P0113 on a 2017 Honda Civic
Intake Air Temperature High Input
What does P0113 mean on a 2017 Honda Civic?
P0113 is set when the ECM sees the intake air temperature sensor signal voltage above the calibrated maximum — typically a reading that would represent an unrealistically cold air temperature (often below −40 °F / −40 °C). This is the textbook fingerprint of an open circuit at the IAT sensor: a disconnected sensor, a broken signal wire, or a failed sensor element.
Symptoms on a 2017 Honda Civic
- Check Engine Light is illuminated
- Slightly harder cold starting in some cases
- Mild reduction in fuel economy
- Reduced power under hard acceleration (engine adds extra fuel for "cold" air)
- Often no noticeable drivability problem at all
Likely causes on a 2017 Honda Civic
- Disconnected or unlatched IAT / MAF-IAT connector Most commonEstimated repair: $0– $50
- Open circuit in the IAT signal wire (broken, chafed, or pinched) CommonEstimated repair: $80– $350
- Failed IAT sensor element (open internally) CommonEstimated repair: $30– $150
- Corroded sensor connector pins CommonEstimated repair: $30– $200
- Damaged sensor body from intake backfire OccasionalEstimated repair: $30– $200
- Failed PCM input (extremely rare) RareEstimated repair: $400– $1,500
How to diagnose this on a 2017 Honda Civic
-
Confirm where the IAT sensor lives on this engine
Modern engines fall into two configurations: a standalone IAT sensor in the air intake tract, or a combined MAF/IAT assembly where the IAT element is built into the mass airflow housing. Both share P0113 — the diagnostic difference is where to find the connector and which wires carry the IAT signal.
Tools: Vehicle-specific service information
-
Read IAT temperature on the scan tool
A working IAT reads close to ambient air temperature when the engine has been off long enough to cool. Compare to the coolant temperature reading at cold start — they should agree within a few degrees. An IAT reading of "−40 °F" or "−40 °C" is the classic open-circuit fingerprint.
Tools: Scan tool with IAT PID
-
Inspect the connector and wiring
Unplug the IAT connector and inspect for corrosion, water, or bent pins. With the connector unplugged and the key on, the scan tool should still report a fixed "very cold" value — that confirms an open circuit signature is what set the code.
Tools: Electrical contact cleaner, Flashlight
-
Bench-test the IAT sensor with a multimeter
With the sensor removed, measure resistance across its terminals at room temperature. Compare to the service manual — most NTC IAT sensors read 2.0–4.5 kΩ at 68 °F (20 °C). Infinite resistance means the sensor is open and dead. Heating the sensor gently should cause resistance to drop.
Tools: Multimeter, Heat gun or hair dryer (optional), Service spec sheet
-
Jumper test the signal wire
With the IAT disconnected, briefly jumper the signal wire to ground and observe the scan tool reading — it should swing from "very cold" to "very hot" (P0112 territory). If the reading does not change, the wiring or PCM input is at fault rather than the sensor.
Tools: Jumper wire, Scan tool
Known Technical Service Bulletins for the 2015-2019 Honda Civic
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Honda Civic.
- ENGINE Jul 27, 2025
Service Bulletin - Oil leak at timing chain tensioner inspection cover due to possible insufficient sealant adhesion on inspection cover.
NHTSA #11021745 - FUEL/PROPULSION SYSTEM Aug 5, 2024
Dealer Message - American Honda Motor Co., Inc. (AHM) is searching for certain 2018-2020 Accords, 2016-2020 Civics, 2017-2020 CR-Vs, & 2018-2020 Odysseys that have been diagnosed to be in need of the low-pressure fuel pump, fuel strainer, fuel meter or fuel tank replacement.
NHTSA #11006249 - FUEL/PROPULSION SYSTEM Jul 21, 2024
Dealer Message - American Honda Motor Co., Inc. (AHM) is searching for certain 2018-2020 Accords, 2016-2020 Civics, 2017-2020 CR-Vs, & 2018-2020 Odysseys that have been diagnosed to be in need of the low-pressure fuel pump, fuel strainer, fuel meter or fuel tank replacement. If you have a vehicle that match the qualifiers listed below, AHM requests to have the photos of the lock ring & the low-pressure fuel pump flange taken & sent to TIS (click HERE for example photos).
NHTSA #11005271 - FUEL/PROPULSION SYSTEM Jul 5, 2024
Dealer Message - Dealer Message - American Honda Motor Co., Inc. (AHM) is searching for certain 2018-2020 Accords, 2016-2020 Civics, 2017-2020 CR-Vs, & 2018-2020 Odysseys that have been diagnosed to be in need of the low-pressure fuel pump, fuel strainer, fuel meter or fuel tank replacement.
NHTSA #11004264 - VISIBILITY/WIPER Jun 18, 2024
Service Bulletin - Due to a new North America regulation which introduces a new refrigerant and oil requirement, the compressor shaft seal may leak. American Honda is extending the warranty on the A/C compressor shaft seal from the original 3 years to 10 years from the original date of purchase, with no mileage limitation. The new refrigerant and oil may cause swelling of the compressor shaft seal. The swelling may lead to abnormal wearing of the seal which may increase seal gaps around the compressor shaft allowing refrigerant to leak out.
NHTSA #11002711 - VISIBILITY/WIPER Jun 18, 2024
Service Bulletin - American Honda is extending the warranty on the A/C condenser to 10 years from the original date of purchase with unlimited miles. This warranty extension only covers vehicles that have a defective A/C condenser from the factory. The A/C condenser was not manufactured to specification. As a result, corrosion may develop in the form of tiny holes in the condenser tube walls that allow the refrigerant to leak out.
NHTSA #11002705
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
Common fixes
- Reconnect the IAT or MAF-IAT connector
- Replace the IAT sensor (standalone) or the MAF/IAT assembly
- Repair broken IAT signal wire
- Clean corroded sensor connector pins
About the 2015-2019 Honda Civic
The 2015-2019 Honda Civic was commonly sold with the following powertrains: 2.0L I4, 1.5L Turbo I4, 1.8L I4. Common trims include LX, Sport, EX, Touring.
P0113 vs P0112
These are the two ends of the same circuit:
- P0112 — IAT signal reads too low (sensor sees a very high temperature, often “300 °F”). Usually a shorted-to-ground signal wire or a sensor failed in the closed direction.
- P0113 — IAT signal reads too high (sensor sees a very low temperature, often “−40 °F”). Usually an open circuit — disconnected, broken wire, or sensor open internally.
Why P0113 rarely affects drivability
Modern ECMs use the IAT for relatively minor fuel-trim corrections and to fine-tune cold-start enrichment. With a missing IAT signal, the ECM uses a default value (usually around 70 °F) and the engine runs essentially normally. This is why many drivers report P0113 with no symptoms at all beyond the Check Engine Light.
Combined MAF/IAT assemblies
On most modern vehicles the IAT is integrated into the MAF housing as a single assembly. When the IAT element fails, the entire MAF assembly must be replaced — there is no separate IAT to service. Confirm the part number before ordering; combined assemblies are 4–10× the cost of a standalone IAT.