P0113 on a 2022 Hyundai Santa Fe
Intake Air Temperature High Input
P0113 on a 2022 Hyundai Santa Fe indicates intake air temperature high input. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is disconnected or unlatched iat / maf-iat connector (typically $0–$50). Confirm the root cause before replacing parts.
What does P0113 mean on a 2022 Hyundai Santa Fe?
P0113 is set when the ECM sees the intake air temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold air temperature (often below −40 °F / −40 °C). This is the textbook fingerprint of an open circuit at the IAT sensor: a disconnected sensor, a broken signal wire, or a failed sensor element.
This guide covers P0113 across the 2020-2024 Hyundai Santa Fe generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Hyundai Santa Fe with P0113?
In most cases a 2022 Hyundai Santa Fe stays drivable for short trips with P0113 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0113 on a 2022 Hyundai Santa Fe?
- Check Engine Light is illuminated
- Slightly harder cold starting in some cases
- Mild reduction in fuel economy
- Reduced power under hard acceleration (engine adds extra fuel for "cold" air)
- Often no noticeable drivability problem at all
What causes P0113 on a 2022 Hyundai Santa Fe?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Disconnected or unlatched IAT / MAF-IAT connector | Most common | $0–$50 |
| Open circuit in the IAT signal wire (broken, chafed, or pinched) | Common | $80–$350 |
| Failed IAT sensor element (open internally) | Common | $30–$150 |
| Corroded sensor connector pins | Common | $30–$200 |
| Damaged sensor body from intake backfire | Occasional | $30–$200 |
| Failed PCM input (extremely rare) | Rare | $400–$1,500 |
How to diagnose this on a 2022 Hyundai Santa Fe
-
Confirm where the IAT sensor lives on this engine
Modern engines fall into two configurations: a standalone IAT sensor in the air intake tract, or a combined MAF/IAT assembly where the IAT element is built into the mass airflow housing. Both share P0113 — the diagnostic difference is where to find the connector and which wires carry the IAT signal.
Tools: Vehicle-specific service information
-
Read IAT temperature on the scan tool
A working IAT reads close to ambient air temperature when the engine has been off long enough to cool. Compare to the coolant temperature reading at cold start — they should agree within a few degrees. An IAT reading of "−40 °F" or "−40 °C" is the classic open-circuit fingerprint.
Tools: Scan tool with IAT PID
-
Inspect the connector and wiring
Unplug the IAT connector and inspect for corrosion, water, or bent pins. With the connector unplugged and the key on, the scan tool should still report a fixed "very cold" value — that confirms an open circuit signature is what set the code.
Tools: Electrical contact cleaner, Flashlight
-
Bench-test the IAT sensor with a multimeter
With the sensor removed, measure resistance across its terminals at room temperature. Compare to the service manual — most NTC IAT sensors read 2.0–4.5 kΩ at 68 °F (20 °C). Infinite resistance means the sensor is open and dead. Heating the sensor gently should cause resistance to drop.
Tools: Multimeter, Heat gun or hair dryer (optional), Service spec sheet
-
Jumper test the signal wire
With the IAT disconnected, briefly jumper the signal wire to ground and observe the scan tool reading — it should swing from "very cold" to "very hot" (P0112 territory). If the reading does not change, the wiring or PCM input is at fault rather than the sensor.
Tools: Jumper wire, Scan tool
NHTSA complaints & recalls for the 2022 Hyundai Santa Fe
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Hyundai Santa Fe. Use these to gauge how common a problem is on your specific vehicle before you start chasing Hyundai Santa Fe diagnostics.
- POWER TRAIN 52
- ENGINE 49
- VEHICLE SPEED CONTROL 15
- UNKNOWN OR OTHER 41
- ELECTRICAL SYSTEM 25
5 active recalls
- FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS Jul 2021
Hyundai Motor America (Hyundai) is recalling certain 2021-2022 Santa Fe and Sonata vehicles equipped with 2.5L turbocharged engines. Fuel may leak at the pipe connection between the high-pressure fuel pump and fuel rail.…
NHTSA campaign 21V524000 - ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER Mar 2022
Hyundai Motor America (Hyundai) is recalling certain 2022 Santa Fe and Santa Cruz vehicles. The oil supply pipe to the turbocharger may crack, which could result in an oil leak in the engine compartment.…
NHTSA campaign 22V197000 - POWER TRAIN:AUTOMATIC TRANSMISSION Oct 2022
Hyundai Motor Company (Hyundai) is recalling certain 2021-2022 Santa Fe, Sonata, Veloster N, 2022 Santa Cruz, Elantra N, and Kona N vehicles. The vehicle's "fail-safe" limited-mobility drive mode may be impaired, when prompted by a transmission oil pump malfunction, which can re…
NHTSA campaign 22V746000 - TRAILER HITCHES Mar 2023
Hyundai Motor America (Hyundai) is recalling certain 2019-2023 Santa Fe, 2021-2023 Santa Fe HEV, 2022-2023 Santa Fe Plug-in HEV and Santa Cruz vehicles potentially equipped with a tow hitch harness installed as original equipment, or purchased as an accessory through a Hyundai de…
NHTSA campaign 23V181000
How do I fix P0113 on a 2022 Hyundai Santa Fe?
- Reconnect the IAT or MAF-IAT connector
- Replace the IAT sensor (standalone) or the MAF/IAT assembly
- Repair broken IAT signal wire
- Clean corroded sensor connector pins
About the 2020-2024 Hyundai Santa Fe
The 2020-2024 Hyundai Santa Fe was commonly sold with the following powertrains: 2.5L I4, 2.5L Turbo I4, 1.6L Hybrid I4. Common trims include SE, SEL, XRT, Limited, Calligraphy.
P0113 vs P0112
These are the two ends of the same circuit:
- P0112 — IAT signal reads too low (sensor sees a very high temperature, often “300 °F”). Usually a shorted-to-ground signal wire or a sensor failed in the closed direction.
- P0113 — IAT signal reads too high (sensor sees a very low temperature, often “−40 °F”). Usually an open circuit — disconnected, broken wire, or sensor open internally.
Why P0113 rarely affects drivability
Modern ECMs use the IAT for relatively minor fuel-trim corrections and to fine-tune cold-start enrichment. With a missing IAT signal, the ECM uses a default value (usually around 70 °F) and the engine runs essentially normally. This is why many drivers report P0113 with no symptoms at all beyond the Check Engine Light.
Combined MAF/IAT assemblies
On most modern vehicles the IAT is integrated into the MAF housing as a single assembly. When the IAT element fails, the entire MAF assembly must be replaced — there is no separate IAT to service. Confirm the part number before ordering; combined assemblies are 4–10× the cost of a standalone IAT.