P0013 on a 2012 Kia Forte
Exhaust Cam Actuator Circuit Fault (Bank 1)
P0013 on a 2012 Kia Forte indicates exhaust cam actuator circuit fault (bank 1). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed exhaust ocv / vvt solenoid coil (open or shorted) (typically $100–$450). Confirm the root cause before replacing parts.
What does P0013 mean on a 2012 Kia Forte?
P0013 is an electrical-circuit fault on the Bank 1 exhaust camshaft position actuator (OCV / VVT solenoid). The ECM cannot detect the expected current draw when it commands the solenoid, indicating an open circuit, short, or failed driver. Unlike P0014 (over-advanced) which is a position fault, P0013 is specifically a wiring / coil fault — the ECM is reporting that it cannot even communicate with the actuator.
This guide covers P0013 across the 2010-2014 Kia Forte generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Kia Forte with P0013?
In most cases a 2012 Kia Forte stays drivable for short trips with P0013 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0013 on a 2012 Kia Forte?
- Check Engine Light is illuminated
- Loss of mid-range torque
- Rough idle when warm
- Hesitation or stumble on light acceleration
- Reduced fuel economy
- Possible engine stalling at low RPM
What causes P0013 on a 2012 Kia Forte?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed exhaust OCV / VVT solenoid coil (open or shorted) | Most common | $100–$450 |
| Damaged OCV connector or chafed signal wiring | Common | $50–$250 |
| Corroded connector pins from heat / oil exposure | Common | $30–$200 |
| Shorted-to-power or shorted-to-ground OCV wire | Occasional | $80–$350 |
| Failed PCM driver for the exhaust OCV (rare) | Rare | $400–$1,500 |
How to diagnose this on a 2012 Kia Forte
-
Measure OCV coil resistance
Unplug the exhaust-side OCV on Bank 1. Measure resistance across the solenoid terminals. Most OCVs read 6 to 15 Ω. Infinite resistance is an open coil; near zero is a shorted coil. Either requires solenoid replacement.
Tools: Multimeter, Service spec sheet
-
Inspect the connector
Unplug the connector and look closely for corrosion, bent pins, oil intrusion, or melted insulation. The OCV lives in a hot, oily environment and connectors degrade. Clean with electrical contact cleaner.
Tools: Electrical contact cleaner, Magnifying glass
-
Verify wiring continuity to the PCM
With the OCV disconnected and the connector unplugged at the PCM, measure continuity between each wire and its corresponding PCM pin. Open circuit indicates a broken wire. Short to ground or to power indicates chafed insulation contacting nearby metal or a power source.
Tools: Multimeter, Wiring diagram, Back-probe pins
-
Command the OCV with a scan tool
Bidirectional scan tools can command the OCV on and off while watching live current draw. A working solenoid clicks audibly when commanded. No click + a P0013 confirms either the coil or the wiring.
Tools: Bidirectional scan tool
-
Test for shorted wiring at the engine harness
With the engine off and the OCV unplugged, key on, briefly check the supply wire for unexpected voltage. A "hot" wire with the PCM not commanding the OCV indicates a short to power in the harness.
Tools: Multimeter
NHTSA complaints & recalls for the 2012 Kia Forte
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Kia Forte. Use these to gauge how common a problem is on your specific vehicle before you start chasing Kia Forte diagnostics.
- ENGINE 159
- SERVICE BRAKES 50
- AIR BAGS 35
- ELECTRICAL SYSTEM 31
- EXTERIOR LIGHTING 23
4 active recalls
- ENGINE Dec 2020
Kia Motors America (Kia) is recalling certain 2012-2013 Sorento, 2012-2015 Forte and Forte Koup, 2011-2013 Optima Hybrid, 2014-2015 Soul, and 2012 Sportage vehicles. An engine compartment fire can occur while driving.…
NHTSA campaign 20V750000 - AIR BAGS: AIR BAG/RESTRAINT CONTROL MODULE Jun 2018
Kia Motors America (Kia) is recalling certain 2010-2013 Kia Forte, Forte Koup, 2011-2013 Kia Optima and 2011-2012 Kia Optima Hybrid and Sedona vehicles. In the event of a crash, the air bag control unit (ACU) may short circuit, preventing the frontal air bags and seat belt prete…
NHTSA campaign 18V363000 - SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES Dec 2017
Kia Motors America (Kia) is recalling certain 2012-2014 Forte and Forte Koup vehicles. The brake pedal stopper pad can deteriorate allowing the brake light switch plunger to remain extended when the brake pedal is released. This will allow the brake lights to remain illuminated…
NHTSA campaign 17V773000 - SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE Sep 2023
Kia America, Inc. (Kia) is recalling certain 2010-2019 Borrego, 2014-2016 Cadenza, 2010-2013 Forte, Forte Koup, Sportage, 2015-2018 K900, 2011-2015 Optima, 2011-2013 Optima Hybrid, Soul, 2012-2017 Rio, 2011-2014 Sorento, and 2010-2011 Rondo vehicles. The Hydraulic Electronic Con…
NHTSA campaign 23V652000
How do I fix P0013 on a 2012 Kia Forte?
- Replace the exhaust-side VVT oil control valve / OCV
- Repair damaged OCV connector or wiring
- Clean corroded connector pins
- Repair shorted-to-power or shorted-to-ground signal wire
About the 2010-2014 Kia Forte
The 2010-2014 Kia Forte was commonly sold with the following powertrains: 2.0L I4, 1.6L Turbo I4. Common trims include LX, LXS, GT-Line, GT.
P0013 vs P0014
These are the two ways the exhaust VVT system fails on the same hardware:
- P0013 — electrical fault. The ECM cannot drive the solenoid because the circuit is open, shorted, or the coil is dead. No hydraulic action happens at all.
- P0014 — position fault. The solenoid IS being driven, but the cam position does not match what was commanded. The hydraulic side is the problem (sludged passages, failed phaser).
Diagnostic approach differs: P0013 is electrical (resistance, wiring, connector). P0014 is hydraulic (oil pressure, OCV mechanical function, phaser).
When P0013 is the cheap fix
Roughly 60–70 % of P0013 cases trace to the solenoid coil itself — which is a $40–$150 OEM part on most engines and a 10-minute replacement. The other 30–40 % are wiring or connector issues that require a multimeter and patience. The PCM driver failing is rare; do not assume PCM is the cause until everything else has been ruled out.
Why OCV connectors fail in the oil-rich engine bay
The exhaust-side OCV sits on top of the cylinder head — high heat, oil mist, and constant vibration. Standard connector seals harden and crack within 8–10 years of normal use, letting oil migrate up the harness and into the connector. The fix is the connector or the sub-harness, not the OCV.
P0013 on a 2012 Kia Forte: frequently asked questions
What does diagnostic trouble code P0013 mean on a 2012 Kia Forte?
P0013 is an electrical-circuit fault on the Bank 1 exhaust camshaft position actuator (OCV / VVT solenoid). The ECM cannot detect the expected current draw when it commands the solenoid, indicating an open circuit, short, or failed driver. Unlike P0014 (over-advanced) which is a position fault, P0013 is specifically a wiring / coil fault — the ECM is reporting that it cannot even communicate with the actuator.
What are the symptoms of P0013 on a 2012 Kia Forte?
Check Engine Light is illuminated. Loss of mid-range torque. Rough idle when warm. Hesitation or stumble on light acceleration. Reduced fuel economy. Possible engine stalling at low RPM
What causes P0013 on a 2012 Kia Forte?
Failed exhaust OCV / VVT solenoid coil (open or shorted) (most-common). Damaged OCV connector or chafed signal wiring (common). Corroded connector pins from heat / oil exposure (common). Shorted-to-power or shorted-to-ground OCV wire (occasional). Failed PCM driver for the exhaust OCV (rare) (rare)
Is it safe to drive a 2012 Kia Forte with P0013?
In most cases a 2012 Kia Forte stays drivable for short trips with P0013 active, but it should be diagnosed and repaired promptly — this is a high-severity code. Ignoring it can lead to further damage or a failed emissions test.