P0440 on a 2022 Toyota Highlander
EVAP System Malfunction (Generic)
P0440 on a 2022 Toyota Highlander indicates evap system malfunction (generic). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is loose, worn, or wrong-spec fuel cap (typically $15–$60). Confirm the root cause before replacing parts.
What does P0440 mean on a 2022 Toyota Highlander?
P0440 is a generic evaporative emission (EVAP) system fault. The EVAP system captures fuel vapors from the tank and routes them through the charcoal canister to be burned by the engine instead of vented into the atmosphere. P0440 is set when the ECM detects that this sealed system has lost its ability to hold pressure or vacuum during a leak test. It is almost always the first sign of a small leak somewhere between the fuel tank and the engine intake.
This guide covers P0440 across the 2020-2024 Toyota Highlander generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Toyota Highlander with P0440?
In most cases a 2022 Toyota Highlander stays drivable for short trips with P0440 active, but diagnose and repair it promptly. This is a low-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0440 on a 2022 Toyota Highlander?
- Check Engine Light is illuminated
- Faint fuel smell when filling the tank or shortly after
- No drivability problem in most cases
- Fuel-cap warning light on some vehicles
- Vehicle will fail emissions / smog testing
What causes P0440 on a 2022 Toyota Highlander?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Loose, worn, or wrong-spec fuel cap Always the first thing to check — costs nothing to tighten or replace. | Most common | $15–$60 |
| Cracked, kinked, or disconnected EVAP hose | Common | $30–$200 |
| Failed EVAP purge valve (purge solenoid) stuck open or closed | Common | $80–$300 |
| Failed EVAP canister vent valve / vent solenoid | Common | $80–$350 |
| Cracked or damaged EVAP charcoal canister | Occasional | $200–$600 |
| Pinhole leak in fuel filler neck or tank seam | Occasional | $150–$800 |
| Failed fuel tank pressure sensor | Occasional | $100–$350 |
How to diagnose this on a 2022 Toyota Highlander
-
Inspect and re-seat the fuel cap
Remove the fuel cap and check the rubber gasket for damage, debris, or twisting. Reinstall hand-tight until the cap clicks. Many vehicles require 3+ click stops. Clear the code and drive several drive cycles to allow the EVAP monitor to retest.
Tools: None
-
Read mode 6 / EVAP monitor data
Pull mode 6 test results for the EVAP system. Look at the small-leak, large-leak, and purge flow test IDs. The specific test that failed narrows the diagnosis from "EVAP system" to which subsystem within it.
Tools: Scan tool with mode 6 support
-
Smoke-test the EVAP system
Introduce low-pressure smoke (typically 0.5 psi) into the EVAP service port. Inspect every hose joint, the charcoal canister, the purge and vent solenoids, the filler neck, and the tank top. Smoke escaping anywhere is the leak — repair it and retest.
Tools: EVAP smoke machine, UV dye and light (optional), Inspection mirror
-
Bench-test the purge valve and vent valve
Remove the purge valve and apply 12 V across its terminals. It should click and open. With no voltage, it should hold vacuum. The vent valve operates in reverse — normally open, closes when energized. Either valve stuck the wrong way will set P0440.
Tools: 12 V test source, Hand vacuum pump
-
Check the fuel tank pressure sensor reading
Compare the live tank pressure PID to a known-good vehicle. A reading that does not change when the cap is removed or when the purge valve is commanded indicates either a failed sensor or a blocked hose to it.
Tools: Scan tool
NHTSA complaints & recalls for the 2022 Toyota Highlander
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Toyota Highlander. Use these to gauge how common a problem is on your specific vehicle before you start chasing Toyota Highlander diagnostics.
- POWER TRAIN 36
- STRUCTURE 39
- SERVICE BRAKES 35
- UNKNOWN OR OTHER 30
- AIR BAGS 21
5 active recalls
- EQUIPMENT:OTHER:LABELS May 2022
Gulf States Toyota, Inc. (GST) is recalling certain 2022 4Runner, Tacoma, Highlander, and Highlander Hybrid vehicles. The load carrying capacity modification labels may not be permanent and can fade, becoming illegible. As such, these vehicles fail to comply with the requiremen…
NHTSA campaign 22V310000 - STRUCTURE:BODY:BUMPERS Oct 2023
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2020-2023 Highlander & Highlander Hybrid vehicles. During normal vehicle operation, minor impact to the front lower bumper cover may result in the cover coming loose or detaching.…
NHTSA campaign 23V720000 - TIRES Jun 2024
Gulf States Toyota, Inc. (GST) is recalling certain 2022-2024 model year Highlander L and Highlander LE vehicles equipped with the Blackout Package that includes 20" black alloy wheels and tires. The installed tires have an insufficient load rating. As such, these vehicles fail…
NHTSA campaign 24V419000 - TIRES Jun 2024
Southeast Toyota Distributors, LLC (SET) is recalling certain 2021-2024 Highlander vehicles. The 20-inch accessory tires with an insufficient load rating for the vehicle's Gross Axle Weight Rating (GAWR) were installed. As such, these vehicles fail to comply with the requiremen…
NHTSA campaign 24V452000
How do I fix P0440 on a 2022 Toyota Highlander?
- Replace the fuel cap with an OEM spec part
- Replace cracked or aged EVAP hoses
- Replace the EVAP purge valve
- Replace the EVAP vent valve / vent solenoid
- Replace the EVAP charcoal canister
About the 2020-2024 Toyota Highlander
The 2020-2024 Toyota Highlander was commonly sold with the following powertrains: 3.5L V6, 2.4L Turbo I4, 2.5L Hybrid I4. Common trims include L, LE, XLE, XSE, Limited, Platinum.
P0440 vs the more specific EVAP codes
P0440 is the catch-all. If the ECM can identify the type of failure more specifically, it will set a narrower code: P0442 (small leak), P0455 (large leak), P0446 (vent control), and so on. Older vehicles often set P0440 when newer vehicles would set one of the more specific codes for the same underlying condition.
Why the gas cap is always step one
A loose or damaged gas cap accounts for roughly one-third of all P0440 set events. The cap is the cheapest part to replace and the most common point of failure. Always tighten until you hear 3+ clicks, and replace any cap whose gasket shows cracks or hardening.
How long after a repair until the code clears
The EVAP leak test only runs under specific conditions: cold soak (engine off for several hours), partial fuel tank (typically 25–75 % full), and a specific outside temperature range. After a repair, expect 2–4 drive cycles before the monitor completes and the readiness flag turns “ready.” Clearing the code with a scan tool removes the light immediately, but the monitor must complete naturally before emissions testing will pass.