P0720 on a 2012 Honda Accord

Transmission Output Speed Sensor Malfunction

P0720 on a 2012 Honda Accord means transmission output speed sensor malfunction. P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis. Use the symptoms and test results to narrow down the cause before replacing parts.

Severity: high Check warning lights Mid-size Sedan

Maintained by MECH AI Editorial · Technical content updated

What does P0720 mean on a 2012 Honda Accord?

P0720 is set when the transmission control module does not receive a valid signal from the output shaft speed sensor. The TCM uses this signal to compare actual transmission output to expected output for the selected gear and engine RPM — if the signal is missing or implausible, gear ratio calculations fail and the TCM cannot shift correctly. The vehicle typically drops into limp mode (stuck in a default gear, often 3rd or 4th) until the signal is restored.

The symptoms, causes, and diagnostic steps below describe P0720 itself, so they read the same on nearby Honda Accord model years. Powertrain and trim details vary year to year — confirm the specifics against your own vehicle before buying parts.

Is it safe to drive a 2012 Honda Accord with P0720?

P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.

What are the symptoms of P0720 on a 2012 Honda Accord?

What causes P0720 on a 2012 Honda Accord?

Possible causes of P0720 depend on the equipment fitted. Confirm which parts and tests apply on a 2012 Honda Accord before pricing a repair.

Cause Estimated repair (USD)
Failed output shaft speed sensor element $150–$500
Damaged sensor connector or harness $80–$350
Metal debris on the sensor tip (from internal transmission wear) Cleaning the sensor face is a free first attempt. $100–$400
Damaged tone ring or reluctor wheel inside the transmission $1,500–$4,500
Transmission fluid contamination preventing the sensor from reading $200–$700
Wiring fault between the sensor and the TCM $100–$500
Failed TCM signal input (rare) $500–$1,500

These are editorial estimates in U.S. dollars. A shop can price a confirmed repair using the engine, parts and local labor rate.

How to diagnose this on a 2012 Honda Accord

  1. Locate the output speed sensor on this transmission

    The output shaft speed sensor is typically a two-wire sensor threaded into the rear of the transmission case (RWD vehicles) or the side of the transaxle (FWD vehicles). Some vehicles have it on the transfer case for 4WD. Confirm location in the service manual.

    Tools: Vehicle-specific service information

  2. Check connector and visible wiring

    Sensor connectors near the transmission case are exposed to heat, road debris, and sometimes fluid leaks. Unplug and inspect for corrosion, transmission fluid migration up the harness, or visible damage. Clean and re-seat.

    Tools: Connector unlock tool, Electrical contact cleaner

  3. Measure sensor resistance

    Most output speed sensors are magnetic or Hall-effect with a typical resistance of 200–1500 Ω. Compare to the service manual. Infinite resistance means an open sensor; near zero means shorted. Either way, replace.

    Tools: Multimeter, Service spec sheet

  4. Verify signal output during rotation

    On a lift with the rear wheels free to rotate, spin a rear wheel slowly by hand while watching the output speed PID. The reading should change in proportion to wheel rotation. No response confirms a dead sensor or damaged tone ring.

    Tools: Vehicle lift, Scan tool with output speed PID

  5. Inspect sensor tip for debris

    Remove the sensor and look at the magnetic tip. Steel slivers stuck to the magnet are normal — large chunks or clutch material is a warning sign that the transmission is shedding material. Clean the tip and reinstall as a first attempt; consider transmission fluid analysis if heavy debris was present.

    Tools: Socket, Magnet pick or wire brush

NHTSA complaints & recalls for the 2012 Honda Accord

Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Honda Accord. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda Accord diagnostics.

NHTSA snapshot taken October 21, 2026; refreshed quarterly. For live figures see NHTSA.gov .

372 owner complaints
46 involved a crash
4 involved a fire
44 reported injuries
  • ENGINE 43
  • SEATS 64
  • AIR BAGS 56
  • STEERING 50
  • SERVICE BRAKES 35

8 active recalls

  • AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Jun 2019

    Honda (American Honda Motor Co.) is recalling certain 2009-2014 Acura TSX, 2011-2014 TSX Sport Wagon, 2010-2013 ZDX, 2008-2012 Honda Accord, 2010-2011 Accord Crosstour, 2006-2011 Civic and Civic Hybrid, 2008-2010 Civic GX NGV, 2012-2015 Crosstour, 2007-2011 CR-V, 2009-2013 Fit, 2…

    NHTSA campaign 19V502000
  • AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE May 2019

    Honda (American Honda Motor Co.) is recalling certain 2009-2014 Acura TSX, 2011-2013 TSX Sport Wagon, and 2010-2012 ZDX and 2008-2012 Honda Accord, 2010-2011 Accord Crosstour, 2006-2011 Civic, Civic Hybrid and Civic NGV, 2012-2014 Crosstour, 2007-2011 CR-V, 2009-2013 Fit, 2010-20…

    NHTSA campaign 19V378000
  • AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Sep 2018

    Honda (American Honda Motor Co.) is recalling certain 2014 Honda Insight and Acura TSX and TSX Wagon, 2014-2015 Honda Crosstour and Pilot vehicles nationwide, as well as certain 2014 Honda FCX Clarity and Fit EV vehicles in Florida, Hawaii, Puerto Rico, Texas, Alabama, Georgia, L…

    NHTSA campaign 18V661000
  • AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Apr 2018

    Honda (American Honda Motor Co.) is recalling certain 2003-2012 Honda Accord and Pilot, 2010 Accord Crosstour, 2001-2011 Civic, 2002-2011 CR-V, 2003-2004, 2006-2008 and 2011 Element, 2007 and 2009-2013 Fit, 2010-2012 Insight, 2002-2004 Odyssey, and 2012 Ridgeline vehicles. The fr…

    NHTSA campaign 18V268000

How do I fix P0720 on a 2012 Honda Accord?

Engines in the 2012 Honda Accord

The 2012 Honda Accord was offered with the 2.4L 4-cylinder and 3.5L 6-cylinder engines. Which one you have changes where P0720 is most likely to originate, so confirm your engine before ordering parts.

Engine data: EPA fueleconomy.gov.

Why P0720 puts the transmission into limp mode

The TCM continuously compares output shaft speed to engine RPM and selected gear to verify it is actually getting the gear ratio it commanded. Without a valid output speed signal:

A transmission may restrict shifting when the output-speed signal is lost. If acceleration or gear engagement is unpredictable, stop safely and arrange assistance. Follow the instructions for the warning displayed on your vehicle.

P0720 with metal on the sensor tip

A small amount of metallic dust on the magnetic sensor tip is normal — it’s the natural wear of bearings and gears over the life of the transmission. Large flakes or clutch material is not normal and indicates internal damage that will eventually cause shifting problems beyond the sensor. If you find heavy debris, do a fluid service and inspect the pan magnet too — together they tell the story of what’s happening inside.

P0720 vs P0500 (Vehicle Speed Sensor)

These can look similar but come from different sources:

On vehicles where the TCM derives “vehicle speed” from the output shaft sensor, both codes can set together from a single sensor failure.

P0720 on a 2012 Honda Accord: frequently asked questions

What does diagnostic trouble code P0720 mean on a 2012 Honda Accord?

P0720 is set when the transmission control module does not receive a valid signal from the output shaft speed sensor. The TCM uses this signal to compare actual transmission output to expected output for the selected gear and engine RPM — if the signal is missing or implausible, gear ratio calculations fail and the TCM cannot shift correctly. The vehicle typically drops into limp mode (stuck in a default gear, often 3rd or 4th) until the signal is restored.

What are the symptoms of P0720 on a 2012 Honda Accord?

Check Engine Light is illuminated. Speedometer reads zero or fluctuates erratically. Transmission locked into a single gear (limp mode). Hard, harsh, or no shifts. Cruise control inoperative. Vehicle may shudder or hesitate at the moment of shift. Often paired with P0700 (transmission control malfunction)

What causes P0720 on a 2012 Honda Accord?

Failed output shaft speed sensor element (estimated U.S. repair cost $150–$500). Damaged sensor connector or harness (estimated U.S. repair cost $80–$350). Metal debris on the sensor tip (from internal transmission wear) (estimated U.S. repair cost $100–$400). Damaged tone ring or reluctor wheel inside the transmission. Transmission fluid contamination preventing the sensor from reading. Wiring fault between the sensor and the TCM. Failed TCM signal input (rare)

Is it safe to drive a 2012 Honda Accord with P0720?

P0720 alone cannot tell you whether it is safe to drive. Follow your owner's manual for the warning lights and symptoms you see, and arrange diagnosis.

Related diagnostic codes

P0720 on other Honda Accord model years