P0741 on a 2017 Honda CR-V
Torque Converter Clutch Stuck Off
P0741 on a 2017 Honda CR-V indicates torque converter clutch stuck off. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is worn or burned torque converter clutch friction material (typically $1,800–$4,500). Confirm the root cause before replacing parts.
What does P0741 mean on a 2017 Honda CR-V?
P0741 is set when the ECM (or TCM) commands the torque converter clutch (TCC) to lock up under cruise conditions and does not see the expected drop in engine RPM relative to vehicle speed. Effectively, the lockup clutch is being commanded but not engaging — or it engages and immediately slips. Either way the converter is running in fluid-coupling mode at highway speed when it should be mechanically locked.
This guide covers P0741 across the 2015-2019 Honda CR-V generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2015 through 2019.
Is it safe to drive a 2017 Honda CR-V with P0741?
In most cases a 2017 Honda CR-V stays drivable for short trips with P0741 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0741 on a 2017 Honda CR-V?
- Check Engine Light is illuminated
- Engine RPM at highway cruise is 200–400 RPM higher than normal
- Noticeable fuel economy drop on the highway
- Possible transmission fluid overheating warning on towing
- Shudder or vibration at light-throttle cruise (slipping TCC)
- Often paired with P0700 from the TCM
What causes P0741 on a 2017 Honda CR-V?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Worn or burned torque converter clutch friction material Requires torque converter replacement — major job. | Most common | $1,800–$4,500 |
| Failed TCC solenoid in the valve body | Common | $300–$900 |
| Stuck TCC control valve in the valve body | Common | $400–$1,500 |
| Low transmission fluid level or contaminated fluid | Common | $100–$400 |
| Wiring fault to the TCC solenoid | Occasional | $80–$350 |
| Failed TCM driver for the TCC solenoid | Rare | $500–$1,500 |
| Internal transmission damage allowing fluid bypass | Occasional | $2,500–$6,500 |
How to diagnose this on a 2017 Honda CR-V
-
Check transmission fluid level and condition
Transmission service procedures vary widely — some vehicles require a special procedure to check fluid level at operating temperature with the engine running. Follow the vehicle's specific procedure. Fluid that smells burnt or shows clutch material indicates internal damage; no point chasing the solenoid until the fluid is right.
Tools: Vehicle-specific service procedure, Replacement fluid (if needed)
-
Verify TCC command vs. actual lockup with a scan tool
During highway cruise, watch the TCC duty cycle or commanded state, alongside engine RPM and vehicle speed. The TCC should command on around 45–55 mph and engine RPM should drop 100–300 RPM at the moment of lockup. No RPM drop confirms the TCC is not engaging mechanically.
Tools: Scan tool with TCC and live RPM PIDs
-
Test the TCC solenoid electrically
Locate the TCC solenoid in the wiring diagram (most are accessible through the transmission's external connector). Measure resistance — typical 10–30 Ω depending on the transmission. Confirm continuity and that the TCM commands voltage to the solenoid during the lockup attempt.
Tools: Multimeter, Wiring diagram
-
Inspect transmission external connector for fluid
Disconnect the external transmission connector. Fluid wicking up into the wiring harness from a failed case seal will contaminate the TCM-side connector and cause electrical faults that mimic a solenoid failure. The repair is the seal and often the harness; the solenoid itself may be fine.
Tools: Connector unlock tool, Flashlight
-
Drop the pan and inspect the magnet
A pan magnet covered in fine clutch material — especially brown or black gritty paste — indicates the torque converter clutch has been slipping and shedding material. At that point the converter must be replaced; cleaning is not a fix.
Tools: Drain pan, Socket set, New filter and gasket
NHTSA complaints & recalls for the 2017 Honda CR-V
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Honda CR-V. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda CR-V diagnostics.
- ENGINE 509
- ELECTRICAL SYSTEM 394
- FUEL/PROPULSION SYSTEM 344
- FORWARD COLLISION AVOIDANCE 272
- UNKNOWN OR OTHER 259
7 active recalls
- STEERING:ELECTRIC POWER ASSIST SYSTEM Sep 2018
Honda (American Honda Motor Co.) is recalling certain 2017-2018 Honda Civic and CR-V vehicles. The magnet that controls the torque sensor output signal for the electronic power steering system may not be properly secured, allowing the magnet to become dislodged. During a full…
NHTSA campaign 18V663000 - FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS Jul 2017
Honda (American Honda Motor Co.) is recalling certain 2017 Honda CR-V 2WD and AWD vehicles. The affected vehicles have a fuel supply pipe that may have been improperly manufactured, possibly resulting in the pipe disconnecting and leaking while driving.…
NHTSA campaign 17V442000 - EQUIPMENT:OTHER:LABELS Apr 2017
Honda (American Honda Motor Co.) is recalling certain 2017 CR-V and Acura RDX vehicles. The Certification Labels on the affected vehicles were printed with ink that may be inadvertently wiped away with an alcohol solvent. As such, these vehicles fail to comply with the requirem…
NHTSA campaign 17V256000 - SEAT BELTS:FRONT:BUCKLE ASSEMBLY Mar 2023
Honda (American Honda Motor Co.) is recalling certain 2017-2020 CR-V, 2018-2019 Accord and Accord Hybrid, 2018-2020 Odyssey, 2019 Insight, and 2019-2020 Acura RDX vehicles. A manufacturing issue with the front seat belts may cause the seat belt buckle channel to interfere with t…
NHTSA campaign 23V158000
How do I fix P0741 on a 2017 Honda CR-V?
- Service transmission fluid and filter to the correct specification
- Replace the TCC solenoid (often part of a solenoid pack)
- Repair external transmission wiring or connector
- Replace the torque converter (and usually rebuild the transmission)
- Rebuild or replace the transmission for severe internal damage
About the 2015-2019 Honda CR-V
The 2015-2019 Honda CR-V was commonly sold with the following powertrains: 1.5L Turbo I4, 2.4L I4, 2.0L Hybrid I4. Common trims include LX, EX, EX-L, Touring.
How to tell solenoid failure from converter failure
Both produce P0741, but the symptoms differ slightly:
- Solenoid failure — RPM at cruise is exactly normal-plus-converter-slip (around 200–300 RPM high). The transmission shifts cleanly otherwise. No shudder.
- Converter slipping — RPM at cruise is variable and rises under load. Light-throttle cruise produces a shudder you can feel through the seat and the steering wheel — described by owners as “feels like driving over rumble strips.”
The shudder pattern is diagnostic: solenoid issues don’t shudder; worn TCC friction material shudders during partial lockup.
P0741 with shudder is a transmission job
Once the TCC friction lining is worn to the point of slipping under light load, the converter shedding material accelerates downstream wear in the transmission itself. Driving a P0741 with shudder for months can convert a $1,800 torque-converter-only repair into a $5,000+ rebuild. Treat shuddering P0741 as urgent.
Trans fluid changes after P0741 — proceed with caution
For decades the rule was “if the transmission is starting to fail, do NOT change the fluid — the new clean fluid washes out gunked clutch material and the transmission fails immediately.” Modern fluid technology has changed that advice. A drain-and-fill (not a flush) with the correct OEM fluid is now generally safe and sometimes resolves P0741 if the fluid was degraded. A full machine-flush on a transmission with TCC slip is still risky.
P0741 on a 2017 Honda CR-V: frequently asked questions
What does diagnostic trouble code P0741 mean on a 2017 Honda CR-V?
P0741 is set when the ECM (or TCM) commands the torque converter clutch (TCC) to lock up under cruise conditions and does not see the expected drop in engine RPM relative to vehicle speed. Effectively, the lockup clutch is being commanded but not engaging — or it engages and immediately slips. Either way the converter is running in fluid-coupling mode at highway speed when it should be mechanically locked.
What are the symptoms of P0741 on a 2017 Honda CR-V?
Check Engine Light is illuminated. Engine RPM at highway cruise is 200–400 RPM higher than normal. Noticeable fuel economy drop on the highway. Possible transmission fluid overheating warning on towing. Shudder or vibration at light-throttle cruise (slipping TCC). Often paired with P0700 from the TCM
What causes P0741 on a 2017 Honda CR-V?
Worn or burned torque converter clutch friction material (most-common). Failed TCC solenoid in the valve body (common). Stuck TCC control valve in the valve body (common). Low transmission fluid level or contaminated fluid (common). Wiring fault to the TCC solenoid (occasional). Failed TCM driver for the TCC solenoid (rare). Internal transmission damage allowing fluid bypass (occasional)
Is it safe to drive a 2017 Honda CR-V with P0741?
In most cases a 2017 Honda CR-V stays drivable for short trips with P0741 active, but it should be diagnosed and repaired promptly — this is a high-severity code. Ignoring it can lead to further damage or a failed emissions test.