P0343 on a 2022 Toyota Camry
Cam Position Sensor High Input (Bank 1)
P0343 on a 2022 Toyota Camry indicates cam position sensor high input (bank 1). It usually stays drivable short-term but should be diagnosed promptly. The most common cause is open circuit in the cam sensor signal wire or its ground (typically $80–$350). Confirm the root cause before replacing parts.
What does P0343 mean on a 2022 Toyota Camry?
P0343 is set when the ECM sees the Bank 1 "A" camshaft position sensor circuit sitting above its calibrated maximum voltage. On most engines "A" is the intake camshaft, or the single cam sensor on engines with only one. Because a Hall-effect cam sensor normally idles near reference voltage and pulls the line low as each reluctor tooth passes, a circuit stuck high usually means the sensor is not pulling at all: an open signal or ground circuit, a short to a power source, or a dead sensor. P0343 is the mirror image of P0342.
The symptoms, causes, and diagnostic steps below describe P0343 itself, so they read the same on nearby Toyota Camry model years. Powertrain and trim details vary year to year — confirm the specifics against your own vehicle before buying parts.
Is it safe to drive a 2022 Toyota Camry with P0343?
In most cases a 2022 Toyota Camry stays drivable for short trips with P0343 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0343 on a 2022 Toyota Camry?
- Check Engine Light is illuminated
- Hard start with extended cranking
- Possible complete no-start condition
- Stalling, sometimes intermittent
- Rough running and reduced power
- Hesitation under acceleration
- Reduced fuel economy
What causes P0343 on a 2022 Toyota Camry?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Open circuit in the cam sensor signal wire or its ground | Most common | $80–$350 |
| Failed camshaft position sensor (output stuck high) | Most common | $100–$400 |
| Cam sensor signal wire shorted to a power source | Common | $80–$350 |
| Corroded connector adding resistance to the signal or ground path | Common | $50–$250 |
| Loose or incorrectly torqued sensor leaving the air gap too large Costs nothing to check — a sensor backed out of its bore reads high because it never sees the reluctor. | Occasional | $20–$100 |
| Damaged or missing teeth on the camshaft reluctor / tone wheel | Occasional | $300–$1,200 |
| Failed PCM input for the cam sensor circuit | Rare | $400–$1,500 |
Cost ranges are editorial estimates for parts and labor at an independent U.S. shop — not quotes. What you actually pay moves with your region, the shop's hourly rate, which engine you have, and how much diagnostic time the job takes. Dealer service departments typically sit above these ranges.
How to diagnose this on a 2022 Toyota Camry
-
Confirm the sensor is seated and torqued
Before any electrical testing, check that the sensor is fully seated in its bore and its bolt is tight. A sensor backed out even a few millimetres — by a loose bolt, a missing spacer, or a previous repair — sits too far from the reluctor to trigger and reports a permanently high circuit. This is a five-minute check that occasionally ends the whole diagnosis.
Tools: Socket set, Torque wrench
-
Inspect the connector and harness
Unplug the sensor and look for pushed-back or corroded pins, oil intrusion, and chafing where the harness crosses brackets or the valve cover. High-input codes are frequently a poor ground connection, and a green crusty ground pin is the visual signature of one.
Tools: Connector unlock tool, Flashlight, Electrical contact cleaner
-
Check the ground circuit resistance
With the connector unplugged, measure resistance from the sensor's ground pin to a known-good chassis ground. It should be very close to zero. Anything more than a couple of ohms is a bad ground, and a bad ground is one of the most common reasons a perfectly good sensor reports high.
Tools: Multimeter, Wiring diagram
-
Test the signal circuit for a short to power
Unplug both the sensor and, if you can access it safely, the ECM connector. Measure the signal wire against ground with the key on. Voltage present on a wire that is disconnected at both ends means it is touching a power source somewhere along its run — find and repair the chafe point.
Tools: Multimeter, Wiring diagram
-
Scope the signal during cranking
Capture the waveform while cranking. A working sensor produces clean square pulses that swing from reference voltage down toward ground. A flat trace sitting at the top rail confirms the sensor is never switching — either it is dead, or the reluctor is not passing close enough to trigger it.
Tools: Oscilloscope, Back-probe pins
Known Technical Service Bulletins for the 2020-2024 Toyota Camry
Manufacturers publish Technical Service Bulletins (TSBs) when a known issue affects a specific vehicle. These bulletins come from the NHTSA database for your Toyota Camry.
- ENGINE Feb 27, 2026
OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.
NHTSA #11029896 - ELECTRICAL SYSTEM Jan 30, 2026
OBSOLETE NOTICE January 30, 2026: This bulletin is now obsolete. Please see T-SB-0001-26.
NHTSA #11028726 - ELECTRICAL SYSTEM Jan 28, 2026
Some 2018 – 2024 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.
NHTSA #11028722 - UNKNOWN OR OTHER Jan 7, 2026
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA #11028712 - ENGINE Aug 7, 2025
The specific condition covered by this program is for a small engine coolant leak that can occur from the flow shut-off valve that can allow coolant to drip on other parts of the vehicle. This can cause "Engine Maintenance Required" to be displayed on the instrument cluster or cause the A/C not to function normally. Although the flow shut-off valve is covered by Toyota’s New Vehicle Limited Warranty for 36 months or 36,000 miles (whichever comes first), we at Toyota care about the customers’ ownership experience. Toyota is providing coverage for repairs related to Flow Shut-off Valve Coolant Leak.
NHTSA #11022949 - ELECTRICAL SYSTEM Jun 25, 2025
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
NHTSA #11020670
+14 more TSBs available in MECH AI's TSB explorer for this vehicle.
NHTSA complaints & recalls for the 2022 Toyota Camry
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Toyota Camry. Use these to gauge how common a problem is on your specific vehicle before you start chasing Toyota Camry diagnostics.
- VEHICLE SPEED CONTROL 6
- AIR BAGS 10
- UNKNOWN OR OTHER 7
- SERVICE BRAKES 7
- ELECTRICAL SYSTEM 7
1 active recall
- AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION Dec 2023
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2020-2021 Avalon, Avalon Hybrid, Corolla, Highlander, Highlander Hybrid, RAV4, RAV4 Hybrid, Lexus ES350, Lexus RX350, Lexus RX450H, 2021 Sienna Hybrid, Lexus ES250, 2020-2022 Camry, Camry Hybrid, and ES300H ve…
NHTSA campaign 23V865000
How do I fix P0343 on a 2022 Toyota Camry?
- Replace the camshaft position sensor with an OEM part
- Repair the open signal or ground circuit
- Repair a signal wire shorted to power
- Clean or repair the sensor connector and its ground
- Re-seat and correctly torque the cam sensor
Engines in the 2022 Toyota Camry
The 2022 Toyota Camry was offered with the 2.5L 4-cylinder and 3.5L 6-cylinder engines, including a hybrid version. Which one you have changes where P0343 is most likely to originate, so confirm your engine before ordering parts.
Engine data: EPA fueleconomy.gov.
P0343 vs P0342
Same sensor, opposite electrical failures:
- P0342 (low input) — the circuit is being pulled toward ground when it shouldn’t be. Look for a short to ground or a sensor that has failed low.
- P0343 (high input) — the circuit is stuck near reference voltage and never pulls down. Look for an open circuit, a bad ground, or a sensor that is not switching.
Both are voltage-rail faults, which is why both tend to be wiring problems more often than the sensor. The exception is a sensor that has failed internally in a way that leaves the output line unloaded, which looks identical to an open circuit from the ECM’s side.
Check the air gap before you check anything electrical
A cam sensor reads the passing teeth of a reluctor wheel across a small air gap. If that gap is too big, the sensor never triggers, and the ECM sees a circuit that is permanently high — exactly P0343. Causes of a too-large gap are mundane: a loose mounting bolt, a sensor not pushed fully home during a previous job, a missing shim, or debris packed into the bore. Take thirty seconds to confirm the sensor is seated and tight before you start chasing wires.
Why the ground circuit deserves suspicion
Cam sensor grounds often share a splice with several other engine sensors. When that splice corrodes, the sensor cannot pull its signal line down properly, and the circuit reads high. The tell is other seemingly unrelated sensor codes setting alongside P0343 — if you have a scattering of codes that don’t share a system, stop testing sensors and go find the shared ground.
When this becomes a shop job
If the wiring tests clean, the ground is solid, a new OEM sensor is installed, and P0343 still returns, the remaining suspect is the reluctor wheel itself — chipped teeth, a slipped press-fit ring, or debris on the target. Seeing it usually means removing the timing cover, which is where the job stops being a driveway repair on most modern engines.
P0343 on a 2022 Toyota Camry: frequently asked questions
What does diagnostic trouble code P0343 mean on a 2022 Toyota Camry?
P0343 is set when the ECM sees the Bank 1 "A" camshaft position sensor circuit sitting above its calibrated maximum voltage. On most engines "A" is the intake camshaft, or the single cam sensor on engines with only one. Because a Hall-effect cam sensor normally idles near reference voltage and pulls the line low as each reluctor tooth passes, a circuit stuck high usually means the sensor is not pulling at all: an open signal or ground circuit, a short to a power source, or a dead sensor. P0343 is the mirror image of P0342.
What are the symptoms of P0343 on a 2022 Toyota Camry?
Check Engine Light is illuminated. Hard start with extended cranking. Possible complete no-start condition. Stalling, sometimes intermittent. Rough running and reduced power. Hesitation under acceleration. Reduced fuel economy
What causes P0343 on a 2022 Toyota Camry?
Open circuit in the cam sensor signal wire or its ground (most-common). Failed camshaft position sensor (output stuck high) (most-common). Cam sensor signal wire shorted to a power source (common). Corroded connector adding resistance to the signal or ground path (common). Loose or incorrectly torqued sensor leaving the air gap too large (occasional). Damaged or missing teeth on the camshaft reluctor / tone wheel (occasional). Failed PCM input for the cam sensor circuit (rare)
Is it safe to drive a 2022 Toyota Camry with P0343?
In most cases a 2022 Toyota Camry stays drivable for short trips with P0343 active, but it should be diagnosed and repaired promptly — this is a high-severity code. Ignoring it can lead to further damage or a failed emissions test.