P0341 on a 2022 Ford Mustang
Camshaft Position Sensor Range / Performance
P0341 on a 2022 Ford Mustang indicates camshaft position sensor range / performance. It usually stays drivable short-term but should be diagnosed promptly. The most common cause is failing camshaft position sensor (degraded signal) (typically $100–$400). Confirm the root cause before replacing parts.
What does P0341 mean on a 2022 Ford Mustang?
P0341 is set when the ECM does receive a camshaft position signal, but the signal does not behave the way it should — pulses are arriving at unexpected intervals, the cam-crank correlation is drifting, or the signal pattern is irregular. Unlike P0340 (no signal at all), P0341 means the sensor is communicating, but its output is unreliable. The result is rough running, hard starts, and sometimes stalling.
This guide covers P0341 across the 2020-2024 Ford Mustang generation — the symptoms, causes, and diagnostic steps below apply to every model year from 2020 through 2024.
Is it safe to drive a 2022 Ford Mustang with P0341?
In most cases a 2022 Ford Mustang stays drivable for short trips with P0341 active, but diagnose and repair it promptly. This is a high-severity code — ignoring it can lead to further damage or a failed emissions test.
What are the symptoms of P0341 on a 2022 Ford Mustang?
- Check Engine Light is illuminated
- Hard cold start with extended crank time
- Intermittent rough running or misfires
- Stalling at idle or coming to a stop
- Reduced power, especially at higher RPM
- Hesitation under acceleration
- Possible heat-soak failure pattern
What causes P0341 on a 2022 Ford Mustang?
| Cause | Likelihood | Estimated repair (USD) |
|---|---|---|
| Failing camshaft position sensor (degraded signal) | Most common | $100–$400 |
| Damaged or chafed cam sensor wiring | Common | $80–$350 |
| Cam tone ring / reluctor damaged or contaminated with debris | Common | $300–$1,500 |
| Stretched timing chain causing cam-crank correlation drift | Occasional | $800–$3,000 |
| Loose or improperly torqued cam sensor mounting | Occasional | $20–$100 |
| Oil leak at the cam sensor port causing intermittent shorts | Occasional | $80–$350 |
How to diagnose this on a 2022 Ford Mustang
-
Compare cam and crank position signals in live data
Watch cam and crank position PIDs simultaneously while cranking and at idle. Healthy cam-crank correlation maintains a fixed offset. Drift in the offset under load suggests chain stretch; missing or noisy cam pulses point at the sensor or wiring.
Tools: Scan tool with dual-PID graphing
-
Scope the cam sensor signal directly
With an oscilloscope on the cam signal wire, capture the waveform during cranking and at idle. A healthy Hall-effect sensor produces clean square pulses. A variable-reluctance sensor produces clean sine pulses. Noisy, missing, or irregular pulses confirm a sensor or wiring problem.
Tools: Oscilloscope, Back-probe pins
-
Inspect the cam reluctor for damage
Remove the cam sensor and shine a light through the port to see the cam reluctor teeth. Damaged teeth, oil/sludge buildup, or a slipped reluctor wheel will produce P0341. Some engines have hand-pressed reluctors that have been known to slip on the camshaft.
Tools: Inspection mirror, Bright flashlight
-
Check for oil leaking into the cam sensor port
The cam sensor o-ring or gasket can fail and let oil into the sensor body. Oil intrusion shorts the internal electronics intermittently — the sensor reads correctly cold, fails when warm. Replace the sensor with a new o-ring.
Tools: O-ring kit, Clean rags
-
Inspect wiring for chafing
Cam sensor harnesses route near the engine top, exposed to heat and vibration. A chafe point against a metal bracket can create an intermittent short. Visually inspect every inch of the harness, especially where it bends around brackets or near the valve cover.
Tools: Flashlight, Inspection mirror
NHTSA complaints & recalls for the 2022 Ford Mustang
Owner-reported safety complaints and official recalls filed with the U.S. National Highway Traffic Safety Administration for the 2022 Ford Mustang. Use these to gauge how common a problem is on your specific vehicle before you start chasing Ford Mustang diagnostics.
- FUEL SYSTEM 8
- GASOLINE 8
- UNKNOWN OR OTHER 7
- ELECTRICAL SYSTEM 7
- STEERING 6
9 active recalls
- AIR BAGS:KNEE BOLSTER Feb 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang vehicles. An insufficient weld on the front passenger knee air bag may result in an improper air bag deployment.…
NHTSA campaign 22V083000 - FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA May 2022
Ford Motor Company (Ford) is recalling certain 2022 Mustang vehicles equipped with an Image Processing Module A (IPMA) or forward-facing camera. The camera is misaligned to the vehicle, resulting in the camera not functioning as intended.…
NHTSA campaign 22V334000 - POWER TRAIN:AUTOMATIC TRANSMISSION Feb 2023
Ford Motor Company (Ford) is recalling certain 2022-2023 F-150, Mustang, Explorer, Bronco, and 2023 Lincoln Aviator vehicles equipped with automatic transmissions. The transmission may contain a loose bolt which could prevent the transmission from engaging the park gear, althoug…
NHTSA campaign 23V070000 - ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM Oct 2023
Ford Motor Company (Ford) is recalling certain 2020-2023 Mustang vehicles. The brake fluid level sensor may not activate the visual warning indicator when the brake fluid is low. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standa…
NHTSA campaign 23V727000
How do I fix P0341 on a 2022 Ford Mustang?
- Replace the camshaft position sensor with an OEM part
- Replace the cam sensor o-ring / gasket and the sensor together
- Repair damaged sensor wiring
- Replace stretched timing chain (if correlation drift confirmed)
- Replace slipped cam reluctor wheel
About the 2020-2024 Ford Mustang
The 2020-2024 Ford Mustang was commonly sold with the following powertrains: 2.3L EcoBoost I4, 5.0L V8, 5.2L V8. Common trims include EcoBoost, GT, Mach 1, Shelby GT500, Dark Horse.
P0340 vs P0341
The two cam sensor codes describe different failure modes of the same sensor:
- P0340 — no signal at all. Open circuit, dead sensor, missing power or ground.
- P0341 — signal present but degraded. The sensor is working but its output is unreliable. The diagnostic targets signal quality rather than presence.
P0341 is harder to diagnose because the sensor often passes basic resistance tests. A scope is the right tool — multimeter tests don’t reveal pulse-pattern problems.
When P0341 is actually a timing chain problem
On engines with documented chain wear (BMW N20/N26, Ford 5.4 3V, GM 3.6 LFX/LLT, VW EA888), P0341 can be the first symptom of chain stretch. The cam moves slightly out of phase with the crank as the chain wears — the cam sensor reports its position correctly but it doesn’t agree with where the ECM thinks it should be. Replace the sensor first as the cheap test; if P0341 returns and chain rattle is audible, the chain is the cause.
Oil-soaked cam sensors
If you remove a cam sensor and oil pours out of the port, the sensor body is oil-saturated and the internal electronics are compromised. Replace both the sensor and the o-ring / seal that let oil in. Just cleaning and reinstalling sets P0341 again within weeks.