P0113 on a 2017 Toyota Sienna
Intake Air Temperature High Input
P0113 on a 2017 Toyota Sienna indicates intake air temperature high input. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is disconnected or unlatched iat / maf-iat connector (typically $0–$50). Confirm the root cause before replacing parts.
What does P0113 mean on a 2017 Toyota Sienna?
P0113 is set when the ECM sees the intake air temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold air temperature (often below −40 °F / −40 °C). This is the textbook fingerprint of an open circuit at the IAT sensor: a disconnected sensor, a broken signal wire, or a failed sensor element.
This guide covers P0113 across the 2015-2019 Toyota Sienna generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Toyota Sienna with P0113?
In most cases a 2017 Toyota Sienna stays drivable for short trips with P0113 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0113 on a 2017 Toyota Sienna?
- Check Engine Light is illuminated
- Slightly harder cold starting in some cases
- Mild reduction in fuel economy
- Reduced power under hard acceleration (engine adds extra fuel for "cold" air)
- Often no noticeable drivability problem at all
What causes P0113 on a 2017 Toyota Sienna?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Disconnected or unlatched IAT / MAF-IAT connector | Most common | $0–$50 |
| Open circuit in the IAT signal wire (broken, chafed, or pinched) | Common | $80–$350 |
| Failed IAT sensor element (open internally) | Common | $30–$150 |
| Corroded sensor connector pins | Common | $30–$200 |
| Damaged sensor body from intake backfire | Occasional | $30–$200 |
| Failed PCM input (extremely rare) | Rare | $400–$1,500 |
How to diagnose this on a 2017 Toyota Sienna
-
Confirm where the IAT sensor lives on this engine
Modern engines fall into two configurations: a standalone IAT sensor in the air intake tract, or a combined MAF/IAT assembly where the IAT element is built into the mass airflow housing. Both share P0113 — the diagnostic difference is where to find the connector and which wires carry the IAT signal.
Tools: Vehicle-specific service information
-
Read IAT temperature on the scan tool
A working IAT reads close to ambient air temperature when the engine has been off long enough to cool. Compare to the coolant temperature reading at cold start — they should agree within a few degrees. An IAT reading of "−40 °F" or "−40 °C" is the classic open-circuit fingerprint.
Tools: Scan tool with IAT PID
-
Inspect the connector and wiring
Unplug the IAT connector and inspect for corrosion, water, or bent pins. With the connector unplugged and the key on, the scan tool should still report a fixed "very cold" value — that confirms an open circuit signature is what set the code.
Tools: Electrical contact cleaner, Flashlight
-
Bench-test the IAT sensor with a multimeter
With the sensor removed, measure resistance across its terminals at room temperature. Compare to the service manual — most NTC IAT sensors read 2.0–4.5 kΩ at 68 °F (20 °C). Infinite resistance means the sensor is open and dead. Heating the sensor gently should cause resistance to drop.
Tools: Multimeter, Heat gun or hair dryer (optional), Service spec sheet
-
Jumper test the signal wire
With the IAT disconnected, briefly jumper the signal wire to ground and observe the scan tool reading — it should swing from "very cold" to "very hot" (P0112 territory). If the reading does not change, the wiring or PCM input is at fault rather than the sensor.
Tools: Jumper wire, Scan tool
NHTSA complaints & recalls for the 2017 Toyota Sienna
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Toyota Sienna. Use these to gauge how common a problem is on your specific vehicle before you start chasing Toyota Sienna diagnostics.
- POWER TRAIN 33
- ENGINE 15
- UNKNOWN OR OTHER 25
- ELECTRICAL SYSTEM 19
- WHEELS 16
10 active recalls
- STEERING Jul 2019
Braun Corporation (Braun) is recalling certain modified 2017-2020 Toyota Sienna vehicles. The steering shaft extensions may have been improperly manufactured, possibly causing the extensions to fracture.…
NHTSA campaign 19V532000 - SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS Jun 2019
Braun Corporation (Braun) is recalling certain 2014-2019 Toyota Sienna mobility van conversions. The brake lines may have incorrect tube nut fittings installed, which may cause a pressure drop within the braking system.…
NHTSA campaign 19V410000 - EQUIPMENT:OTHER:LABELS Jun 2019
Southeast Toyota Distributors, LLC (SET) is recalling certain 2017-2019 Toyota Camry, Corolla, Rav4, Sienna, and Yaris iA vehicles equipped with factory-installed floor mats. The load carrying capacity modification label may be incorrect. As such, these vehicles fail to comply…
NHTSA campaign 19V503000 - SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS Jul 2019
Vantage Mobility International, LLC (Vantage) is recalling certain 2012-2018 AMS Genesis wheelchair vans, built on a Toyota Sienna vehicles. The rubber brake hoses that attach to the rear wheel assembly may be too short, causing them to rub against the rear axle trailing arm.…
NHTSA campaign 19V553000
How do I fix P0113 on a 2017 Toyota Sienna?
- Reconnect the IAT or MAF-IAT connector
- Replace the IAT sensor (standalone) or the MAF/IAT assembly
- Repair broken IAT signal wire
- Clean corroded sensor connector pins
About the 2015-2019 Toyota Sienna
The 2015-2019 Toyota Sienna was commonly sold with the following powertrains: 3.5L V6, 2.5L Hybrid I4. Common trims include LE, XLE, XSE, Limited, Platinum.
P0113 vs P0112
These are the two ends of the same circuit:
- P0112 — IAT signal reads too low (sensor sees a very high temperature, often “300 °F”). Usually a shorted-to-ground signal wire or a sensor failed in the closed direction.
- P0113 — IAT signal reads too high (sensor sees a very low temperature, often “−40 °F”). Usually an open circuit — disconnected, broken wire, or sensor open internally.
Why P0113 rarely affects drivability
Modern ECMs use the IAT for relatively minor fuel-trim corrections and to fine-tune cold-start enrichment. With a missing IAT signal, the ECM uses a default value (usually around 70 °F) and the engine runs essentially normally. This is why many drivers report P0113 with no symptoms at all beyond the Check Engine Light.
Combined MAF/IAT assemblies
On most modern vehicles the IAT is integrated into the MAF housing as a single assembly. When the IAT element fails, the entire MAF assembly must be replaced — there is no separate IAT to service. Confirm the part number before ordering; combined assemblies are 4–10× the cost of a standalone IAT.
P0113 on a 2017 Toyota Sienna: frequently asked questions
What does diagnostic trouble code P0113 mean on a 2017 Toyota Sienna?
P0113 is set when the ECM sees the intake air temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold air temperature (often below −40 °F / −40 °C). This is the textbook fingerprint of an open circuit at the IAT sensor: a disconnected sensor, a broken signal wire, or a failed sensor element.
What are the symptoms of P0113 on a 2017 Toyota Sienna?
Check Engine Light is illuminated. Slightly harder cold starting in some cases. Mild reduction in fuel economy. Reduced power under hard acceleration (engine adds extra fuel for "cold" air). Often no noticeable drivability problem at all
What causes P0113 on a 2017 Toyota Sienna?
Disconnected or unlatched IAT / MAF-IAT connector (most-common). Open circuit in the IAT signal wire (broken, chafed, or pinched) (common). Failed IAT sensor element (open internally) (common). Corroded sensor connector pins (common). Damaged sensor body from intake backfire (occasional). Failed PCM input (extremely rare) (rare)
Is it safe to drive a 2017 Toyota Sienna with P0113?
In most cases a 2017 Toyota Sienna stays drivable for short trips with P0113 active, but it should be diagnosed and repaired promptly — this is a low-severity code. Ignoring it can lead to further damage or a failed emissions test.