P0442 on a 2012 Subaru Forester
EVAP Small Leak Detected
P0442 on a 2012 Subaru Forester indicates evap small leak detected. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is loose, worn, or cross-threaded fuel cap (typically $15–$60). Confirm the root cause before replacing parts.
What does P0442 mean on a 2012 Subaru Forester?
P0442 is set when the EVAP system's small-leak monitor detects an opening approximately 0.040 inches (1.0 mm) or larger. This is the equivalent of the gas cap being left slightly loose or a small crack in a vent hose. The vehicle remains fully drivable and consumes no extra fuel, but the EVAP system can no longer hold the sealed vacuum required for compliance.
This guide covers P0442 across the 2010-2014 Subaru Forester generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2010 through 2014.
Is it safe to drive a 2012 Subaru Forester with P0442?
In most cases a 2012 Subaru Forester stays drivable for short trips with P0442 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0442 on a 2012 Subaru Forester?
- Check Engine Light is illuminated
- Faint fuel smell, especially after refueling on a hot day
- No noticeable change in drivability or fuel economy
- Vehicle will fail emissions / smog testing
What causes P0442 on a 2012 Subaru Forester?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Loose, worn, or cross-threaded fuel cap | Most common | $15–$60 |
| Aged or split EVAP hose | Common | $30–$200 |
| Failing purge or vent valve seal | Common | $80–$350 |
| Cracked EVAP charcoal canister | Occasional | $200–$600 |
| Damaged O-rings at hose-to-canister or hose-to-solenoid connections | Occasional | $20–$120 |
| Pinhole or seam leak in the fuel filler neck | Occasional | $150–$600 |
| Failed fuel tank vent at the tank top (less accessible to inspect) | Rare | $300–$900 |
How to diagnose this on a 2012 Subaru Forester
-
Tighten or replace the fuel cap
Remove and reinstall the fuel cap to at least three clicks. Inspect the rubber gasket for cracks, debris, or compression set. Replace with an OEM-spec cap if the gasket is damaged or the cap is more than 8 years old.
Tools: None
-
Smoke-test the EVAP system
A 0.040-inch leak is too small to find by ear and almost always too small to see visually without smoke. Pressurize the EVAP system with smoke at the service port and trace the smoke trail to its source. Common leak points: behind the rear bumper near the canister, the hose between purge valve and intake, and the top of the fuel tank.
Tools: EVAP smoke machine, UV dye (optional), Inspection mirror and flashlight
-
Inspect the EVAP service port itself
The green EVAP service port cap is a frequent leak point because its O-ring hardens and fails after years of heat cycles. With smoke already in the system, watch the service port specifically.
Tools: Inspection mirror
-
Visually inspect the charcoal canister
Many trucks and SUVs mount the canister behind the rear axle where it is exposed to road debris and salt spray. Cracks in the plastic housing are common on aging vehicles. Replace the canister if cracked or saturated.
Tools: Floor jack and stands, Trim panel tools
-
Verify monitor completion before re-testing
After repair, drive 2–4 cold-start drive cycles with the tank between 25 % and 75 % full. Use a scan tool to confirm the EVAP readiness flag turns "ready." Clearing the code prematurely will set the light again as soon as the monitor runs.
Tools: Scan tool with readiness monitor display
NHTSA complaints & recalls for the 2012 Subaru Forester
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2012 Subaru Forester. Use these to gauge how common a problem is on your specific vehicle before you start chasing Subaru Forester diagnostics.
- ENGINE 27
- VEHICLE SPEED CONTROL 18
- AIR BAGS 20
- SERVICE BRAKES 15
- ELECTRICAL SYSTEM 10
15 active recalls
- AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Jan 2019
Subaru of America, Inc. (Subaru) is recalling certain 2010-2014 Tribeca, WRX, Outback, and Legacy vehicles, 2010-2011 Impreza vehicles and 2010-2013 Forester vehicles sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana,…
NHTSA campaign 19V008000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Jan 2019
Subaru of America, Inc. (Subaru) is recalling certain 2010-2013 Forester, 2010-2014 Tribeca, WRX, Outback, Legacy, and 2010-2011 Impreza vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texa…
NHTSA campaign 19V007000 - AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE Jan 2019
Subaru of America, Inc. (Subaru) is recalling certain 2010-2014 Tribeca, WRX, Legacy and Outback vehicles, 2010-2011 Impreza vehicles and 2010-2013 Forester vehicles sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michi…
NHTSA campaign 19V009000 - ELECTRICAL SYSTEM:IGNITION:SWITCH Apr 2019
Subaru of America, Inc. (Subaru) is recalling certain 2009-2013 Forester vehicles, 2008-2011 Impreza vehicles, 2008-2014 WRX vehicles, 2005-2014 Legacy vehicles, 2005-2014 Outback vehicles and 2006-2008 Tribeca vehicles equipped with a mechanical key ignition switch installed as…
NHTSA campaign 19V297000
How do I fix P0442 on a 2012 Subaru Forester?
- Replace the fuel cap
- Replace cracked EVAP hoses and aged O-rings
- Replace the EVAP purge valve or vent valve
- Replace the charcoal canister assembly
- Replace the fuel filler neck (rust or pinhole)
About the 2010-2014 Subaru Forester
The 2010-2014 Subaru Forester was commonly sold with the following powertrains: 2.5L H4, 2.0L Turbo H4. Common trims include Base, Premium, Sport, Limited, Touring, Wilderness.
P0442 vs P0455 vs P0456
The three EVAP leak codes describe the same kind of fault at different leak sizes:
| Code | Leak size threshold | Typical real-world cause |
|---|---|---|
| P0456 | ~0.020” (very small) | Cap O-ring, fresh hose pinhole |
| P0442 | ~0.040” (small) | Loose cap, aging hose, cracked vent valve seal |
| P0455 | ~0.090”+ (large or no seal) | Missing cap, disconnected hose, large canister crack |
A vehicle that sets P0456 today often sets P0442 in a few months as the same crack grows.
Why smoke testing is non-negotiable
EVAP leaks are usually too small to find any other way. A bare-eye inspection of every hose and joint will miss most P0442 causes. The smoke machine is a one-time tool purchase (or one-time shop diagnostic fee) that pays for itself on the first EVAP repair.
What “0.040 inch leak” actually means
OBD-II EVAP monitors do not measure the leak directly. They apply a calibrated vacuum or pressure to the sealed system and time how quickly it bleeds off. The leak-equivalent diameter is calculated from that decay rate. A real-world 0.040” hole and a 0.030” hole with a smaller restriction upstream can produce the same monitor result.