P0011 on a 2022 Honda HR-V
Intake Cam Over-Advanced (Bank 1, VVT)
P0011 on a 2022 Honda HR-V indicates intake cam over-advanced (bank 1, vvt). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is stuck or contaminated vvt oil control valve / solenoid (typically $100–$450). Confirm the root cause before replacing parts.
What does P0011 mean on a 2022 Honda HR-V?
P0011 is set when the engine control module commands a variable valve-timing (VVT) advance on the Bank 1 intake camshaft and the actual cam position does not match the commanded position within tolerance. The intake cam is stuck advanced, lagging the command, or oscillating. On most modern engines this is the textbook code for a stuck VVT solenoid, a dirty oil control valve, or oil starvation at the cam phaser.
This guide covers P0011 across the 2020-2024 Honda HR-V generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Honda HR-V with P0011?
In most cases a 2022 Honda HR-V stays drivable for short trips with P0011 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0011 on a 2022 Honda HR-V?
- Check Engine Light is illuminated
- Rough idle, especially at startup
- Loss of power and torque, particularly in mid-range RPM
- Stalling at idle or when coming to a stop
- Reduced fuel economy
- Engine may enter limp mode with limited throttle response
- Possible rattling sound from the cam area at startup
What causes P0011 on a 2022 Honda HR-V?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Stuck or contaminated VVT oil control valve / solenoid Cleaning or replacing the oil control valve resolves a majority of P0011 cases. | Most common | $100–$450 |
| Low engine oil level or low oil pressure starving the VVT system Always check oil level and pressure before replacing parts. | Most common | $50–$200 |
| Clogged VVT oil passages from skipped oil changes Sludge from extended oil change intervals blocks small VVT passages. | Common | $100–$600 |
| Failed or worn cam phaser (variable valve timing actuator) | Common | $600–$1,800 |
| Worn or stretched timing chain affecting cam position accuracy | Occasional | $800–$3,000 |
| Failed camshaft position sensor producing inaccurate readings | Occasional | $100–$400 |
| Wiring fault between PCM and VVT solenoid | Rare | $80–$350 |
How to diagnose this on a 2022 Honda HR-V
-
Check engine oil level and condition first
Low oil level is the single most common cause of P0011 set events on engines with a working VVT system. Check level on level ground with the engine warm. If the oil is dark, sludgy, or smells burnt, change it with the correct viscosity before any other diagnosis.
Tools: Dipstick (most engines), Replacement oil and filter (if needed)
-
Measure engine oil pressure
Variable valve timing requires oil pressure typically 15–25 psi at idle and 40–60 psi at higher RPM. Tee a mechanical oil pressure gauge into the oil pressure sender port. Low pressure means a tired oil pump or worn bearings — fix that root cause before replacing VVT parts.
Tools: Mechanical oil pressure gauge
-
Inspect and clean the VVT oil control valve
Remove the oil control valve (OCV) on Bank 1. Inspect the filter screen for sludge or metal. Clean the valve with brake cleaner and a soft brush. Compressed air should pass freely when the valve is energized with 12 V and block when de-energized. A valve that sticks in either position is the cause.
Tools: Socket set, Brake cleaner, 12 V test source, Compressed air
-
Command VVT actuation with a scan tool
Bidirectional scan tools can command intake cam advance and retract while watching live cam-position PIDs. A healthy system responds smoothly and proportionally. A system that lags, oscillates, or does not move points to the actuator (cam phaser) itself.
Tools: Bidirectional scan tool with VVT command function
-
Inspect timing chain stretch
On engines with documented timing chain wear (Ford 5.4 3V, BMW N20/N26, GM 3.6 LFX/LLT, Hyundai/Kia Theta II, VW EA888 1st gen), check live cam-crank correlation drift. Stretched chains cause cam timing to slip retarded over time, and the VVT system cannot compensate enough — P0011 sets.
Tools: Scan tool with cam-crank correlation PIDs
NHTSA complaints & recalls for the 2022 Honda HR-V
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Honda HR-V. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda HR-V diagnostics.
- ENGINE 16
- POWER TRAIN 14
- VEHICLE SPEED CONTROL 12
- ELECTRICAL SYSTEM 24
- UNKNOWN OR OTHER 14
3 active recalls
- BACK OVER PREVENTION:DISPLAY FUNCTION Feb 2023
Honda (American Honda Motor Co.) is recalling certain 2018-2020 Fit and 2019-2022 HR-V vehicles. The rearview camera image may not display when the engine is started with a key, due to a design error in the audio display power circuit. As such, these vehicles fail to comply wit…
NHTSA campaign 23V046000 - AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION:FRONT PASSENGER Feb 2024
Honda (American Honda Motor Co.) is recalling certain 2020-2022 Pilot, Accord, Civic sedan, HR-V, Odyssey, 2020 Civic coupe, Fit, 2021-2022 Civic hatchback, 2021 Civic Type R, Insight, 2020-2021 CR-V, CR-V Hybrid, Passport, Ridgeline, Accord Hybrid, 2020 Acura MDX, 2022 Acura MDX…
NHTSA campaign 24V064000 - BACK OVER PREVENTION:DISPLAY FUNCTION May 2024
Honda (America Honda Motor Co.) is recalling certain 2018-2020 Fit and 2019-2022 HR-V vehicles that were previously recalled under NHTSA recall number 23V-046. The rearview camera image may not display when the engine is started with a key, due to a design error in the audio dis…
NHTSA campaign 24V384000
How do I fix P0011 on a 2022 Honda HR-V?
- Change engine oil and filter with correct viscosity
- Clean or replace the VVT oil control valve / solenoid
- Replace the cam phaser / VVT actuator assembly
- Replace stretched timing chain, guides, and tensioner as a kit
- Replace the camshaft position sensor
About the 2020-2024 Honda HR-V
The 2020-2024 Honda HR-V was commonly sold with the following powertrains: 1.8L I4, 2.0L I4. Common trims include LX, Sport, EX, EX-L.
Why VVT codes correlate so strongly with oil maintenance
The variable valve timing system uses high-pressure engine oil as its hydraulic working fluid. Oil that is too thick (wrong viscosity), too dirty (extended intervals), too low (level dropped between changes), or too aerated (worn pump) cannot actuate the cam phaser fast enough — or at all — when the ECM commands a change. Most P0011 cases on engines under 100,000 miles trace back to oil maintenance, not a failed mechanical part.
P0011 on engines with chronic VVT problems
A short list of engines that disproportionately set P0011:
- Toyota 2GR-FE 3.5L V6 (many Camry, Avalon, RAV4, Sienna) — oil control valves clog around 100k miles. Replacement is the standard fix.
- Honda K-series — oil pressure switch / VTC actuator rattle on cold start. Repair often involves the actuator and the oil pressure switch together.
- Ford 5.4L 3V Triton V8 — known chain stretch + cam phaser failure. A full timing job is often required.
- Nissan VQ35 — solenoid failure on Bank 1 is the textbook P0011.
Driving with P0011
The engine will run but with significant power loss and rough idle. The ECM may enter a reduced-power limp mode. Driving short distances is acceptable; long highway trips or heavy loads risk further damage if the underlying issue is oil pressure related. Repair within a few days.