P0846 on a 2022 Subaru Forester
Trans Fluid Pressure Sensor B Range / Performance
P0846 on a 2022 Subaru Forester indicates trans fluid pressure sensor b range / performance. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed transmission fluid pressure sensor / switch "b". Confirm the root cause before replacing parts.
What does P0846 mean on a 2022 Subaru Forester?
P0846 is set when the transmission controller reads the "B" transmission fluid pressure sensor or switch and the value it reports does not make sense for the hydraulic state the transmission is supposed to be in. Either the pressure is outside the expected range, or it fails to change when a shift or a clutch application should have changed it. Two very different things produce that: a faulty sensor, or a correctly-working sensor honestly reporting a real hydraulic pressure problem. Which one you have decides whether this is a modest repair or a transmission rebuild, so the diagnosis matters more here than the part.
The symptoms, causes, and diagnostic steps below describe P0846 itself, so they read the same on nearby Subaru Forester model years. Powertrain and trim details vary year to year — confirm the specifics against your own vehicle before buying parts.
Is it safe to drive a 2022 Subaru Forester with P0846?
In most cases a 2022 Subaru Forester stays drivable for short trips with P0846 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0846 on a 2022 Subaru Forester?
- Check Engine Light is illuminated
- Harsh, delayed, or erratic shifts
- Transmission slipping or flaring between gears
- Transmission enters limp / failsafe mode, often locked in one gear
- Reduced fuel economy
- Often paired with P0700 from the transmission controller
What causes P0846 on a 2022 Subaru Forester?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed transmission fluid pressure sensor / switch "B" We have not published a verified cost range for this specific part, and part pricing varies widely between transmissions — ask your shop for the part number and a written quote rather than trusting a generic figure. | Most common | — |
| Damaged wiring or fluid-contaminated external transmission connector | Common | $100–$500 |
| Low transmission fluid level or contaminated fluid | Common | $100–$400 |
| Contaminated fluid causing valve sticking in the valve body | Common | $150–$500 |
| Worn or stuck valve body losing pressure regulation | Occasional | $600–$2,000 |
| Internal transmission damage or a worn pump producing genuinely low pressure | Occasional | $2,500–$6,500 |
| Failed TCM driver or input for the pressure sensor circuit | Rare | $500–$1,500 |
Cost ranges are editorial estimates for parts and labor at an independent U.S. shop — not quotes. What you actually pay moves with your region, the shop's hourly rate, which engine you have, and how much diagnostic time the job takes. Dealer service departments typically sit above these ranges.
How to diagnose this on a 2022 Subaru Forester
-
Check transmission fluid level and condition before anything else
Low fluid produces genuinely low pressure, and the sensor will correctly report it. Follow the vehicle's specific check procedure — most modern transmissions require a defined fluid temperature with the engine running, and many have no dipstick at all. Fluid that smells burnt or shows clutch material tells you the sensor is probably not your problem.
Tools: Vehicle-specific service procedure, Replacement fluid (if needed)
-
Read live pressure data across a full shift sequence
Graph the "B" pressure sensor value while driving through the gear range. A working sensor on a healthy transmission shows pressure rising and falling in step with shifts. A value that never moves is the classic dead-sensor pattern. A value that moves but sits consistently low points at a real hydraulic problem instead.
Tools: Scan tool with transmission pressure PIDs
-
Compare the electronic reading against a mechanical gauge
This is the test that separates the two possibilities cleanly. Connect a mechanical pressure gauge at the transmission's test port and compare it to what the sensor reports. Gauge normal, sensor wrong means the sensor is at fault. Gauge low, sensor matching means the sensor is honest and the hydraulic system is the problem. Not every transmission has an accessible test port — where one exists, use it.
Tools: Transmission pressure gauge set, Vehicle-specific service information
-
Inspect the external transmission connector
Fluid wicking up the harness into the connector produces sensor readings that drift or stick, and it looks like a sensor failure from the controller's side. Unplug the connector and check for fluid inside the body or along the wires. If it is wet, the case seal and the affected harness section are the actual repair.
Tools: Connector unlock tool, Flashlight
-
Drop the pan and inspect the magnet and filter
Brown or grey gritty paste on the pan magnet means clutch material is circulating, and a clogged filter starves the pump — which produces low pressure that the sensor then reports faithfully. Finding either changes the repair from "replace a sensor" to a conversation about the transmission's remaining life.
Tools: Drain pan, Socket set, New filter and gasket
NHTSA complaints & recalls for the 2022 Subaru Forester
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Subaru Forester. Use these to gauge how common a problem is on your specific vehicle before you start chasing Subaru Forester diagnostics.
- ENGINE 10
- VEHICLE SPEED CONTROL 9
- VISIBILITY/WIPER 20
- UNKNOWN OR OTHER 17
- FORWARD COLLISION AVOIDANCE 12
1 active recall
- POWER TRAIN:AUTOMATIC TRANSMISSION:PARK/NEUTRAL START INTERLOCK SWITCH Nov 2023
Subaru of America, Inc. is recalling certain model year 2021 Crosstrek, 2022 Forester, 2021-2023 Legacy, and Outback vehicles. An insufficient weld may allow water to enter the inhibitor switch, causing it to fail.…
NHTSA campaign 23V755000
How do I fix P0846 on a 2022 Subaru Forester?
- Replace the transmission fluid pressure sensor / switch
- Service transmission fluid and filter to the correct specification
- Repair the external transmission connector or harness
- Repair the case seal that allowed fluid intrusion into the harness
- Replace or rebuild the valve body for pressure regulation faults
Engines in the 2022 Subaru Forester
The 2022 Subaru Forester was offered with the 2.5L 4-cylinder engine. Which one you have changes where P0846 is most likely to originate, so confirm your engine before ordering parts.
Engine data: EPA fueleconomy.gov.
The question P0846 is really asking
Every diagnostic decision on this code flows from one question: is the sensor lying, or is the pressure genuinely wrong?
- Sensor lying → replace a sensor, repair some wiring, move on.
- Pressure genuinely wrong → the sensor is doing exactly what it was fitted to do, and the real problem is fluid, the pump, or the valve body.
Nothing else about this code matters as much as answering that. The cleanest way to answer it is to compare the electronic reading against a mechanical pressure gauge at the transmission’s test port, where the vehicle has one. Everything else is inference.
An honest note about the cost of this repair
We list dollar ranges on this site only where we have a range we actually trust. For the pressure sensor itself we do not have one: sensor pricing and access vary enormously between transmission families, from an externally-mounted switch that takes minutes to a sensor buried in the valve body that requires dropping the pan and partially disassembling it.
Rather than print a number that might be wrong by a factor of five, we would rather tell you what to ask for: the part number, the labour hours, and whether the pan has to come down. Those three answers give you a real quote instead of a guess.
Limp mode is a protective feature, not a breakdown
If the transmission drops into failsafe and locks itself in a single gear, that is the controller protecting the hardware because it no longer trusts its pressure information. The vehicle will move — usually in second or third gear, with no upshifts and poor acceleration. It is enough to get home or to a shop at moderate speed.
It is not enough for highway driving, and it is not something to live with for weeks. A transmission operating on unreliable pressure data can apply clutches at the wrong pressure, which is how a sensor problem turns into a clutch problem.
Why fluid is always step one
Low fluid produces low pressure. Low pressure sets pressure codes. It is the most common cause and the cheapest to correct, and it is the one thing you can check before deciding anything else. Check it properly, using the manufacturer’s procedure — an incorrect reading from a casual check has sent plenty of people down an expensive diagnostic path for a transmission that was simply a litre low.
P0846 on a 2022 Subaru Forester: frequently asked questions
What does diagnostic trouble code P0846 mean on a 2022 Subaru Forester?
P0846 is set when the transmission controller reads the "B" transmission fluid pressure sensor or switch and the value it reports does not make sense for the hydraulic state the transmission is supposed to be in. Either the pressure is outside the expected range, or it fails to change when a shift or a clutch application should have changed it. Two very different things produce that: a faulty sensor, or a correctly-working sensor honestly reporting a real hydraulic pressure problem. Which one you have decides whether this is a modest repair or a transmission rebuild, so the diagnosis matters more here than the part.
What are the symptoms of P0846 on a 2022 Subaru Forester?
Check Engine Light is illuminated. Harsh, delayed, or erratic shifts. Transmission slipping or flaring between gears. Transmission enters limp / failsafe mode, often locked in one gear. Reduced fuel economy. Often paired with P0700 from the transmission controller
What causes P0846 on a 2022 Subaru Forester?
Failed transmission fluid pressure sensor / switch "B" (most-common). Damaged wiring or fluid-contaminated external transmission connector (common). Low transmission fluid level or contaminated fluid (common). Contaminated fluid causing valve sticking in the valve body (common). Worn or stuck valve body losing pressure regulation (occasional). Internal transmission damage or a worn pump producing genuinely low pressure (occasional). Failed TCM driver or input for the pressure sensor circuit (rare)
Is it safe to drive a 2022 Subaru Forester with P0846?
In most cases a 2022 Subaru Forester stays drivable for short trips with P0846 active, but it should be diagnosed and repaired promptly — this is a high-severity code. Ignoring it can lead to further damage or a failed emissions test.