P0720 on a 2012 Honda CR-V

Transmission Output Speed Sensor Malfunction

P0720 on a 2012 Honda CR-V means transmission output speed sensor malfunction. P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis. Use the symptoms and test results to narrow down the cause before replacing parts.

Severity: high Check warning lights Compact SUV

Maintained by MECH AI Editorial · Technical content updated

What does P0720 mean on a 2012 Honda CR-V?

P0720 is set when the transmission control module does not receive a valid signal from the output shaft speed sensor. The TCM uses this signal to compare actual transmission output to expected output for the selected gear and engine RPM — if the signal is missing or implausible, gear ratio calculations fail and the TCM cannot shift correctly. The vehicle typically drops into limp mode (stuck in a default gear, often 3rd or 4th) until the signal is restored.

The symptoms, causes, and diagnostic steps below describe P0720 itself, so they read the same on nearby Honda CR-V model years. Powertrain and trim details vary year to year — confirm the specifics against your own vehicle before buying parts.

Is it safe to drive a 2012 Honda CR-V with P0720?

P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.

What are the symptoms of P0720 on a 2012 Honda CR-V?

What causes P0720 on a 2012 Honda CR-V?

Possible causes of P0720 depend on the equipment fitted. Confirm which parts and tests apply on a 2012 Honda CR-V before pricing a repair.

Cause Estimated repair (USD)
Failed output shaft speed sensor element $150–$500
Damaged sensor connector or harness $80–$350
Metal debris on the sensor tip (from internal transmission wear) Cleaning the sensor face is a free first attempt. $100–$400
Damaged tone ring or reluctor wheel inside the transmission $1,500–$4,500
Transmission fluid contamination preventing the sensor from reading $200–$700
Wiring fault between the sensor and the TCM $100–$500
Failed TCM signal input (rare) $500–$1,500

These are editorial estimates in U.S. dollars. A shop can price a confirmed repair using the engine, parts and local labor rate.

How to diagnose this on a 2012 Honda CR-V

  1. Locate the output speed sensor on this transmission

    The output shaft speed sensor is typically a two-wire sensor threaded into the rear of the transmission case (RWD vehicles) or the side of the transaxle (FWD vehicles). Some vehicles have it on the transfer case for 4WD. Confirm location in the service manual.

    Tools: Vehicle-specific service information

  2. Check connector and visible wiring

    Sensor connectors near the transmission case are exposed to heat, road debris, and sometimes fluid leaks. Unplug and inspect for corrosion, transmission fluid migration up the harness, or visible damage. Clean and re-seat.

    Tools: Connector unlock tool, Electrical contact cleaner

  3. Measure sensor resistance

    Most output speed sensors are magnetic or Hall-effect with a typical resistance of 200–1500 Ω. Compare to the service manual. Infinite resistance means an open sensor; near zero means shorted. Either way, replace.

    Tools: Multimeter, Service spec sheet

  4. Verify signal output during rotation

    On a lift with the rear wheels free to rotate, spin a rear wheel slowly by hand while watching the output speed PID. The reading should change in proportion to wheel rotation. No response confirms a dead sensor or damaged tone ring.

    Tools: Vehicle lift, Scan tool with output speed PID

  5. Inspect sensor tip for debris

    Remove the sensor and look at the magnetic tip. Steel slivers stuck to the magnet are normal — large chunks or clutch material is a warning sign that the transmission is shedding material. Clean the tip and reinstall as a first attempt; consider transmission fluid analysis if heavy debris was present.

    Tools: Socket, Magnet pick or wire brush

NHTSA complaints & recalls for the 2012 Honda CR-V

Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Honda CR-V. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda CR-V diagnostics.

NHTSA snapshot taken October 21, 2026; refreshed quarterly. For live figures see NHTSA.gov .

403 owner complaints
27 involved a crash
4 involved a fire
24 reported injuries
  • ENGINE 89
  • POWER TRAIN 48
  • ELECTRICAL SYSTEM 68
  • UNKNOWN OR OTHER 52
  • STEERING 35

3 active recalls

  • POWER TRAIN:AUTOMATIC TRANSMISSION Apr 2013

    Honda is recalling certain model year 2012-2013 CR-V, Odyssey, and model year 2013 Acura RDX vehicles. During sub-freezing temperatures, the brake-shift interlock blocking mechanism may become slow and allow the gear selector to be moved from the Park position without pressing th…

    NHTSA campaign 13V143000
  • EQUIPMENT:OTHER:LABELS Oct 2012

    Honda is recalling certain model year 2012 CR-V, equipped with the LX trim level and manufactured from August 30, 2012, to August 31, 2012. These vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification." The incorrect values for Gross Vehicle Weight Ratin…

    NHTSA campaign 12V501000
  • LATCHES/LOCKS/LINKAGES:DOORS:LATCH Jul 2012

    Honda is recalling certain model year 2012 Honda CR-V and model year 2013 Acura ILX vehicles. If the manual or power door lock is activated while an interior front door handle is being operated by an occupant, the cable connecting the interior door handle to the door latch mechan…

    NHTSA campaign 12V338000

How do I fix P0720 on a 2012 Honda CR-V?

Engines in the 2012 Honda CR-V

The 2012 Honda CR-V was offered with the 2.4L 4-cylinder engine. Which one you have changes where P0720 is most likely to originate, so confirm your engine before ordering parts.

Engine data: EPA fueleconomy.gov.

Why P0720 puts the transmission into limp mode

The TCM continuously compares output shaft speed to engine RPM and selected gear to verify it is actually getting the gear ratio it commanded. Without a valid output speed signal:

A transmission may restrict shifting when the output-speed signal is lost. If acceleration or gear engagement is unpredictable, stop safely and arrange assistance. Follow the instructions for the warning displayed on your vehicle.

P0720 with metal on the sensor tip

A small amount of metallic dust on the magnetic sensor tip is normal — it’s the natural wear of bearings and gears over the life of the transmission. Large flakes or clutch material is not normal and indicates internal damage that will eventually cause shifting problems beyond the sensor. If you find heavy debris, do a fluid service and inspect the pan magnet too — together they tell the story of what’s happening inside.

P0720 vs P0500 (Vehicle Speed Sensor)

These can look similar but come from different sources:

On vehicles where the TCM derives “vehicle speed” from the output shaft sensor, both codes can set together from a single sensor failure.

P0720 on a 2012 Honda CR-V: frequently asked questions

What does diagnostic trouble code P0720 mean on a 2012 Honda CR-V?

P0720 is set when the transmission control module does not receive a valid signal from the output shaft speed sensor. The TCM uses this signal to compare actual transmission output to expected output for the selected gear and engine RPM — if the signal is missing or implausible, gear ratio calculations fail and the TCM cannot shift correctly. The vehicle typically drops into limp mode (stuck in a default gear, often 3rd or 4th) until the signal is restored.

What are the symptoms of P0720 on a 2012 Honda CR-V?

Check Engine Light is illuminated. Speedometer reads zero or fluctuates erratically. Transmission locked into a single gear (limp mode). Hard, harsh, or no shifts. Cruise control inoperative. Vehicle may shudder or hesitate at the moment of shift. Often paired with P0700 (transmission control malfunction)

What causes P0720 on a 2012 Honda CR-V?

Failed output shaft speed sensor element (estimated U.S. repair cost $150–$500). Damaged sensor connector or harness (estimated U.S. repair cost $80–$350). Metal debris on the sensor tip (from internal transmission wear) (estimated U.S. repair cost $100–$400). Damaged tone ring or reluctor wheel inside the transmission. Transmission fluid contamination preventing the sensor from reading. Wiring fault between the sensor and the TCM. Failed TCM signal input (rare)

Is it safe to drive a 2012 Honda CR-V with P0720?

P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.

Related diagnostic codes

P0720 on other Honda CR-V model years