso, or Bosch sensors of the exact part number called out for the vehicle.