P0011 on a 2017 Honda CR-V
Intake Cam Over-Advanced (Bank 1, VVT)
P0011 on a 2017 Honda CR-V indicates intake cam over-advanced (bank 1, vvt). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is stuck or contaminated vvt oil control valve / solenoid (typically $100–$450). Confirm the root cause before replacing parts.
What does P0011 mean on a 2017 Honda CR-V?
P0011 is set when the engine control module commands a variable valve-timing (VVT) advance on the Bank 1 intake camshaft and the actual cam position does not match the commanded position within tolerance. The intake cam is stuck advanced, lagging the command, or oscillating. On most modern engines this is the textbook code for a stuck VVT solenoid, a dirty oil control valve, or oil starvation at the cam phaser.
This guide covers P0011 across the 2015-2019 Honda CR-V generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Honda CR-V with P0011?
In most cases a 2017 Honda CR-V stays drivable for short trips with P0011 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0011 on a 2017 Honda CR-V?
- Check Engine Light is illuminated
- Rough idle, especially at startup
- Loss of power and torque, particularly in mid-range RPM
- Stalling at idle or when coming to a stop
- Reduced fuel economy
- Engine may enter limp mode with limited throttle response
- Possible rattling sound from the cam area at startup
What causes P0011 on a 2017 Honda CR-V?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Stuck or contaminated VVT oil control valve / solenoid Cleaning or replacing the oil control valve resolves a majority of P0011 cases. | Most common | $100–$450 |
| Low engine oil level or low oil pressure starving the VVT system Always check oil level and pressure before replacing parts. | Most common | $50–$200 |
| Clogged VVT oil passages from skipped oil changes Sludge from extended oil change intervals blocks small VVT passages. | Common | $100–$600 |
| Failed or worn cam phaser (variable valve timing actuator) | Common | $600–$1,800 |
| Worn or stretched timing chain affecting cam position accuracy | Occasional | $800–$3,000 |
| Failed camshaft position sensor producing inaccurate readings | Occasional | $100–$400 |
| Wiring fault between PCM and VVT solenoid | Rare | $80–$350 |
How to diagnose this on a 2017 Honda CR-V
-
Check engine oil level and condition first
Low oil level is the single most common cause of P0011 set events on engines with a working VVT system. Check level on level ground with the engine warm. If the oil is dark, sludgy, or smells burnt, change it with the correct viscosity before any other diagnosis.
Tools: Dipstick (most engines), Replacement oil and filter (if needed)
-
Measure engine oil pressure
Variable valve timing requires oil pressure typically 15–25 psi at idle and 40–60 psi at higher RPM. Tee a mechanical oil pressure gauge into the oil pressure sender port. Low pressure means a tired oil pump or worn bearings — fix that root cause before replacing VVT parts.
Tools: Mechanical oil pressure gauge
-
Inspect and clean the VVT oil control valve
Remove the oil control valve (OCV) on Bank 1. Inspect the filter screen for sludge or metal. Clean the valve with brake cleaner and a soft brush. Compressed air should pass freely when the valve is energized with 12 V and block when de-energized. A valve that sticks in either position is the cause.
Tools: Socket set, Brake cleaner, 12 V test source, Compressed air
-
Command VVT actuation with a scan tool
Bidirectional scan tools can command intake cam advance and retract while watching live cam-position PIDs. A healthy system responds smoothly and proportionally. A system that lags, oscillates, or does not move points to the actuator (cam phaser) itself.
Tools: Bidirectional scan tool with VVT command function
-
Inspect timing chain stretch
On engines with documented timing chain wear (Ford 5.4 3V, BMW N20/N26, GM 3.6 LFX/LLT, Hyundai/Kia Theta II, VW EA888 1st gen), check live cam-crank correlation drift. Stretched chains cause cam timing to slip retarded over time, and the VVT system cannot compensate enough — P0011 sets.
Tools: Scan tool with cam-crank correlation PIDs
NHTSA complaints & recalls for the 2017 Honda CR-V
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Honda CR-V. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda CR-V diagnostics.
- ENGINE 509
- ELECTRICAL SYSTEM 394
- FUEL/PROPULSION SYSTEM 344
- FORWARD COLLISION AVOIDANCE 272
- UNKNOWN OR OTHER 259
7 active recalls
- STEERING:ELECTRIC POWER ASSIST SYSTEM Sep 2018
Honda (American Honda Motor Co.) is recalling certain 2017-2018 Honda Civic and CR-V vehicles. The magnet that controls the torque sensor output signal for the electronic power steering system may not be properly secured, allowing the magnet to become dislodged. During a full…
NHTSA campaign 18V663000 - FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS Jul 2017
Honda (American Honda Motor Co.) is recalling certain 2017 Honda CR-V 2WD and AWD vehicles. The affected vehicles have a fuel supply pipe that may have been improperly manufactured, possibly resulting in the pipe disconnecting and leaking while driving.…
NHTSA campaign 17V442000 - EQUIPMENT:OTHER:LABELS Apr 2017
Honda (American Honda Motor Co.) is recalling certain 2017 CR-V and Acura RDX vehicles. The Certification Labels on the affected vehicles were printed with ink that may be inadvertently wiped away with an alcohol solvent. As such, these vehicles fail to comply with the requirem…
NHTSA campaign 17V256000 - SEAT BELTS:FRONT:BUCKLE ASSEMBLY Mar 2023
Honda (American Honda Motor Co.) is recalling certain 2017-2020 CR-V, 2018-2019 Accord and Accord Hybrid, 2018-2020 Odyssey, 2019 Insight, and 2019-2020 Acura RDX vehicles. A manufacturing issue with the front seat belts may cause the seat belt buckle channel to interfere with t…
NHTSA campaign 23V158000
How do I fix P0011 on a 2017 Honda CR-V?
- Change engine oil and filter with correct viscosity
- Clean or replace the VVT oil control valve / solenoid
- Replace the cam phaser / VVT actuator assembly
- Replace stretched timing chain, guides, and tensioner as a kit
- Replace the camshaft position sensor
About the 2015-2019 Honda CR-V
The 2015-2019 Honda CR-V was commonly sold with the following powertrains: 1.5L Turbo I4, 2.4L I4, 2.0L Hybrid I4. Common trims include LX, EX, EX-L, Touring.
Why VVT codes correlate so strongly with oil maintenance
The variable valve timing system uses high-pressure engine oil as its hydraulic working fluid. Oil that is too thick (wrong viscosity), too dirty (extended intervals), too low (level dropped between changes), or too aerated (worn pump) cannot actuate the cam phaser fast enough — or at all — when the ECM commands a change. Most P0011 cases on engines under 100,000 miles trace back to oil maintenance, not a failed mechanical part.
P0011 on engines with chronic VVT problems
A short list of engines that disproportionately set P0011:
- Toyota 2GR-FE 3.5L V6 (many Camry, Avalon, RAV4, Sienna) — oil control valves clog around 100k miles. Replacement is the standard fix.
- Honda K-series — oil pressure switch / VTC actuator rattle on cold start. Repair often involves the actuator and the oil pressure switch together.
- Ford 5.4L 3V Triton V8 — known chain stretch + cam phaser failure. A full timing job is often required.
- Nissan VQ35 — solenoid failure on Bank 1 is the textbook P0011.
Driving with P0011
The engine will run but with significant power loss and rough idle. The ECM may enter a reduced-power limp mode. Driving short distances is acceptable; long highway trips or heavy loads risk further damage if the underlying issue is oil pressure related. Repair within a few days.
P0011 on a 2017 Honda CR-V: frequently asked questions
What does diagnostic trouble code P0011 mean on a 2017 Honda CR-V?
P0011 is set when the engine control module commands a variable valve-timing (VVT) advance on the Bank 1 intake camshaft and the actual cam position does not match the commanded position within tolerance. The intake cam is stuck advanced, lagging the command, or oscillating. On most modern engines this is the textbook code for a stuck VVT solenoid, a dirty oil control valve, or oil starvation at the cam phaser.
What are the symptoms of P0011 on a 2017 Honda CR-V?
Check Engine Light is illuminated. Rough idle, especially at startup. Loss of power and torque, particularly in mid-range RPM. Stalling at idle or when coming to a stop. Reduced fuel economy. Engine may enter limp mode with limited throttle response. Possible rattling sound from the cam area at startup
What causes P0011 on a 2017 Honda CR-V?
Stuck or contaminated VVT oil control valve / solenoid (most-common). Low engine oil level or low oil pressure starving the VVT system (most-common). Clogged VVT oil passages from skipped oil changes (common). Failed or worn cam phaser (variable valve timing actuator) (common). Worn or stretched timing chain affecting cam position accuracy (occasional). Failed camshaft position sensor producing inaccurate readings (occasional). Wiring fault between PCM and VVT solenoid (rare)
Is it safe to drive a 2017 Honda CR-V with P0011?
In most cases a 2017 Honda CR-V stays drivable for short trips with P0011 active, but it should be diagnosed and repaired promptly — this is a high-severity code. Ignoring it can lead to further damage or a failed emissions test.