P0133 on a 2017 Chevrolet Trax
O2 Sensor Slow Response (Bank 1 Upstream)
P0133 on a 2017 Chevrolet Trax indicates o2 sensor slow response (bank 1 upstream). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is aged or contaminated bank 1 upstream o2 sensor (typically $150–$450). Confirm the root cause before replacing parts.
What does P0133 mean on a 2017 Chevrolet Trax?
P0133 is set when the upstream oxygen sensor on Bank 1 takes longer than the calibrated maximum to switch between rich and lean readings during normal closed-loop operation. A healthy upstream O2 sensor switches several times per second at 2500 RPM. A "lazy" sensor switches slowly, which prevents the ECM from making fast fuel adjustments — degrading drivability and emissions.
This guide covers P0133 across the 2015-2019 Chevrolet Trax generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Chevrolet Trax with P0133?
In most cases a 2017 Chevrolet Trax stays drivable for short trips with P0133 active, but diagnose and repair it promptly. This is a moderate-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0133 on a 2017 Chevrolet Trax?
- Check Engine Light is illuminated
- Slight reduction in fuel economy
- Mild hesitation or surging at steady cruise
- Possible eventual P0420 (catalyst code) as the slow O2 fools the cat monitor
- Rough running rare unless other codes also present
What causes P0133 on a 2017 Chevrolet Trax?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Aged or contaminated Bank 1 upstream O2 sensor Most common after 80–120k miles or after silicone-contamination events. | Most common | $150–$450 |
| Silicone contamination from RTV sealant or anti-freeze leak Silicone glazes the sensor element and slows it permanently. | Common | $150–$600 |
| Lead-poisoned sensor (rare — leaded fuel exposure) | Rare | $150–$450 |
| Failing sensor heater extending warm-up time | Occasional | $150–$450 |
| Exhaust leak upstream causing the sensor to read inconsistently | Occasional | $100–$500 |
| Aftermarket O2 sensor with wrong response curve | Occasional | $150–$450 |
How to diagnose this on a 2017 Chevrolet Trax
-
Graph the upstream O2 sensor signal
With the engine fully warm and held at 2500 RPM, graph the Bank 1 upstream O2 voltage. A healthy sensor switches between approximately 0.1 V and 0.9 V at least 5 times in 10 seconds. A slow sensor switches 2–3 times — or worse, fewer. Compare to the Bank 2 sensor (if equipped) to confirm one is slow.
Tools: Scan tool with O2 voltage graphing
-
Check for exhaust leaks ahead of the sensor
Cold-start the engine and listen along the exhaust manifold and gaskets. A small upstream leak admits fresh air that causes the sensor to read inconsistently and lazily.
Tools: Mechanic's stethoscope, Flashlight
-
Inspect the sensor for contamination
Remove the sensor and visually inspect the tip: - Black soot — rich-running condition (fix the underlying cause first) - White or chalky coating — silicone contamination (sensor is finished) - Brown or oily film — oil consumption issue (engine work needed) - Green — coolant in the exhaust (head gasket or intake leak) Contamination is permanent for the sensor — replace it AND fix the underlying cause.
Tools: Oxygen sensor socket, Anti-seize compound (for reinstall)
-
Test heater current
A heater with reduced current draws keeps the sensor cool, which slows its response. Measure heater current — typical 0.8 to 2 A. Below 0.5 A is "weak" heater that does not warm fast enough.
Tools: Multimeter with current function
-
Confirm sensor is OEM spec on previously-replaced units
Aftermarket O2 sensors at half the OEM price often have a slower response curve that sets P0133 even when "working." Confirm the installed sensor is the correct part number for this vehicle's year, make, model, engine, and emissions package (federal vs. California).
Tools: Sensor part number verification
NHTSA complaints & recalls for the 2017 Chevrolet Trax
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Chevrolet Trax. Use these to gauge how common a problem is on your specific vehicle before you start chasing Chevrolet Trax diagnostics.
- ENGINE 40
- ELECTRICAL SYSTEM 24
- UNKNOWN OR OTHER 22
- STEERING 19
- SUSPENSION 10
3 active recalls
- SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT Apr 2019
General Motors LLC (GM) is recalling certain 2017-2019 Chevrolet Trax vehicles. A joint in one or both of the front lower-control arms may have been improperly welded. An improperly welded joint may break, resulting in the partial separation of the lower-control arm from the ve…
NHTSA campaign 19V312000 - SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT Sep 2019
General Motors LLC (GM) is recalling certain 2015-2018 Chevrolet Trax vehicles. A joint in one or both of the front lower control arms may have been improperly welded. An improperly welded joint may break, resulting in the partial separation of the lower control arm from the vehi…
NHTSA campaign 19V652000 - AIR BAGS:FRONTAL Sep 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500…
NHTSA campaign 16V651000
How do I fix P0133 on a 2017 Chevrolet Trax?
- Replace the Bank 1 upstream O2 sensor with an OEM part (Bosch / NTK / Denso)
- Repair exhaust leaks upstream of the sensor
- Address silicone or coolant contamination source before replacing the sensor
- Replace if heater current is below spec
About the 2015-2019 Chevrolet Trax
The 2015-2019 Chevrolet Trax was commonly sold with the following powertrains: 1.4L Turbo I4, 1.2L Turbo I3. Common trims include LS, 1RS, LT, 2RS, Activ.
Why P0133 leads to P0420
A lazy upstream O2 sensor confuses the catalyst monitor. The downstream sensor sees what the upstream sensor reports plus a delay through the catalyst. If the upstream sensor itself is delayed, the downstream readings look “too similar” to upstream — and the ECM concludes the catalyst is dead. A P0133 left unresolved for months often produces a P0420 that was never the catalyst’s fault.
RTV / silicone gasket damage
P0133 occurring shortly after engine work — particularly intake manifold, valve cover, or oil pan replacement — is often caused by silicone vapor from un-cured RTV sealant. The vapor coats the O2 sensor element and slows it permanently. The fix is the sensor; the prevention is using “sensor safe” RTV (always check the label) and letting the sealant fully cure before starting the engine.
OEM vs. aftermarket O2 sensors
P0133 specifically is sensitive to the response curve of the sensor — and cheap aftermarket sensors often have slower curves even when they are otherwise functional. A $30 generic O2 might work for years on a 1995 vehicle but will set P0133 on a 2018 vehicle whose ECM expects faster switching. Buy NTK, Denso, or Bosch sensors of the exact part number called out for the vehicle.
P0133 on a 2017 Chevrolet Trax: frequently asked questions
What does diagnostic trouble code P0133 mean on a 2017 Chevrolet Trax?
P0133 is set when the upstream oxygen sensor on Bank 1 takes longer than the calibrated maximum to switch between rich and lean readings during normal closed-loop operation. A healthy upstream O2 sensor switches several times per second at 2500 RPM. A "lazy" sensor switches slowly, which prevents the ECM from making fast fuel adjustments — degrading drivability and emissions.
What are the symptoms of P0133 on a 2017 Chevrolet Trax?
Check Engine Light is illuminated. Slight reduction in fuel economy. Mild hesitation or surging at steady cruise. Possible eventual P0420 (catalyst code) as the slow O2 fools the cat monitor. Rough running rare unless other codes also present
What causes P0133 on a 2017 Chevrolet Trax?
Aged or contaminated Bank 1 upstream O2 sensor (most-common). Silicone contamination from RTV sealant or anti-freeze leak (common). Lead-poisoned sensor (rare — leaded fuel exposure) (rare). Failing sensor heater extending warm-up time (occasional). Exhaust leak upstream causing the sensor to read inconsistently (occasional). Aftermarket O2 sensor with wrong response curve (occasional)
Is it safe to drive a 2017 Chevrolet Trax with P0133?
In most cases a 2017 Chevrolet Trax stays drivable for short trips with P0133 active, but it should be diagnosed and repaired promptly — this is a moderate-severity code. Ignoring it can lead to further damage or a failed emissions test.