P0017 on a 2017 Jeep Grand Cherokee
Crank/Cam Correlation (Bank 1 Exhaust)
P0017 on a 2017 Jeep Grand Cherokee indicates crank/cam correlation (bank 1 exhaust). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is stretched timing chain or worn timing chain guides (typically $800–$3,500). Confirm the root cause before replacing parts.
What does P0017 mean on a 2017 Jeep Grand Cherokee?
P0017 is the exhaust-cam counterpart of P0016. The ECM compares the crankshaft position signal to the Bank 1 exhaust camshaft position signal and finds them more than a calibrated number of degrees out of alignment. This usually means timing chain stretch, a stuck cam phaser unable to return to base position, or a position sensor producing bad data. P0017 is one of the strongest indicators of timing chain wear on engines with dual VVT.
This guide covers P0017 across the 2015-2019 Jeep Grand Cherokee generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Jeep Grand Cherokee with P0017?
In most cases a 2017 Jeep Grand Cherokee stays drivable for short trips with P0017 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0017 on a 2017 Jeep Grand Cherokee?
- Check Engine Light is illuminated
- Cold-start rattle or chirp from the front timing cover
- Hard cold start with long crank times
- Loss of low-end torque
- Rough idle and reduced throttle response
- Reduced fuel economy
- Possible engine no-start if timing has slipped enough
What causes P0017 on a 2017 Jeep Grand Cherokee?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Stretched timing chain or worn timing chain guides | Most common | $800–$3,500 |
| Stuck exhaust cam phaser cannot return to base timing | Common | $400–$1,500 |
| Failed exhaust cam position sensor producing inaccurate readings | Common | $100–$400 |
| Low oil pressure preventing the phaser from holding position | Occasional | $50–$200 |
| Damaged exhaust cam reluctor wheel or tone ring | Occasional | $300–$1,500 |
| Stuck-open exhaust VVT oil control valve | Occasional | $100–$450 |
| Timing chain skipped one tooth after a tensioner failure | Rare | $1,000–$4,000 |
How to diagnose this on a 2017 Jeep Grand Cherokee
-
Check oil level and pressure
P0017 with low oil pressure is the exhaust phaser unable to hold commanded position. Confirm level on level ground with a warm engine and measure oil pressure with a mechanical gauge before replacing parts.
Tools: Dipstick, Mechanical oil pressure gauge
-
Watch exhaust cam vs. crank position in live data
The cam-crank offset should remain fixed. An offset that drifts as RPM rises indicates timing chain stretch. A static but wrong offset can mean the chain jumped a tooth. Compare to service-manual specifications.
Tools: Scan tool with dual position PIDs
-
Listen for chain noise at cold start
A 1–3 second cold-start rattle that quiets as oil pressure builds is early chain wear. Continuous rattle indicates advanced wear with imminent failure risk. Use a mechanic's stethoscope on the front timing cover.
Tools: Mechanic's stethoscope
-
Test the exhaust cam sensor electrically
Disconnect the sensor and inspect the connector. With a scope, check the signal pattern — should be a clean square wave with no missing pulses. A noisy or absent signal sets P0017 even with a perfect chain.
Tools: Oscilloscope or scan tool with raw sensor PIDs, Multimeter
-
Inspect the cam phaser on engines with documented failures
On Ford 5.4 3V Triton, GM 3.6 LFX/LLT, BMW N20/N26, and VW EA888 engines, the exhaust phaser is a common P0017 cause independent of chain wear. A scope on the cam sensor while bidirectionally commanding the OCV will show whether the phaser is responding.
Tools: Bidirectional scan tool, Oscilloscope (optional)
NHTSA complaints & recalls for the 2017 Jeep Grand Cherokee
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Jeep Grand Cherokee. Use these to gauge how common a problem is on your specific vehicle before you start chasing Jeep Grand Cherokee diagnostics.
- ENGINE 99
- POWER TRAIN 87
- ELECTRICAL SYSTEM 86
- UNKNOWN OR OTHER 76
- FUEL/PROPULSION SYSTEM 30
6 active recalls
- ELECTRICAL SYSTEM:WIRING May 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger…
NHTSA campaign 18V332000 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE) Nov 2020
Chrysler (FCA US LLC) is recalling certain 2014-2019 Jeep Grand Cherokee vehicles equipped with the 3.0L EcoDiesel engines. The Exhaust Gas Recirculation (EGR) cooler may crack and allow pre-heated vaporized coolant to enter the EGR system. This mixture may combust inside the…
NHTSA campaign 20V699000 - EQUIPMENT Sep 2016
Chrysler (FCA US LLC) is recalling certain model year 2017 Jeep Grand Cherokee manufactured August 8, 2016 through August 16, 2016. In the affected vehicles, the rear tow hook bracket or tow eye bracket may be loose.…
NHTSA campaign 16V686000 - ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER Oct 2017
Accessible Technologies, Inc. (ATI) is recalling certain ProCharger Superchargers, model numbers AB037A-100, AB037A-100P, and A037A-100B, sold for installation on 2012-2017 Jeep Grand Cherokee SRT8 and SRT vehicles. The supercharger mounting bracket may contact and damage the AB…
NHTSA campaign 17E061000
How do I fix P0017 on a 2017 Jeep Grand Cherokee?
- Replace timing chain, guides, tensioner, and sprockets as a complete kit
- Replace the exhaust cam phaser / VVT actuator
- Replace the exhaust cam position sensor
- Service or replace the exhaust-side VVT oil control valve
- Address any underlying oil pressure or sludge issue
About the 2015-2019 Jeep Grand Cherokee
The 2015-2019 Jeep Grand Cherokee was commonly sold with the following powertrains: 3.6L Pentastar V6, 5.7L HEMI V8, 3.0L EcoDiesel V6. Common trims include Laredo, Limited, Overland, Summit.
P0017 on chain-stretch-prone engines
P0017 on these engines should be assumed to be a timing chain problem until proven otherwise — they all have documented chain wear issues:
- GM 3.6 LFX / LLT / LF1 — chain stretch around 80–120k miles
- BMW N20 / N26 2.0T — chronic catastrophic chain failure
- VW / Audi EA888 Gen 1 + 2 — chain stretch at 80–100k
- Ford 5.4 3V Triton V8 — combined phaser and chain failure
- Hyundai / Kia Theta II 2.4 — chain and tensioner failure
On these engines, replace the chain as a complete kit (chain, guides, tensioner, sprockets). Half-replacing leads to repeat failure within 30–50k miles.
Why ignoring P0017 risks engine destruction
The progression of timing chain wear on these engines is:
- P0017 sets intermittently — chain has stretched enough to drift
- P0017 sets every drive cycle — wear is consistent
- Chain rattle becomes audible from the cab
- Chain skips a tooth — valves contact pistons on interference engines
- Engine destroyed — bent valves, possibly damaged head and pistons
The repair bill jumps from $1,500–$3,500 (timing job) at step 2 to $4,000–$10,000+ (rebuilt head or new engine) at step 5. P0017 on a known-affected engine should be fixed within weeks.
P0017 vs P0016
- P0016 — Bank 1 intake cam correlation off
- P0017 — Bank 1 exhaust cam correlation off
Both setting together is strong evidence of timing chain wear since the chain affects both cams equally. Just one bank or one cam setting alone is more likely a single phaser or sensor.
P0017 on a 2017 Jeep Grand Cherokee: frequently asked questions
What does diagnostic trouble code P0017 mean on a 2017 Jeep Grand Cherokee?
P0017 is the exhaust-cam counterpart of P0016. The ECM compares the crankshaft position signal to the Bank 1 exhaust camshaft position signal and finds them more than a calibrated number of degrees out of alignment. This usually means timing chain stretch, a stuck cam phaser unable to return to base position, or a position sensor producing bad data. P0017 is one of the strongest indicators of timing chain wear on engines with dual VVT.
What are the symptoms of P0017 on a 2017 Jeep Grand Cherokee?
Check Engine Light is illuminated. Cold-start rattle or chirp from the front timing cover. Hard cold start with long crank times. Loss of low-end torque. Rough idle and reduced throttle response. Reduced fuel economy. Possible engine no-start if timing has slipped enough
What causes P0017 on a 2017 Jeep Grand Cherokee?
Stretched timing chain or worn timing chain guides (most-common). Stuck exhaust cam phaser cannot return to base timing (common). Failed exhaust cam position sensor producing inaccurate readings (common). Low oil pressure preventing the phaser from holding position (occasional). Damaged exhaust cam reluctor wheel or tone ring (occasional). Stuck-open exhaust VVT oil control valve (occasional). Timing chain skipped one tooth after a tensioner failure (rare)
Is it safe to drive a 2017 Jeep Grand Cherokee with P0017?
In most cases a 2017 Jeep Grand Cherokee stays drivable for short trips with P0017 active, but it should be diagnosed and repaired promptly — this is a high-severity code. Ignoring it can lead to further damage or a failed emissions test.