P0720 on a 2017 Toyota Tacoma
Transmission Output Speed Sensor Malfunction
P0720 on a 2017 Toyota Tacoma means transmission output speed sensor malfunction. P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis. Use the symptoms and test results to narrow down the cause before replacing parts.
What does P0720 mean on a 2017 Toyota Tacoma?
P0720 is set when the transmission control module does not receive a valid signal from the output shaft speed sensor. The TCM uses this signal to compare actual transmission output to expected output for the selected gear and engine RPM — if the signal is missing or implausible, gear ratio calculations fail and the TCM cannot shift correctly. The vehicle typically drops into limp mode (stuck in a default gear, often 3rd or 4th) until the signal is restored.
The symptoms, causes, and diagnostic steps below describe P0720 itself, so they read the same on nearby Toyota Tacoma model years. Powertrain and trim details vary year to year — confirm the specifics against your own vehicle before buying parts.
Is it safe to drive a 2017 Toyota Tacoma with P0720?
P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.
What are the symptoms of P0720 on a 2017 Toyota Tacoma?
- Check Engine Light is illuminated
- Speedometer reads zero or fluctuates erratically
- Transmission locked into a single gear (limp mode)
- Hard, harsh, or no shifts
- Cruise control inoperative
- Vehicle may shudder or hesitate at the moment of shift
- Often paired with P0700 (transmission control malfunction)
What causes P0720 on a 2017 Toyota Tacoma?
Possible causes of P0720 depend on the equipment fitted. Confirm which parts and tests apply on a 2017 Toyota Tacoma before pricing a repair.
| Cause | Estimated repair (USD) |
|---|---|
| Failed output shaft speed sensor element | $150–$500 |
| Damaged sensor connector or harness | $80–$350 |
| Metal debris on the sensor tip (from internal transmission wear) Cleaning the sensor face is a free first attempt. | $100–$400 |
| Damaged tone ring or reluctor wheel inside the transmission | $1,500–$4,500 |
| Transmission fluid contamination preventing the sensor from reading | $200–$700 |
| Wiring fault between the sensor and the TCM | $100–$500 |
| Failed TCM signal input (rare) | $500–$1,500 |
These are editorial estimates in U.S. dollars. A shop can price a confirmed repair using the engine, parts and local labor rate.
How to diagnose this on a 2017 Toyota Tacoma
-
Locate the output speed sensor on this transmission
The output shaft speed sensor is typically a two-wire sensor threaded into the rear of the transmission case (RWD vehicles) or the side of the transaxle (FWD vehicles). Some vehicles have it on the transfer case for 4WD. Confirm location in the service manual.
Tools: Vehicle-specific service information
-
Check connector and visible wiring
Sensor connectors near the transmission case are exposed to heat, road debris, and sometimes fluid leaks. Unplug and inspect for corrosion, transmission fluid migration up the harness, or visible damage. Clean and re-seat.
Tools: Connector unlock tool, Electrical contact cleaner
-
Measure sensor resistance
Most output speed sensors are magnetic or Hall-effect with a typical resistance of 200–1500 Ω. Compare to the service manual. Infinite resistance means an open sensor; near zero means shorted. Either way, replace.
Tools: Multimeter, Service spec sheet
-
Verify signal output during rotation
On a lift with the rear wheels free to rotate, spin a rear wheel slowly by hand while watching the output speed PID. The reading should change in proportion to wheel rotation. No response confirms a dead sensor or damaged tone ring.
Tools: Vehicle lift, Scan tool with output speed PID
-
Inspect sensor tip for debris
Remove the sensor and look at the magnetic tip. Steel slivers stuck to the magnet are normal — large chunks or clutch material is a warning sign that the transmission is shedding material. Clean the tip and reinstall as a first attempt; consider transmission fluid analysis if heavy debris was present.
Tools: Socket, Magnet pick or wire brush
NHTSA complaints & recalls for the 2017 Toyota Tacoma
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2017 Toyota Tacoma. Use these to gauge how common a problem is on your specific vehicle before you start chasing Toyota Tacoma diagnostics.
NHTSA snapshot taken October 21, 2026; refreshed quarterly. For live figures see NHTSA.gov .
- POWER TRAIN 68
- ENGINE 36
- UNKNOWN OR OTHER 37
- SERVICE BRAKES 31
- STRUCTURE 27
5 active recalls
- FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP Nov 2020
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2019 4Runner, 2019-2020 Avalon, 2019 Corolla Hatchback, 2017-2019 Highlander, 2018-2020 Camry, 2020 Corolla, 2018-2019 Land Cruiser, 2017-2020 Tacoma, 2019-2020 RAV4, 2019-2020 Sequoia, 2017-2020 Sienna,…
NHTSA campaign 20V682000 - SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM Apr 2018
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018 Toyota Camry and Highlander vehicles, 2017 Toyota Sienna and Tacoma vehicles and 2017 Lexus RX350 vehicles. During the manufacturing process, the oil galley in the rotor for the brake booster vacuum pump…
NHTSA campaign 18V211000 - EQUIPMENT:OTHER:LABELS Dec 2017
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2017-2018 Toyota 4Runner and Tundra, 2018 Toyota Highlander, RAV4 and Lexus GX460 and 2017 Toyota Sienna and Tacoma vehicles. These vehicles may have incorrect load carrying capacity modification labels. As su…
NHTSA campaign 17V831000 - ENGINE Jun 2017
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2016-2017 Tacoma vehicles equipped with a six-cylinder engine. The affected vehicles have a crank position sensor that may malfunction, potentially resulting in an engine stall.…
NHTSA campaign 17V356000
How do I fix P0720 on a 2017 Toyota Tacoma?
- Clean debris off the output speed sensor tip
- Replace the output shaft speed sensor with an OEM part
- Repair sensor connector or harness damage
- Service transmission fluid (drop pan, replace filter and gasket)
- Internal transmission repair if tone ring or shaft damage is confirmed
Engines in the 2017 Toyota Tacoma
The 2017 Toyota Tacoma was offered with the 2.7L 4-cylinder and 3.5L 6-cylinder engines. Which one you have changes where P0720 is most likely to originate, so confirm your engine before ordering parts.
Engine data: EPA fueleconomy.gov.
Why P0720 puts the transmission into limp mode
The TCM continuously compares output shaft speed to engine RPM and selected gear to verify it is actually getting the gear ratio it commanded. Without a valid output speed signal:
- Ratio verification fails (sets P0731-P0734 in some cases)
- Shift point timing breaks (cannot tell vehicle speed for upshifts)
- Torque converter lockup logic fails (depends on accurate speed)
A transmission may restrict shifting when the output-speed signal is lost. If acceleration or gear engagement is unpredictable, stop safely and arrange assistance. Follow the instructions for the warning displayed on your vehicle.
P0720 with metal on the sensor tip
A small amount of metallic dust on the magnetic sensor tip is normal — it’s the natural wear of bearings and gears over the life of the transmission. Large flakes or clutch material is not normal and indicates internal damage that will eventually cause shifting problems beyond the sensor. If you find heavy debris, do a fluid service and inspect the pan magnet too — together they tell the story of what’s happening inside.
P0720 vs P0500 (Vehicle Speed Sensor)
These can look similar but come from different sources:
- P0500 — vehicle speed signal missing (often the ABS wheel speed sensor on modern vehicles)
- P0720 — transmission output shaft speed signal missing specifically from the transmission’s own sensor
On vehicles where the TCM derives “vehicle speed” from the output shaft sensor, both codes can set together from a single sensor failure.
P0720 on a 2017 Toyota Tacoma: frequently asked questions
What does diagnostic trouble code P0720 mean on a 2017 Toyota Tacoma?
P0720 is set when the transmission control module does not receive a valid signal from the output shaft speed sensor. The TCM uses this signal to compare actual transmission output to expected output for the selected gear and engine RPM — if the signal is missing or implausible, gear ratio calculations fail and the TCM cannot shift correctly. The vehicle typically drops into limp mode (stuck in a default gear, often 3rd or 4th) until the signal is restored.
What are the symptoms of P0720 on a 2017 Toyota Tacoma?
Check Engine Light is illuminated. Speedometer reads zero or fluctuates erratically. Transmission locked into a single gear (limp mode). Hard, harsh, or no shifts. Cruise control inoperative. Vehicle may shudder or hesitate at the moment of shift. Often paired with P0700 (transmission control malfunction)
What causes P0720 on a 2017 Toyota Tacoma?
Failed output shaft speed sensor element (estimated U.S. repair cost $150–$500). Damaged sensor connector or harness (estimated U.S. repair cost $80–$350). Metal debris on the sensor tip (from internal transmission wear) (estimated U.S. repair cost $100–$400). Damaged tone ring or reluctor wheel inside the transmission. Transmission fluid contamination preventing the sensor from reading. Wiring fault between the sensor and the TCM. Failed TCM signal input (rare)
Is it safe to drive a 2017 Toyota Tacoma with P0720?
P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.