P0497 on a 2012 Honda CR-V
EVAP Low Purge Flow
P0497 on a 2012 Honda CR-V indicates evap low purge flow. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failed purge valve stuck closed (mechanical or coil failure) (typically $80–$300). Confirm the root cause before replacing parts.
What does P0497 mean on a 2012 Honda CR-V?
P0497 is the inverse of P0496. The ECM commands the EVAP purge valve to flow vapor from the canister into the intake during a monitor test, and detects less flow than expected — or none at all. The cause is either the purge valve stuck closed, a restricted hose between the canister and the intake, a clogged charcoal canister, or the purge valve electrical circuit failing open.
This guide covers P0497 across the 2010-2014 Honda CR-V generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Honda CR-V with P0497?
In most cases a 2012 Honda CR-V stays drivable for short trips with P0497 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0497 on a 2012 Honda CR-V?
- Check Engine Light is illuminated
- Vehicle will fail emissions / smog testing
- Rarely any drivability symptom
- Possible faint fuel smell from a saturated canister
- Difficulty fueling at the pump (gas pump clicks off repeatedly)
What causes P0497 on a 2012 Honda CR-V?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failed purge valve stuck closed (mechanical or coil failure) | Most common | $80–$300 |
| Restricted or pinched hose between canister and purge valve | Common | $20–$150 |
| Wiring open on the purge valve circuit | Common | $80–$350 |
| Blocked or saturated EVAP charcoal canister | Occasional | $200–$600 |
| Failed PCM driver for the purge valve circuit | Rare | $400–$1,500 |
| Damaged or clogged EVAP service port creating a false low-flow reading | Rare | $30–$150 |
How to diagnose this on a 2012 Honda CR-V
-
Bench-test the purge valve
Remove the purge valve and apply 12 V. The valve should click audibly open. With voltage applied, blow air through the valve — air should pass freely. Without voltage, the valve should seal. A valve that does not open when commanded is the textbook P0497 cause.
Tools: 12 V test source, Hand vacuum / pressure pump
-
Verify the purge valve receives voltage during commanded operation
Use a bidirectional scan tool to command the purge valve open while back-probing the connector. Battery voltage should appear on the power wire when commanded. No voltage = open circuit, blown fuse, or PCM driver fault.
Tools: Bidirectional scan tool, Multimeter, Back-probe pins
-
Inspect the purge line for kinks or blockage
Trace the rubber line from the canister to the purge valve to the intake. Look for pinched sections (especially where the line passes under brackets), collapsed inner walls (common on aged rubber), or visible damage. A blocked line sets P0497 even with a perfect valve.
Tools: Flashlight, Inspection mirror
-
Test the charcoal canister
Disconnect the purge-side hose from the canister and try to pull vacuum on it with a hand pump. A healthy canister allows some airflow; a saturated canister blocks airflow entirely. If the canister won't pass air, replace it.
Tools: Hand vacuum pump
-
Read mode 6 EVAP test results
Mode 6 shows the measured purge flow during the most recent monitor run. Zero or very low flow confirms the diagnosis. A threshold-failure (just below acceptable) with a working valve points more at canister or hose restriction.
Tools: Scan tool with mode 6 support
NHTSA complaints & recalls for the 2012 Honda CR-V
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Honda CR-V. Use these to gauge how common a problem is on your specific vehicle before you start chasing Honda CR-V diagnostics.
- ENGINE 89
- POWER TRAIN 48
- ELECTRICAL SYSTEM 67
- UNKNOWN OR OTHER 51
- STEERING 35
3 active recalls
- EQUIPMENT:OTHER:LABELS Oct 2012
Honda is recalling certain model year 2012 CR-V, equipped with the LX trim level and manufactured from August 30, 2012, to August 31, 2012. These vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification." The incorrect values for Gross Vehicle Weight Rat…
NHTSA campaign 12V501000 - POWER TRAIN:AUTOMATIC TRANSMISSION Apr 2013
Honda is recalling certain model year 2012-2013 CR-V, Odyssey, and model year 2013 Acura RDX vehicles. During sub-freezing temperatures, the brake-shift interlock blocking mechanism may become slow and allow the gear selector to be moved from the Park position without pressing t…
NHTSA campaign 13V143000 - LATCHES/LOCKS/LINKAGES:DOORS:LATCH Jul 2012
Honda is recalling certain model year 2012 Honda CR-V and model year 2013 Acura ILX vehicles. If the manual or power door lock is activated while an interior front door handle is being operated by an occupant, the cable connecting the interior door handle to the door latch mecha…
NHTSA campaign 12V338000
How do I fix P0497 on a 2012 Honda CR-V?
- Replace the EVAP purge valve / purge solenoid
- Repair pinched or collapsed EVAP hose
- Replace the EVAP charcoal canister if saturated
- Repair open or broken purge valve wiring
About the 2010-2014 Honda CR-V
The 2010-2014 Honda CR-V was commonly sold with the following powertrains: 1.5L Turbo I4, 2.4L I4, 2.0L Hybrid I4. Common trims include LX, EX, EX-L, Touring.
P0497 vs P0496
These are the two opposite EVAP purge flow failures:
- P0496 — high purge flow / valve stuck open. Vapor flows into the intake when it shouldn’t. Often causes rough idle.
- P0497 — low purge flow / valve stuck closed. Vapor cannot reach the intake to be burned. The canister gradually saturates, fuel pump can have trouble refueling because the tank can’t vent through the purge path.
Both codes can come from the same physical part — purge valves fail open or closed about equally. Don’t assume the valve diagnoses to one direction over the other.
The “tank doesn’t vent on refuel” symptom
If P0497 sets and the gas pump keeps clicking off during refueling, the EVAP system can’t vent the displaced air from the tank through its normal path. This is mostly a refueling annoyance — it doesn’t affect drivability. But it’s a strong diagnostic clue when present.
Restricted hoses on aged rubber
EVAP hoses, especially the small-diameter rubber sections between the canister and the purge valve, harden and shrink over 10+ years. The inner wall can delaminate and partially block flow even when the outer hose looks fine. If P0497 returns after a valve replacement, swap the hose too — they aged at the same rate.
P0497 on a 2012 Honda CR-V: frequently asked questions
What does diagnostic trouble code P0497 mean on a 2012 Honda CR-V?
P0497 is the inverse of P0496. The ECM commands the EVAP purge valve to flow vapor from the canister into the intake during a monitor test, and detects less flow than expected — or none at all. The cause is either the purge valve stuck closed, a restricted hose between the canister and the intake, a clogged charcoal canister, or the purge valve electrical circuit failing open.
What are the symptoms of P0497 on a 2012 Honda CR-V?
Check Engine Light is illuminated. Vehicle will fail emissions / smog testing. Rarely any drivability symptom. Possible faint fuel smell from a saturated canister. Difficulty fueling at the pump (gas pump clicks off repeatedly)
What causes P0497 on a 2012 Honda CR-V?
Failed purge valve stuck closed (mechanical or coil failure) (most-common). Restricted or pinched hose between canister and purge valve (common). Wiring open on the purge valve circuit (common). Blocked or saturated EVAP charcoal canister (occasional). Failed PCM driver for the purge valve circuit (rare). Damaged or clogged EVAP service port creating a false low-flow reading (rare)
Is it safe to drive a 2012 Honda CR-V with P0497?
In most cases a 2012 Honda CR-V stays drivable for short trips with P0497 active, but it should be diagnosed and repaired promptly — this is a low-severity code. Ignoring it can lead to further damage or a failed emissions test.