P0014 on a 2012 Honda Odyssey
Exhaust Cam Over-Advanced (Bank 1, VVT)
P0014 on a 2012 Honda Odyssey indicates exhaust cam over-advanced (bank 1, vvt). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is stuck or sludged exhaust-side vvt oil control valve (typically $100–$450). Confirm the root cause before replacing parts.
What does P0014 mean on a 2012 Honda Odyssey?
P0014 is set when the engine control module commands the Bank 1 exhaust camshaft to a specific advance position and the actual cam position does not match within tolerance. On engines with dual-cam VVT (intake + exhaust phasers), P0014 is the exhaust-side counterpart of P0011. The cause is almost always the same family of failures: a stuck oil control valve, dirty oil starving the phaser, or the phaser itself failing.
This guide covers P0014 across the 2010-2014 Honda Odyssey generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Honda Odyssey with P0014?
In most cases a 2012 Honda Odyssey stays drivable for short trips with P0014 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0014 on a 2012 Honda Odyssey?
- Check Engine Light is illuminated
- Rough idle, particularly when the engine is hot
- Reduced low-end torque and slow throttle response
- Increased emissions at idle
- Possible engine stalling at low RPM
- Slight reduction in fuel economy
- Cold-start rattle from the cam area
What causes P0014 on a 2012 Honda Odyssey?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Stuck or sludged exhaust-side VVT oil control valve | Most common | $100–$450 |
| Low engine oil level or pressure starving the exhaust cam phaser | Most common | $50–$200 |
| Sludged oil passages from skipped maintenance | Common | $100–$600 |
| Failed exhaust cam phaser / VVT actuator | Common | $600–$1,800 |
| Stretched timing chain affecting exhaust cam position | Occasional | $800–$3,000 |
| Damaged exhaust cam sensor wiring or connector | Occasional | $80–$350 |
How to diagnose this on a 2012 Honda Odyssey
-
Confirm oil level, condition, and pressure first
VVT systems are oil-powered. Verify level is at full on a level surface with a warm engine, oil is clean (not dark or sludgy), and viscosity matches the OEM spec. Measure oil pressure with a mechanical gauge — typical 15–25 psi at idle, 40–60 psi at 2500 RPM. Low pressure must be fixed before chasing VVT parts.
Tools: Mechanical oil pressure gauge, Dipstick / level check
-
Read live exhaust cam position vs. commanded position
Scan-tool live data shows commanded and actual cam position. Watch while bidirectionally commanding cam advance. A working system tracks within 1–2 degrees of command. Lag of 5 degrees or oscillation points at the actuator or oil control valve.
Tools: Bidirectional scan tool with cam position PIDs
-
Inspect and clean the exhaust-side oil control valve
Remove the exhaust-side OCV. Check the inlet screen for sludge or metal debris. Bench-test with 12 V — the valve should click and open. Air should pass freely when energized and seal when de-energized. A sticking valve causes the most common P0014.
Tools: Socket set, Brake cleaner (NOT MAF-safe), 12 V test source, Compressed air
-
Listen for cam phaser noise at startup
A failing exhaust phaser often rattles at cold start for 1–3 seconds. Use a mechanic's stethoscope at the front of the cylinder head. The noise stops as oil pressure builds. Continuous rattle indicates advanced phaser wear.
Tools: Mechanic's stethoscope
-
Verify timing chain integrity (specific engines)
On engines with documented chain wear (BMW N20/N26, Ford 5.4 3V, VW EA888, GM 3.6 LFX), the phaser cannot fully advance once the chain has stretched — P0014 sets even with a perfect phaser. Check live cam-crank correlation drift under load.
Tools: Scan tool with cam-crank correlation
NHTSA complaints & recalls for the 2012 Honda Odyssey
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Honda Odyssey. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda Odyssey diagnostics.
- ENGINE 39
- POWER TRAIN 24
- SERVICE BRAKES 60
- ELECTRICAL SYSTEM 33
- STRUCTURE 25
5 active recalls
- SEATS:MID/REAR ASSEMBLY Nov 2017
Honda (American Honda Motor Co.) is recalling certain 2011-2017 Honda Odyssey vehicles. The second row outboard seats can slide sideways to one of two positions. If a seat is placed between either of the two positions when attaching the seat to the vehicle floor, the seat will…
NHTSA campaign 17V725000 - SEATS:MID/REAR ASSEMBLY Dec 2016
Honda (American Honda Motor Co.) is recalling certain model year 2011-2016 Odyssey vehicles manufactured August 17, 2010, to October 1, 2015. The affected vehicles have second row outboard seats that have a release lever that allows the seats to move for easier access to the thi…
NHTSA campaign 16V933000 - SUSPENSION:FRONT Dec 2011
HONDA IS RECALLING CERTAIN MODEL YEAR 2012, ODYSSEY VEHICLES MANUFACTURED FROM OCTOBER 31, 2011, THROUGH NOVEMBER 30, 2011. THE RETENTION NUT FOR THE FRONT RIGHT LOWER SUSPENSION DAMPER BOLT MAY NOT HAVE BEEN TIGHTENED TO THE PROPER TORQUE, POTENTIALLY ALLOWING THE NUT TO LOOSEN…
NHTSA campaign 11V602000 - POWER TRAIN:AUTOMATIC TRANSMISSION Apr 2013
Honda is recalling certain model year 2012-2013 CR-V, Odyssey, and model year 2013 Acura RDX vehicles. During sub-freezing temperatures, the brake-shift interlock blocking mechanism may become slow and allow the gear selector to be moved from the Park position without pressing t…
NHTSA campaign 13V143000
How do I fix P0014 on a 2012 Honda Odyssey?
- Change engine oil and filter with the correct OEM viscosity
- Clean or replace the exhaust-side VVT oil control valve
- Replace the exhaust cam phaser / actuator assembly
- Replace stretched timing chain and components as a kit
- Repair damaged cam sensor wiring
About the 2010-2014 Honda Odyssey
The 2010-2014 Honda Odyssey was commonly sold with the following powertrains: 3.5L V6. Common trims include LX, EX, EX-L, Touring, Elite.
P0014 vs P0011
These two codes describe the same kind of fault on different camshafts:
- P0011 — intake cam Bank 1 timing over-advanced
- P0014 — exhaust cam Bank 1 timing over-advanced
Engines with dual VVT have separate phasers and separate oil control valves for intake and exhaust. P0011 and P0014 setting together points to a common cause (oil pressure, sludge, common chain issue). P0014 alone isolates to the exhaust-side hardware.
Why oil maintenance matters more than the phaser itself
Most P0014 cases on engines with under 100,000 miles trace back to oil maintenance: extended intervals, wrong viscosity, or a slow oil leak that drops level over time. The cam phaser is mechanically robust if fed clean, high-pressure oil. A $50 oil change has resolved more P0014 codes than any other single repair.
Engines that disproportionately set P0014
- Toyota 2GR-FE V6 — exhaust OCV failure around 100k miles
- Ford 3.5L EcoBoost V6 (Gen 1) — phaser rattle leading to P0014
- Hyundai/Kia Theta II 2.4 GDI — both P0011 and P0014 from oil sludge
- GM 3.6 LFX/LLT V6 — chain stretch progresses from P0017 to P0014
P0014 on a 2012 Honda Odyssey: frequently asked questions
What does diagnostic trouble code P0014 mean on a 2012 Honda Odyssey?
P0014 is set when the engine control module commands the Bank 1 exhaust camshaft to a specific advance position and the actual cam position does not match within tolerance. On engines with dual-cam VVT (intake + exhaust phasers), P0014 is the exhaust-side counterpart of P0011. The cause is almost always the same family of failures: a stuck oil control valve, dirty oil starving the phaser, or the phaser itself failing.
What are the symptoms of P0014 on a 2012 Honda Odyssey?
Check Engine Light is illuminated. Rough idle, particularly when the engine is hot. Reduced low-end torque and slow throttle response. Increased emissions at idle. Possible engine stalling at low RPM. Slight reduction in fuel economy. Cold-start rattle from the cam area
What causes P0014 on a 2012 Honda Odyssey?
Stuck or sludged exhaust-side VVT oil control valve (most-common). Low engine oil level or pressure starving the exhaust cam phaser (most-common). Sludged oil passages from skipped maintenance (common). Failed exhaust cam phaser / VVT actuator (common). Stretched timing chain affecting exhaust cam position (occasional). Damaged exhaust cam sensor wiring or connector (occasional)
Is it safe to drive a 2012 Honda Odyssey with P0014?
In most cases a 2012 Honda Odyssey stays drivable for short trips with P0014 active, but it should be diagnosed and repaired promptly — this is a high-severity code. Ignoring it can lead to further damage or a failed emissions test.